Xerox 61xx - Manuals

TABLE OF CONTENTS DOCUTECH 61XX OPERATOR GUIDE v Limitations 7-20 8. Supplies 8-1 Supplies to keep in stock 8-1 Supplies ordered from the Supply Order Representative 8-1 Supplies ordered from the Parts Marketing Representative 8-1 Ordering supplies 8-2

DocuTech 61xx Operator Guide 1-1 1. Safety notices System safety Laser safety WARNING Use of controls or adjustments, or performances other than specified herein, may result in hazardous radiation exposure. The Xerox DocuTech Models 6100, 6115, 6135, 6155, and 6180 are certified to comply with laser...

Safety notices 1-2 DocuTech 61xx Operator Guide Ozone safety This product produces ozone during normal operation. The ozone produced is dependent on copy volume and is heavier than air. Providing the proper environmental parameters as specified in the Xerox installation instructions ensures that con...

Safety notices DocuTech 61xx Operator Guide 1-3 WARNING Do not push objects into slots and openings on the system. Making contact with a voltage point or shorting out a part could result in fire or electrical shock. • If you hear unusual noises or smell strange odors, switch off the system power imm...

Safety notices DocuTech 61xx Operator Guide 1-7 Electricity at Work Regulation - UK The Electricity at Work Regulation applies only to England and Wales. The Regulation The Electricity at Work Regulation 1989 came into force in England and Wales on the 1 April 1990. This 1989 Regulation places a dut...

Safety notices 1-10 DocuTech 61xx Operator Guide Additional queries Please contact the Xerox Europe Technical Centre or your authorized Xerox representative if you have any queries regarding the information provided in this document.

DocuTech 61xx Operator Guide 2-1 2. Certifications FCC . . . USA Radio frequency This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfere...

Certifications 2-2 DocuTech 61xx Operator Guide Industry Canada requirements Notice: The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Departmen...

Certifications DocuTech 61xx Operator Guide 2-3 European Union WARNING This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Changes of modifications to this equipment not specifically approv...

DocuTech 61xx Operator Guide 3-1 3. Introduction The DocuTech 61xx Operator Guide is one of a number of publications which make up the Xerox Document Services Platform Series. About this guide The guide is intended for Xerox DocuTech 6100, 6115, 6135, 6155, or 6180 operators whose job consists of th...

Introduction 3-2 DocuTech 61xx Operator Guide Contents This section lists the contents of this guide. • Chapter 1, "System components," describes each hardware component in detail. • Chapter 2, "Routine maintenance," describes routine cleaning, maintenance, and adjustments of the Doc...

Introduction DocuTech 61xx Operator Guide 3-3 • Vertical bars–Alternatives to specified arguments are separated by vertical bars (for example, -pdl <ps | hppcl | ascii | tiff>). NOTE: Notes contain important supplemental information pertaining to the task that you should read. CAUTION CAUTION:...

DocuTech 61xx Operator Guide 4-1 4. System components The basic hardware components of the DocuTech 6100, 6115, 6135, 6155, and 6180 are the DocuSP controller and the printer. After a brief review of the process involved in electronic reprographics, this section introduces each of the system compone...

System components 4-2 DocuTech 61xx Operator Guide The DocuTech 6155 prints up to 155 prints per minute using 8.5 x 11 inch (216 x 279 mm) stock. With 17 x 11 inch (432 x 279 mm) stock, the print rate is 77 prints per minute. The DocuTech 6180 prints up to 180 prints per minute using 8.5 x 11 inch (...

System components DocuTech 61xx Operator Guide 4-3 Figure 4-1. DocuTech 6100/6115/6135 system hardware 1. Sun platform with DocuSP software 2. DocuTech 6100/6115/6135 printer 3. Processor 4. Finisher For the DocuTech 6155 and 6180, the printer consists of a processor, an interposer, and a finisher.

