Carrier Edge Tp NHP01 A - Installation Manual

Carrier Edge Tp NHP01 A

Carrier Edge Tp NHP01 A Thermostat – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
Page: / 68

Table of Contents:

  • Page 4 – INTRODUCTION; settings for
  • Page 5 – INSTALLATION CONSIDERATIONS; Power
  • Page 8 – INSTALLATION; UNIT DAMAGE HAZARD; CAUTION; The control assembly should be mounted before wires are attached.
  • Page 10 – AC/HP Control Location
  • Page 11 – On a section of wall without pipes or duct work.; Install AC/HP Control; ELECTRICAL OPERATION HAZARD; There may be more than 1 power disconnect.; WARNING
  • Page 12 – Failure to follow this caution may result in equipment damage or; If an existing thermostat is being replaced; ENVIRONMENTAL HAZARD; be disposed of properly.
  • Page 13 – Two- Piece Installation; NOTE; : The 2 - wire pigtail is not intended to support the weight of the User
  • Page 15 – stat mounting base matches junction box mounting holes.
  • Page 16 – HUM terminal is not used on this model.; Black is Vg
  • Page 17 – Fig. 10 - Connect Pigtail Wires to Display Module
  • Page 18 – back of the Display Module via 2 pin, keyed connector.
  • Page 20 – Module on inside equipment or a solid wall.
  • Page 21 – Fig. 14 - Cover on Equipment Control Module; — heating only system, furnace only or fan coil with electric
  • Page 22 – Single- Piece Installation
  • Page 24 – Set AC/HP Control Configuration
  • Page 26 – TO ENTER CONFIGURATION MODE
  • Page 27 – WHILE IN CONFIGURATION MODE; Configuration Options —Selection; Option 01 — Equipment Type; — operates a cool only - system. Outdoor AC unit with an
  • Page 28 – be installed for further averaging functionality. See Fig. 17
  • Page 29 – Option 06 — Cooling Lockout Below 55; On to prevent cooling below 55
  • Page 30 – C) - Outdoor temperature above which the auxiliary heat is; Option 10 — Reversing Valve
  • Page 36 – C plus the
  • Page 37 – Option 27 — Maximum Heating Setpoint; C and the maximum is 90; Option 28 — UV Light Reminder
  • Page 41 – SYSTEM START- UP AND CHECKOUT
  • Page 42 – TO TEST FAN; Final Settings; conform to the Energy Star; Table 1 – Energy Star Default Schedule
  • Page 44 – Fan; OPERATIONAL INFORMATION; Timers; Five- Minute Compressor Timeguard
  • Page 45 – Ten- Minute Staging Timer; (usually due to a large change in desired; Defrost; demand
  • Page 46 – Three- Minute Minimum on Time; A minimum difference of 1; Equipment On Indicators; auxiliary heat on; icon will be; Auto Changeover
  • Page 47 – when the thermostat is powered.
  • Page 48 – Temperature Offset After Power Cycle; TROUBLESHOOTING; Error Codes; - If the Display Module and the Equipment Control Module cannot
  • Page 50 – Table 3 – Equipment Configuration Outputs
  • Page 52 – WIRING DIAGRAMS; Fig. 18 - Display to Equipment Control Module Connection
  • Page 58 – Fig. 24 - Thermostat with Dry Contact Control for Run Time
  • Page 60 – Fig. 26 - Single- stage Furnace with Air Conditioner and Split Power
  • Page 61 – THERMOSTAT CONFIGURATION RECORD
  • Page 64 – NOTES
Loading the manual
Page 1

TP - PAC01 - A, TP - PHP01 - A

TP - NAC01 - A, TP - NHP01 - A

Performance™ Series

AC / HP Thermostat

Installation Instructions

A07049

A07048

Programmable Control

Non- Programmable Control

NOTE

: Read the entire instruction manual before starting the installation.

US patents: US7287709 B2, US20080147242 A1, USD582800 SI, US20060165149 A1, US6956463 B2.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand
Carrier
Model
Edge Tp NHP01 A
Document type
Installation Manual
Category
Thermostat
Language(s)
English
Pages
68
Format
PDF

Summary

Page 4 - INTRODUCTION; settings for

2 INTRODUCTION Carrier’s 7 - day, 5/2 - day, 1 - day programmable and non - programmablePerformance Series Thermostat Control is a wall- mounted, low - voltage temperature control in either a single unit or a two - piece unit. In two - piececonfiguration, the relays are located near the equipment an...

Page 5 - INSTALLATION CONSIDERATIONS; Power

3 INSTALLATION CONSIDERATIONS Power This control is powered by 24VAC only. It requires 24VAC (Rh and/or Rc and C terminals) of the low - voltage transformer to be connected to it for proper operation.It will not operate without these 2 connections. Rh and Rc are connected via PCBbreakout jumper. See...

Page 8 - INSTALLATION; UNIT DAMAGE HAZARD; CAUTION; The control assembly should be mounted before wires are attached.

6 INSTALLATION UNIT DAMAGE HAZARD Failure to follow the recommended wiring practices could result in damage to the wall control and personal property.Improper wiring or installation may damage AC/HP Control. Check to make sure wiring is correct before proceeding with installation or turning on power...

Ask a question

Up to 3 photos. Max 5 MB each. Formats: JPG, JPEG, PNG, WebP.

Related manuals

More Carrier Thermostats models

Other Carrier appliances