Page 2 - Installation Instructions; DISCLAIMER
LPK1 Installation Instructions 2 DISCLAIMER Milestone AV Technologies and its affiliated corporations andsubsidiaries (collectively "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all details,conditi...
Page 3 - LEGEND
Installation Instructions LPK1 3 LEGEND DIMENSIONS Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijación Befestigungsteil lösen Desapertar fixador Allent...
Page 4 - TOOLS REQUIRED FOR INSTALLATION
LPK1 Installation Instructions 4 TOOLS REQUIRED FOR INSTALLATION PARTS 1/2" 7/32" (wood stud)5/16" (concrete) A (1)[LPK1 bracket]
Page 5 - PREPARATION; Figure 1; INSTALLATION; Wood Installation; This will require knowing the lens to; Figure 3
Installation Instructions LPK1 5 PREPARATION 1. Remove and SAVE four nuts from top of VCM mount (not included). (See Figure 1) 2. Remove and discard top slide plate. (See Figure 1) Figure 1 3. Place LPK1 mount (A) open side up on top of VCM, withVCM studs fitting through LPK1 slots. (See Figure 2) 4...
Page 6 - Figure 4; Solid Concrete Installation; MUST; Figure 5; Make sure mount is properly oriented; Figure 6
LPK1 Installation Instructions 6 4. Align four mounting holes in LPK1 with four pilot holes. (SeeFigure 4) IMPORTANT ! : Make sure mount is properly oriented towards target before securing to structure. 5. Secure LPK1 to structure using four 5/16" flat washers andfour 5/16" x 2-1/2" hex ...
Page 7 - Threaded Rod Installation; Figure 7; INSTALLING PROJECTOR
Installation Instructions LPK1 7 Threaded Rod Installation The LPK1 may be suspended from four 3/8" diameter ASTMA307 or stronger threaded rods (not included) which aresecured to a 1-5/8" x 1-5/8" 12ga metal framing strut channel(spanning a maximum of 4 feet--not included) by ASTM A307 o...
Page 8 - CLAUSES DE NON-RESPONSABILITÉ
LPK1 Installation Instructions 8 CLAUSES DE NON-RESPONSABILITÉ Milestone AV Technologies, ainsi que ses filiales et entreprisesaffiliées (collectivement « Milestone »), ont fait en sorte que cemanuel soit exact et exhaustif. Cependant, Milestone negarantit pas que les informations contenues dans le ...
Page 9 - DIMENSIONS
Installation Instructions LPK1 9 DIMENSIONS OUTILS NÉCESSAIRES À L'INSTALLATION PIÈCES 15.50393.7 0.34 8.7 0.56 14.2 2X DIMENSIONS : POUCES [MILLIMÈTRES] 12,7 mm (1/2") 5,5 mm (7/32") (montant en bois)8 mm (5/16") (béton) A (1) [patte de fixation LPK1]
Page 10 - PRÉPARATION; Installation sur des montants en bois
LPK1 Installation Instructions 10 PRÉPARATION 1. Retirez et CONSERVEZ les quatre écrous sur la partie supérieure du système de montage VCM (non fourni).(voir la Figure 1) 2. Retirez et mettez de côté la plaque coulissante supérieure.(voir la Figure 1) Figure 1 3. Placez le système de montage LPK1 (A...
Page 11 - Installation sur du béton solide; DOIVENT
Installation Instructions LPK1 11 4. Alignez les quatre trous de montage dans le LPK1 sur lesquatre avant-trous. (voir la Figure 4) IMPORTANT ! Assurez-vous que le système de montage est correctement orienté vers la cible avant de le fixer sur lastructure. 5. Fixez le LPK1 sur la structure à l'aide ...
Page 12 - Installation à l'aide de tiges filetées; INSTALLATION DU PROJECTEUR
LPK1 Installation Instructions 12 Installation à l'aide de tiges filetées Le LPK1 peut être suspendu à l'aide de quatre tiges filetées(non fournies) de 9,5 mm (3/8") de diamètre de calibre ASTMA307 ou supérieur, arrimées à un profilé métallique de calibre12 de 1-5/8" x 1-5/8" (d'une long...
Page 13 - HAFTUNGSAUSSCHLUSS
Installation Instructions LPK1 13 HAFTUNGSAUSSCHLUSS Milestone AV Technologies sowie seine konzerneigenenUnternehmen und Tochtergesellschaften (zusammen"Milestone") haben versucht, dieses Handbuch so genau undvollständig als möglich zu gestalten. Milestone erhebt jedochweder Anspruch auf Vol...
Page 14 - ABMESSUNGEN
LPK1 Installation Instructions 14 ABMESSUNGEN FÜR DIE MONTAGE ERFORDERLICHES WERKZEUG TEILE 15.50393.7 0.34 8.7 0.56 14.2 2X ABMESSUNGEN: ZOLL [MILLIMETER] 12,7 mm (1/2") 5,5 mm (7/32") (Holzbalken) 8 mm (5/16") (Beton) A (1) [LPK1-Anschlussplatte]
Page 15 - VORBEREITUNG; Montage an Holzbalken; Hierzu müssen Sie den Abstand zwischen
Installation Instructions LPK1 15 VORBEREITUNG 1. Entfernen Sie die vier Muttern von der Oberseite der(nicht mitgelieferten) VCM-Halterung und BEWAHREN Sie sie AUF . (Siehe Abb. 1) 2. Entfernen Sie die obere, verschiebbare Platte, sie ist nunüberflüssig. (Siehe Abb. 1) Abb. 1 3. Platzieren Sie die L...
Page 16 - Montage an Massivbeton; MÜSSEN; Stellen Sie sicher, dass die Halterung genau
LPK1 Installation Instructions 16 4. Richten Sie die vier Montagebohrungen im LPK1 nach denvier Vorbohrungen aus. (Siehe Abb. 4) WICHTIG! Stellen Sie sicher, dass die Halterung genau auf das Ziel gerichtet ist, bevor Sie sie an derKonstruktion befestigen. 5. Befestigen Sie das LPK1 mit vier 5/16"...
Page 17 - Montage an Gewindestangen; MONTAGE DES PROJEKTORS
Installation Instructions LPK1 17 Montage an Gewindestangen Das LPK1 kann an vier ASTM A307-Gewindestangen mit einemDurchmesser von 9,5 mm (3/8") oder stärker (nicht mitgeliefert)aufgehängt werden, die mittels (nicht mitgelieferter) ASTM A3073/8"-Rechteckmuttern (oder stärker) an einer 1-5/8...
Page 20 - Europe; Asia Pacific
LPK1 Installation Instructions Chief Manufacturing, a products divisionof Milestone AV Technologies 8800-002410 Rev00 2013 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com 05/13 USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 8...