System components 4-4 DocuTech 61xx Operator Guide Figure 4-2. DocuTech 6155/6180 system hardware 1. Sun platform with DocuSP software 2. DocuTech 6155/6180 printer 3. Processor 4. Interposer 5. Finisher The DocuSP controller The DocuSP controller is the connection between you and the system. You co...

System components DocuTech 61xx Operator Guide 4-5 The Printer The Xerox DocuTech 6100, 6115, or 6135 printer consists of the processor, the interposer (optional), and the finisher. The Xerox DocuTech 6155 or 6180 consists of the processor, the interposer, and the finisher. These modules work togeth...

System components 4-6 DocuTech 61xx Operator Guide 8. Decurler lever 9. Dry Ink Waste container The paper trays There are three paper trays which can hold different sizes, types, and colors of stock for printing jobs. Paper tray capacities are as follows: Tray 1: 1,100 sheets of substance 20 (75 g/m...

System components DocuTech 61xx Operator Guide 4-7 The laser A laser is used to create an invisible image on the photoreceptor. The electronic master of a job communicates instructions to the laser, causing the laser to switch on and off to create the image. The fuser agent reservoir Fuser agent is ...

System components 4-8 DocuTech 61xx Operator Guide In the event of an unexpected loss of processor power, you should check the status of the ground fault protector. No red light is visible when the device is in its normal state and the power is on. When the device has tripped, a red indicator light ...

System components DocuTech 61xx Operator Guide 4-9 4. Tray 4 5. Upper exit transport 6. Tray 5 7. Lower entrance transport 8. Lower turn transport 9. Lower exit transport 10. Lower vertical transport 11. Loop transports Upper entrance transport The upper entrance transport receives the print from th...

System components DocuTech 61xx Operator Guide 4-11 Figure 4-5. Finisher components The following lists the finisher components: 1. Bindexer 2. Stitcher 3. Stacker 4. Binder 5. Binder tape reel 6. Stitcher wire spools 7. Top tray The bindexer The bindexer is a three-bin sorter that collates the page...

System components 4-12 DocuTech 61xx Operator Guide The stitcher When the job requires stitched output, the stitcher cuts and inserts the wire stitches into each print set. The stitch length is related to such factors as the number of pages in the print set and the print stock weight. A single stitc...

System components DocuTech 61xx Operator Guide 4-13 The paper paths The path that the print stock takes as it moves through the Processor and Finisher depends on the requirements of the job and if there is an Interposer. Figure 4-6. Paper path areas The numbers in figure 4-6 identify the following p...

DocuTech 61xx Operator Guide 5-1 5. Routine maintenance This chapter describes the routine activities you perform to maintain the reliability and productivity of your printer. Adding paper You can add the same kind of paper to a tray when the supply is low without stopping the printer. You must have...

Routine maintenance 5-2 DocuTech 61xx Operator Guide Figure 5-1. Preparing the paper tray NOTE: To load the paper correctly, refer to the label located on the inside panel at the front of the paper tray. Remove any damaged sheets from the top of the stack. CAUTION Do not load the paper above the red...

Routine maintenance DocuTech 61xx Operator Guide 5-3 Figure 5-2. Positioning the stack For stock outside the recommended limits, refer to the "Technical information" chapter in this guide. 8. Move the rear guide forward until it touches the edge of the stack. 9. Lower the feed belt. 10. Clos...

Routine maintenance 5-4 DocuTech 61xx Operator Guide 2. When the green "Ready to open" light comes on, pull the tray out until it stops. 3. Move the rear and side guides away from the paper stack, as shown in figure 5-3. Figure 5-3. Moving the guides NOTE: To load the paper correctly, refer ...

Routine maintenance DocuTech 61xx Operator Guide 5-5 Figure 5-4. Positioning the stack 6. Move the rear and side guides until they touch the paper stack. 7. Close the tray slowly, but firmly, until it latches. Cleaning and maintenance overview Some printer components need to be cleaned periodically ...

