Char-Broil 463244011 - Manual

Outdoor grilling is really quite simple. You'll succeed with burgers, dogs, or steaks usually on your very first try. With experience, you will learn how to work with your grill, creating more imaginative meals all the time. This knowledge makes up the art of grilling. Before you start grilling, org...

USDA Recommended Safe Minimum Internal Temperatures Beef, Veal, Lamb, Steaks, & Roasts 145° F Fish 145° F Pork 160° F Beef, Veal, Lamb Ground 160° F Egg Dishes 160° F Turkey, Chicken & Duck Whole,Pieces & Ground 165° F Cooking on your new grill is a hands-on experience, and it is recomme...

Why Clean? We've all heard the saying 'An ounce of prevention is worth a pound of cure'. This is great advice when it comes to keeping your grill clean. Routine Care Periodic cleaning of this grill is necessary,as grill fires can occur when grease andfood debris collect in the bottom of the grill. A...

8 • NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. • Never fill a cylinder beyond 80% full.• An over filled or improperly stored cylinder is a hazard due to possible gas release from the safety relief valve. This could cause an intense fire with risk of property ...

9 WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Tur...

10 6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. N...

11 WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. N...

12 Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW . You should see a smaller flame in LOW position than seen on HI . Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "...

13 3. Remove carryover tubes and burners. 4. 5. Carefully lift each burner up and away from valve openings. We suggest three ways to clean the burner tubes. Use the oneeasiest for you. (A) Bend a stiff wire (a light weight coat hanger works well) into a small hook. Run the hook through each burner t...

14 This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indica...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 15 Key Qty Description A 1 BOTTOM SHELF B 1 TANK SCREW , F/ BOTTOM SHELF C 2 CASTER, LOCKING D 2 CASTER, FIXED ...

2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must be on left side of bottom shelf. 7mm lock washer 7mm flat washer Locking caster Bottom shelf Non-lock caster Rear Front Lef...

3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Regulato...

6 On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. 5 1...

7 8 Insert flange on left side shelf into side shelf brackets on side of firebox. Fascia, left sideburner shelf Left sideburner shelf Flange into Brackets Bracket First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner valve bracket beneath...

9 10 Insert sideburner burner into left shelf.shelf, shown A . The stud on bottom of burner fits into rear small hole in sideburner drip pan on Secure burner to sideburner drip pan with one Wing nut, shown B . Make sure burner tube engages sideburner valve, shown C . B 21 A Sideburner burner Sidebur...

12 11 Inside of cart, insert left and right grease tray rails into slots beneath grease tray opening in upper back panel, shown A . Attach right and left rails under front brace with two #8x3/8” self-tapping screws, shown B . Insert front brace under control panel and between cart side panels. Make ...

13 14 Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. Left door Hinge pin on bottom of door Top of door PRESS Right door 23 Connect each of the wires from the main burner electrodes...

Place cooking grates onto the firebox as shown. Insert the two wire ends at rear of warming rack into holes in back of firebox. Front wires of warming rack rest on sides of firebox. 15 16 24 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposi...

On back of grill, slide grease tray into opening in upper back panel. CAUTION Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. . 17 18 25 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill ...

Unscrew on cart right side panel. Insert AA battery into ignitor, negative (—) end first. Replace the cap. electronic ignition cap – 19 26 AA Battery Electronic Ignition Cap + -

27 EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fi...

28 Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill L...

29 Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause...