CDA HCG622 - Manual - manualsarea.com

Page 2 - Important; Appliance information:

Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a...

Page 3 - Using your hob

Using your hob Fig.1 2 3 5 4 6 7 8 9 Gas burners: 1. 2. Left semi-rapid burner 1.75kW 3. Right semi-rapid burner 1.75kW1.0kW 5. Rapid burner 3.0kW Control panel: 6. Triple Ring/Rapid burner control knob7. Left Semi-Rapid burner control knob8. Right Semi-Rapid burner control knob9. Auxiliary burner c...

Page 4 - Igniting the Burners; To ignite the burners, follow these instructions:; Efficient use of your Hob; Burner Size

Igniting the Burners To ignite the burners, follow these instructions: 1. clockwise to the maximum position. Press and hold the control down to begin the ignition process (a clicking sound will be heard). 2. To turn the burner off, turn the knob clockwise past the maximum setting to the off position...

Page 5 - Correct use of the optional Wok Pan Adaptor

Correct use of the optional Wok Pan Adaptor The wok pan adaptor is a special stand that is designed to be fitted over the Triple Ring burner to give support to round bottomed woks. When using a wok, always place the wok pan adaptor in position over the pan support on the Triple Ring burner as shown ...

Page 6 - Care and Maintenance; What to do if you smell gas:; If your Hob is not working; Simmer Rating; Contact CDA Customer Care

Care and Maintenance As the hob has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of wat...

Page 7 - Mains Electricity Connection; Green

DOUBLE POLE SWITCHED FUSE SPUR OUTLET USE A 3 AMP FUSE Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a...

Page 8 - Air Vent Required (cm

Gas Supply Requirements IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY A GAS SAFE REGISTERED FITTER OR OTHER SUITABLY QUALIFIED PERSON. • This installation must comply with the Gas Safety (installation and use) Regulations 1984. • This appliance is category II2H3+ and is designed for use in the UK an...

Page 10 - Fitting the Hob; Fitting position of the hob:; Wall furniture requirements:

Fitting the Hob Unpacking the hob: Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 185mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to ...

Page 11 - How to install the hob:

How to install the hob: Overall dimensions of the hob: Width: 585mm Depth: 500mmWorktop cut-out dimensions: Width: 550mm Depth: 470mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required c...

Page 12 - Passionate about style; To contact our Customer Care Department, or for Service,

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu Passionate about style To contact our Customer Care Department, or for Service, please contact us on the details below. HCG601, HCG611, H...

CDA HCG622 - Manual

Table of Contents:

Summary

Other CDA Models