Routine maintenance 5-6 DocuTech 61xx Operator Guide The system uses stitcher wire from two spools located below the stacker. Stitcher spool A is used for portrait, top corner stitches. When stitcher spool A is empty, it must be replaced with a new stitcher spool. Stitcher spool B is used for portra...

Routine maintenance DocuTech 61xx Operator Guide 5-7 • Always use a drop cloth when replacing the dry ink cartridge, dry ink waste container, or when adding fuser agent. • Some parts of the system, such as the fuser, get hot during operation. To ensure that you do not burn yourself, be careful when ...

Routine maintenance 5-8 DocuTech 61xx Operator Guide WARNING A sharp edge on the plastic binder platen cleaner or on the tape spool sometimes occurs as a result of removing the cleaner. This sharp edge could cause finger cuts. CAUTION To avoid damage to the system, do not use any liquids or any abra...

Routine maintenance DocuTech 61xx Operator Guide 5-9 Figure 5-6. Binder platen cleaner b. If binder tape is in the area of the cleaner, pull the reel slightly away from the tape to avoid tape damage. c. Lift up on the cleaner and push down against the single end tab. Move the cleaner back and forth ...

Routine maintenance 5-10 DocuTech 61xx Operator Guide Figure 5-7. Cleaning the tape guides Cleaning the binder platen The following steps must be performed to clean the binder platen. 1. Use the binder platen cleaner to clean the top and side surfaces of the binder platen until all the glue is remov...

Routine maintenance DocuTech 61xx Operator Guide 5-11 Figure 5-8. Cleaning the binder platen Cleaning the flappers Using the binder platen cleaner, clean the top and side surfaces of the binder flappers until all the glue is removed.

Routine maintenance 5-12 DocuTech 61xx Operator Guide Figure 5-9. Cleaning the flappers Cleaning the calipers Using the binder platen cleaner, clean the binder caliper surfaces until all the glue is removed.

Routine maintenance DocuTech 61xx Operator Guide 5-13 Figure 5-10. Cleaning the calipers Closing the binder Perform the following steps to close the binder. 1. Push in the binder drawer until it stops. 2. Close the finisher doors. 3. Place the platen cleaner in a safe place. Maintaining the printer ...

Routine maintenance DocuTech 61xx Operator Guide 5-15 Figure 5-11. Removing the empty cartridge 4. Install a new dry ink cartridge, as shown in figures 5-12 and 5-13. a. Turn a new cartridge of dry ink upside down and shake the cartridge thoroughly to loosen the contents. b. Insert the full cartridg...

Routine maintenance 5-16 DocuTech 61xx Operator Guide Figure 5-12. Inserting and latching the cartridge d. Slide the full cartridge all the way into the system. e. Hold the cartridge in place with one hand and remove the paper seal by pulling it toward you with the other hand. Discard the seal along...

Routine maintenance DocuTech 61xx Operator Guide 5-17 NOTE: If any dry ink should get on your skin, wash with mild soap and cold water. Replacing the dry ink waste container When directed by a screen message, replace the dry ink waste container. If the dry ink waste container is not replaced, the pr...

Routine maintenance 5-18 DocuTech 61xx Operator Guide Figure 5-14. Removing the full waste container b. Remove the cap from the top of the full dry ink waste container. c. Place the removed cap over the opening on the end of the full dry ink waste container, as shown in figure 5-15. d. Do not remove...

Routine maintenance DocuTech 61xx Operator Guide 5-19 Figure 5-15. Placing the cap on the waste container e. Slide a new, empty dry ink waste container all the way into the system until the container stops, as shown in figure 5-16. Figure 5-16. Inserting the new, empty container 4. Close the process...

Routine maintenance 5-20 DocuTech 61xx Operator Guide Adding fuser agent When directed by a message, add fuser agent as soon as possible. If fuser agent is not added, the printer will stop after approximately 5,000 prints. It will not run until fuser agent is added. WARNING The fuser area can reach ...

