CDA CI240 - Manual

Unpacking the Washing Machine • Remove the base, corner protectors and top cover (Figure 1). Removing the Transit Bolts • Remove the screws holding the plastic covers to the back of the washing machine (Figure 2 and 3). • Loosen and remove the 3 transit bolts (Figure 3). • Cover the holes with the p...

Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 ...

Before First Use • When your washing machine has been correctly installed, we recommend that you pre-clean the machine. This is to check that the installation, the connections and the drainage are all correct, and to thoroughly clean the inside of the washing machine before any wash programmes are r...

Preparing Garments for Washing Preparation • Before placing the clothes in the drum, make sure all the pockets are empty (Figure 10). Any small objects may block the drain pump. Sorting the Clothes Sort the clothes according to fabric and how they are made: • We recommend using the delicate programm...

Detergents and Additives Your washing machine’s detergent dispenser has three compartments. • Add the detergent or additive to the detergent dispenser before starting the wash programme (Figure 14). The detergent dispenser is designed to allow the use of liquid detergents rather than adding them to ...

Selecting the Wash Programme To select a wash programme: • Turn the programme selector dial clockwise to the desired function. • The display on the control panel will light up. • Press the Start/Pause button to begin the programme. fig. 17 10 Start/Pause button Programme selector Spin/Anti-crease bu...

Selecting the Wash Programme When you select the programme, the following information will be displayed: 1. Wash programme phases: Prewash Wash Rinse Spin-drying and draining 2. Spin speed 3. Programme number (for a few seconds) and then programme duration. 4. Additional functions: Easy iron Extra r...

Washing Machine Programmes Cotton/Linen delicate colours very light soil Cotton/Linen whites/colours very light soil Cotton/Linen delicate colours light soil Cotton/Linen fast colours light soil Cotton/Linen fast colours medium soil Cotton/Linen whites heavy soil Cotton/Linen whites/fast colours hea...

Spin Speed Selection and Anti-Crease You should first select the wash programme and then select the wash options (Changing the programme cancels the preset selected options). Each selected programme has its own preset spin speed. Spin speed • You can reduce the spin speed or remove it completely by ...

Time Delay Time delay selection button • A delay of up to 24 hours can be selected. The delay must be selected after choosing the wash programme. • To select the hours of delay, press the time delay button (Figure 24). Each time the button is pressed the delayed start of washing is increased by one ...

Wash Programme Phases and Power Cuts Programme Phases • When the programme is running, the programme phase and the time remaining will appear on the display (Figure 30). • The active phases will appear successively at the top of the display as the programme progresses (Figure 30). The time remaining...

fig. 32 fig. 33 18 Maintenance • After each wash, leave the door open for a while to allow the air to circulate freely inside the machine. • From time to time, depending on the hardness of your water, it is recommendable to run a full wash cycle using a decalcifying product. This will extend the lif...

Cleaning the Filter • Clean the accessible filter if the drain pump is blocked by any foreign objects. • Open the kickplate cover with the aid of a coin and by gently pulling open (Figure 34). • Place a container under the drain pump filter to collect any water that comes out of it (Figure 35). • Re...

Problems Why doesn’t the washing machine drain or spin-dry? • If this failure is detected, F02 will appear on the display. The reasons for the F02 indicator may be the following: • The washing machine drain pump blocked, building drainage pipes blocked, or incorrect pump electrical connection. • Sol...

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu Passionate about style To contact our Customer Care Department, or for Service, please contact us on the details below.