Brio CLPOU320WSLUV2P - User Manual

Page 2 - Table of Contents

2 Table of Contents Safety Information � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 3 Intended Use � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � ...

Page 3 - Safety Information

3 Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating th...

Page 5 - Package Contents

5 Indicator Panel Description 1� Power/UV self-cleaning indicator light – When illuminated, indicates that the dispenser is on. When flashing, indicates the UV self-cleaning process is on. 2� Hot water indicator light – When illuminated, indicates that the dispenser is heating water. 3� Cold water i...

Page 6 - Determine Installation Location

6 Materials Needed Wrench Installation 1� Determine Installation Location A� Place the dispenser upright. B� Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. NOTICE: Do NOT plug in the power cord until the entire installation section is complete...

Page 7 - Flush the Filters

7 3� Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A� Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. C D B� Connect the tip of the shut-off valve tube (B) to th...

Page 8 - Install the Filters and Complete the Installation

8 4� Install the Filters and Complete the Installation A� After flushing, twist each filter (D-E) clockwise into the filter housings located inside the dispenser cabinet. The sediment filter (D) goes on the left, followed by the carbon block filter. D B� Remove the safety plug from the water inlet h...

Page 9 - Operation; Turn the Dispenser On/Off; Dispense Cold Water

9 Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate th...

Page 10 - Troubleshooting; Cleaning and Maintenance

10 Troubleshooting Problem Solution The cold water is not cold. • It takes up to one hour after setup to dispense cold water. • Make sure the power cord is properly connected to a working outlet. • Make sure the back of the dispenser is at least 20 cm from a wall and there is free airflow on all 20 ...

Page 11 - Clean the Dispenser

11 Clean the Dispenser CAUTION: Before cleaning, be sure to unplug the water dispenser. IMPORTANT: This dispenser contains UV technology that automatically cycles on and off to clean your dispenser. However, if you do need to clean your dispenser for any reason, follow these steps: 1� Remove remaini...

Page 12 - Care and Maintenance

12 Filter Replacement Schedule Filter Type Model No� Replacement Schedule Function Sediment NFMPP5M 6 months or 950 gallons Performs coarse filtration of inlet water, removing sand, rust, dirt, and other suspended solids. Carbon Block NFMCTO5MS2 6 months or 950 gallons Removes chlorine and residual ...

Page 13 - Warranty

13 Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, al...

Page 14 - Contact Us