Routine maintenance DocuTech 61xx Operator Guide 5-21 Figure 5-17. Opening the fuser drawer WARNING Fuser agent contains silicone, which can cause irritation upon contact with the eye. Make sure that you wash your hands with soap and water after you finish this procedure. 4. Fill the fuser agent res...

Routine maintenance 5-22 DocuTech 61xx Operator Guide Figure 5-18. Preparing to add fuser agent WARNING Fuser agent spills cause the floor to be slippery. If any fuser agent is spilled onto the floor, it must be removed immediately. c. Open a new box of fuser agent and remove the bottle. Remove the ...

Routine maintenance DocuTech 61xx Operator Guide 5-23 Figure 5-19. Adding the fuser agent e. Replace the reservoir cap by turning it clockwise. CAUTION Do not push the fuser agent bottle into the reservoir with excessive force. There is an anti-splash seal in the reservoir that could be damaged. f. ...

Routine maintenance 5-24 DocuTech 61xx Operator Guide Figure 5-20. Closing the fuser drawer 6. Close the processor doors. The fuser agent message will disappear after the system makes approximately 20 prints. Replacing the stitcher spool A Use this procedure to replace stitcher spool A in the system...

Routine maintenance DocuTech 61xx Operator Guide 5-25 Figure 5-21. Releasing the stitcher head 4. Remove the stitcher wire plug. a. The stitcher wire plug is located above the binder area, as shown in figure 5-22. b. Press and hold down the release clip. c. Pull the plug out of the stitcher head. Fi...

Routine maintenance 5-26 DocuTech 61xx Operator Guide • If there is no wire on the spool, use the wire cutters to pull the remaining wire carefully out of the tubing, as shown in figure 5-23. NOTE: The wire cutter tool needed to perform this procedure is located next to stitcher spool B. Figure 5-23...

Routine maintenance DocuTech 61xx Operator Guide 5-27 Figure 5-24. Rewinding the remaining wire 6. Insert the plug into the measuring bracket, as shown in figure 5-25. Figure 5-25. The measuring bracket 7. Release and remove stitcher spool A. a. Locate the green pin release handle under spool B, as ...

Routine maintenance 5-28 DocuTech 61xx Operator Guide Figure 5-26. Removing the stitcher spool pin b. Pull and hold the handle forward and remove the pin. c. Release the handle and remove stitcher spool A. 8. Install the new stitcher spool. a. Slide the new stitcher spool into position with the pape...

Routine maintenance DocuTech 61xx Operator Guide 5-29 Figure 5-27. Replacing the pin 9. Remove any damaged wire. WARNING Hold the wire on the spool to prevent eye injury and to keep the wire from unwinding. a. Locate the end of the wire on the new spool. b. Using the wire cutters, carefully clip any...

Routine maintenance 5-30 DocuTech 61xx Operator Guide Figure 5-28. Removing the paper wrapper NOTE: Hold the wire between the thumb and forefinger of both hands. 10. Feed the wire slowly into the tubing until the wire extends from the stitcher plug, as shown in figure 5-29. Figure 5-29. Feeding the ...

Routine maintenance DocuTech 61xx Operator Guide 5-31 12. Slowly and carefully pull about 3 feet (1 meter) of wire from the spool. 13. Cut the wire, leaving about 2 inches (51mm) of wire extending from the end of the stitcher plug. 14. Insert the plug into the measuring bracket. 15. Continue to feed...

Routine maintenance DocuTech 61xx Operator Guide 5-33 Refer to the procedure, Replacing the binder tape reel, in this guide for information on how to remove and replace the binder tape reel. Replacing the binder tape reel Use this procedure to replace the binder tape in the system. To ensure proper ...

Routine maintenance 5-34 DocuTech 61xx Operator Guide a. Lift the pressure roll release handle and remove the tape from the drive roll. Figure 5-33. Removing the tape b. Rewind the tape onto the tape reel. 4. Slide the tape reel off the tape reel drive. a. Move the reel retainer in the center of the...

