Brio CLPOU320UVF3P - User Manual

Page 2 - Table of Contents

2 Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3 - Safety Information

3 Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating th...

Page 5 - Package Contents

5 Indicator Panel Description 1 . Power/self-cleaning UV indicator light – When illuminated, indicates the dispenser is on. When blinking, indicates the self-cleaning UV process is on. 2 . Hot water indicator light – When illuminated, indicates that the dispenser is heating water. 3 . Cold water ind...

Page 6 - Installation; Determine Installation Location

6 Installation 1 . Determine Installation Location A . Place the dispenser upright. B . Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. NOTICE: Do NOT plug in the power cord until the entire installation section is completed. C . Position the b...

Page 7 - Flush the Filters

7 E . Gently tug on the tube (B) to ensure a secure connection with the feed water adapter (G). G B 3 . Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A . Connect a filter (D) to the filter housing (...

Page 8 - Install the Filters and Complete the Installation

8 4 . Install the Filters and Complete the Installation A . After flushing, twist each filter (D-F) clockwise into the filter housings located inside the dispenser cabinet. The sediment filter (D) goes on the left, followed by the pre carbon filter, then the carbon block filter. D B . Remove the saf...

Page 9 - Operation; Turn the Dispenser On/Off

9 Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate th...

Page 10 - Troubleshooting; Cleaning and Maintenance

10 Troubleshooting Problem Solution The cold water is not cold. • It takes up to one hour after setup to dispense cold water. • Make sure the power cord is properly connected to a working outlet. • Make sure the back of the dispenser is at least 20 cm from a wall and there is free airflow on all 20 ...

Page 11 - Clean the Dispenser

11 Clean the Dispenser CAUTION: Before cleaning, make sure the power switch is in the O (off) position and unplug the water dispenser. IMPORTANT: This dispenser contains UV technology that will help keep your dispenser clean. However, if you do need to clean your dispenser for any reason, follow the...

Page 13 - Care and Maintenance

13 Care and Maintenance • Keep this dispenser in a dry and cool place and avoid direct sunshine. • Ensure the back of the dispenser is at least 20 cm (8 in.) away from the wall. • Never put the dispenser on paper or foam, which may store water and then cause creepage. Never put anything flammable be...

Page 14 - Warranty

14 Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, al...

Page 16 - Contact Us