Routine maintenance DocuTech 61xx Operator Guide 5-35 a. If necessary, rotate the tape reel slightly until it clicks into position. NOTE: The tape will not feed properly if the retainer is not locked. b. Move the reel retainer to the locked position. Figure 5-35. Locking the reel NOTE: Ensure that t...

Routine maintenance 5-36 DocuTech 61xx Operator Guide Figure 5-36. Threading the tape through the tape feeder 7. Thread the tape around the drive roll to the edge of the pressure roll. Figure 5-37. Threading the tape to the pressure roll 8. Turn the green knob clockwise until the tape extends at lea...

Routine maintenance DocuTech 61xx Operator Guide 5-37 Figure 5-38. Feeding the tape manually 9. Cut the tape. a. Lift up on the green tape cutter handle, as shown in figure 5-39. b. Remove the cut piece of tape. Figure 5-39. Cutting the tape 10. Close the binder drawer.

Routine maintenance 5-38 DocuTech 61xx Operator Guide 11. Close the finisher doors. Adjusting the binder tape registration The binder tape knob is used to align the registration of the binder tape to the top edge of a bound book. This procedure has no effect on the length of the tape, but you should...

Routine maintenance DocuTech 61xx Operator Guide 5-39 Figure 5-40. Locating the binder tape knob The knob is spring loaded and moves in increments to change the location of the binder tape. Each increment equals a change of 0.1mm, up or down, on the edge of the book. One full rotation of the knob is...

Routine maintenance 5-40 DocuTech 61xx Operator Guide Figure 5-41. Adjusting the tape position up • Pull the knob and rotate it counterclockwise to move the tape toward the bottom edge of the book. Figure 5-42. Adjusting the tape position down 8. Close the finisher doors. 9. Run a test binder job to...

Routine maintenance DocuTech 61xx Operator Guide 5-41 Adjusting the heavy paper levers This system can handle a variety of papers. Some heavier weight paper or longer paper may cause skewing problems. Adjust the heavy paper levers to prevent this skewing. Adjust the heavy paper levers when you have ...

Routine maintenance 5-42 DocuTech 61xx Operator Guide b. Lower the left and right black levers to the horizontal position, as shown in figure 5-44. Figure 5-44. Lowering the levers 7. Close the processor door. Adjusting for paper curl Each sheet of paper has a natural curve called the curl. Storing ...

Routine maintenance DocuTech 61xx Operator Guide 5-43 Figure 5-45. Measuring the paper curl 3. Place the bottom edge of the prints over the paper curl measurement chart in this guide. • If the print curl on the printed paper measures between +1 and - 2, do not change the decurler setting. • If the c...

Routine maintenance 5-46 DocuTech 61xx Operator Guide Adjusting the decurler lever Perform the following steps to adjust the decurler lever. CAUTION Do not use any paper that is not suitable for system use. 1. Open the right door of the processor. 2. Locate the decurler lever in area 7 of the paper ...

DocuTech 61xx Operator Guide 6-1 6. Problem solving The system is designed to help you find and solve problems as they happen. The system detects hardware and software problems, displays error or fault messages and screens, and sounds an alert tone (if it is enabled) when a problem needs to be corre...

Problem solving 6-2 DocuTech 61xx Operator Guide Printer faults and fault windows When the printer needs attention, it is called a fault. There are three types of faults: those that require immediate attention, those that provide information, and those that require service. Examples of faults that w...

Problem solving DocuTech 61xx Operator Guide 6-9 Clearing a binder tape fault Perform the following to clear a binder tape fault. 1. Open the finisher doors. 2. Open the top cover. WARNING The binder tape adhesive is hot, approximately 425°F (218°C). Allow the binder to cool for 5 minutes with the f...

Problem solving 6-10 DocuTech 61xx Operator Guide WARNING The binder tape adhesive is hot, approximately 425°F (218°C). Allow the binder to cool for 5 minutes with the finisher doors and top cover open before touching the binder tape. 7. If area 18 is not displayed, proceed to step 10. 8. If area 18...

Problem solving DocuTech 61xx Operator Guide 6-11 Figure 6-1. Stitcher head release handle 5. Remove the stitcher wire plug. a. The stitcher wire plug is located above the binder area, as shown in figure 6-2. b. Press and hold down the release clip. c. Pull the plug out of the stitcher head. Figure ...

Problem solving 6-12 DocuTech 61xx Operator Guide a. Using the wire cutters, slowly and carefully pull approximately 3 feet (1 meter) of wire out of the stitcher plug. b. The wire cutter tool needed to perform this procedure is located next to stitcher spool B, as shown in the lower left corner of f...

Problem solving DocuTech 61xx Operator Guide 6-13 Figure 6-4. The measuring bracket 8. Feed the wire until the wire touches the back of the measuring bracket. 9. Remove any stitcher wire fragments. a. Fold a piece of copy paper in half lengthwise. Place the folded sheet of copy paper under the stitc...

Problem solving DocuTech 61xx Operator Guide 6-15 Customer Support Center directed tasks The following tasks should be performed when a Customer Support Center Representative asks you to do so. Performing these tasks when requested may save you a visit from a Service Representative. Cleaning the pro...

Problem solving 6-16 DocuTech 61xx Operator Guide Figure 6-7. Cleaning the Q861 sensor 5. Lower the area 4 green handle. 6. Close the processor doors. Cleaning the Q1009 sensor and mirror Cleaning the Q1009 sensor and mirror should be performed only when directed by a Customer Support Center Represe...

Problem solving DocuTech 61xx Operator Guide 6-17 Figure 6-8. Q1009 sensor location 3. Clean the sensor and mirror: a. Apply a small amount of lens and mirror cleaner to a cleaning pad. b. Wipe the sensor and mirror gently with the cleaning pad. 4. Close the processor doors. Clearing or cleaning the...

Problem solving 6-18 DocuTech 61xx Operator Guide Figure 6-9. Folding the paper 2. Use the folded sheet of paper to clear any obstructions in the following sensor areas. Clearing the Q1201 sensor Clearing the Q1201 sensor should be performed only when directed by a Customer Support Center Representa...

Problem solving DocuTech 61xx Operator Guide 6-19 Figure 6-10. Locating the Q1201 sensor 3. Brush a folded sheet of paper under the sensor to clear any obstructions. 4. Close the processor cover. Clearing the Q1202 and Q1203 sensors Clearing the Q1202 and Q1203 sensors should be performed only when ...

Problem solving 6-20 DocuTech 61xx Operator Guide Figure 6-11. Locating the Q1202 and Q1203 sensors 3. Brush a folded sheet of paper under each sensor to clear any obstructions, as shown in figure 6-12. Figure 6-12. Clearing the Q1202 and Q1203 sensors 4. Close the finisher top cover.

Problem solving DocuTech 61xx Operator Guide 6-21 Cleaning the Q1222 and Q1210 sensors Cleaning the Q1222 and the Q1210 sensors should be performed only when directed by a Customer Support Center Representative. Perform the following when it is necessary to clean the Q1222 and the Q1210 sensors. 1. ...

Problem solving 6-22 DocuTech 61xx Operator Guide Figure 6-14. Locating the Q1222 and Q1210 sensors 4. Wipe each sensor gently with a soft cloth to clean them. 5. Close the finisher top cover. Clearing the Q1205, Q1206, and Q1207 sensors Clearing the Q1205, Q1206, and Q1207 sensors should be perform...

Problem solving DocuTech 61xx Operator Guide 6-23 Figure 6-15. Locating the Q1205, Q1206, and Q1207 sensors 4. Brush a folded sheet of paper across each sensor to clear any obstruction. 5. Close the bindexer and finisher doors. Clearing the Q1213 sensor Clearing the Q1213 sensor should be performed ...

Problem solving 6-24 DocuTech 61xx Operator Guide Figure 6-16. Q1213 sensor 4. Brush a folded sheet of paper across the sensor to clear any obstruction. 5. Close the binder drawer and the finisher doors. Clearing the Q1221, Q1218, and Q1227 sensors Clearing the Q1221, Q1218, and Q1227 sensors should...

Problem solving DocuTech 61xx Operator Guide 6-25 Figure 6-17. Locating the Q1221, Q1218, and Q1227 sensors Figure 6-17 shows the following sensors: 1. Q1221 sensor 2. Q1218 sensor and the sensor detector 3. Q1227 sensor and the sensor detector 3. Brush a folded sheet of paper across the sensor to c...

Problem solving DocuTech 61xx Operator Guide 6-27 Figure 6-19. Camming motor brake release 6. Release the brake release when the camming motor stops running. 7. Close the fuser drawer. a. Push in the fuser drawer until it latches into place. b. Ensure that the drawer is latched before closing the pr...

DocuTech 61xx Operator Guide 7-1 7. Technical information This section contains the hardware and software capacity guidelines for the DocuTech 6100, 6115, 6135, 6155, and 6180 systems. It includes the specifications for the printer, as well as the satisfaction guides for paper trays and stock. For c...

Technical information 7-2 DocuTech 61xx Operator Guide Heat output The tables below provide information about the heat output of the Models 6100, 6115, 6135, 6155, and 6180 printers. For further information, refer to the printer specific Installation Planning Guide. DocuTech 61xx printer specificati...

Technical information DocuTech 61xx Operator Guide 7-3 6135 print rate (per minute) 135 prints - 8.5 x 11 inch (216 x 279 mm) stock 57 prints - 17 x 11 inch (432 x 279 mm) stock Performance can be less than optimal for some unique stock sizes. For example, for stock having a process direction dimens...

Technical information 7-4 DocuTech 61xx Operator Guide Tray 2 Stock sizes US Letter (8 1/2 x 11 inches) US Legal (8 1/2 x 14 inches) 9 x 11 inches A4 8 1/2 x 13 inches 223 x 297 mm Custom (Width = 8 to 9 inches (203 to 229 mm), Length = 10 to 14 inches (254 to 356 mm)) Capacity 600 sheets, substance...

Technical information 7-6 DocuTech 61xx Operator Guide Stitcher Stock sizes 8 x 10 inches to 9 x 14 inches (203 x 254 mm to 229 x 356 mm) Capacity 2 to 70 sheets, substance 20 (75 g/m2) Stitches per spool Approximately 35,000 Binder Stock sizes 8.5 x 11 inches (216 x 279 mm) Capacity 15 sheets (7 sh...

Technical information 7-12 DocuTech 61xx Operator Guide Xerox 4024, substance 20 (75 g/m2) 3 hole drilled 4 hole drilled 7 hole drilled Load the paper into trays 1 and 2 with holes to the right; load the paper into trays 3, 4, and 5 with holes to the left. Use the Image Shift or Reduce/Enlarge optio...

Technical information DocuTech 61xx Operator Guide 7-19 Paper stock rotation This section identifies the limitations on the rotation of paper stock in the DocuTech 6xx Bypass Transport when using a third-party finishing device. Background Due to the physical limitations of the DocuTech 61xx Bypass T...

Technical information DocuTech 61xx Operator Guide 7-21 *Although the diagonal meets the 18-inch (457 mm) rotation limit, the paper stock long dimension exceeds the processor path width. The sheet must stay in the short-edge feed orientation throughout the paper path. For media sizes that are not li...

Supplies 8-2 DocuTech 61xx Operator Guide In Canada, these supplies are available through the Xerox Service Representative. Ordering supplies In the United States: Call the Supply Order Representative by dialing this toll-free number: 1-800-822-2200, Monday through Friday, between 8:00 a.m. and 5:00...