Xantech URC-2 - Manuals - manualsarea.com

Page 2 - KEYPAD DESCRIPTIONS; The following are descriptions for the various keys and LED's.; Sending & Learning IR Window

 2 URC-2 KEYPAD DESCRIPTIONS The following are descriptions for the various keys and LED's. 1 2 3 URC-2 TV VCR SAT CBL DVD TNR CD AUX POWER T/V ENTER VOL VOL CH CH PR.CH MUTE 4 5 6 7 8 9 0 PAUSE STOP REW FF INFO EXIT SEL PLAY MENU GUIDE A B C D Sending & Learning IR Window 3-Color Status LEDfor...

Page 3 - Controllers; QUICK START; Battery Cover; Teaching Single IR Commands; the selected source) under which you wish to place an IR command.

 3 Controllers URC-2 QUICK START Perform the following basic steps to begin using the URC-2 immediately. Installing Batteries 1. Turn the unit over and remove the battery cover. Press the cover Tab in the direction of the arrow on Tab and lift up. See Fig. 3. Battery Cover Tab Press in direction of...

Page 4 - Deleting Commands; Status LED; Source Key

 4 URC-2 b) If you allow more than 30 seconds to elapse between key presses, the URC-2 will automatically leave the Program Mode (enters Sleep Mode). If this occurs, simply repeat steps 3 through 5. 6. Pick another key and repeat steps 4 and 5 for all commands you wish the URC-2 to learn. 7. When f...

Page 5 - PROGRAMMING DELAYS

 5 Controllers URC-2 1 2 3 URC-2 TV VCR SAT CBL DVD TNR CD AUX POWER T/V ENTER VOL VOL CH CH PR.CH MUTE 4 5 6 7 8 9 0 PAUSE STOP REW FF INFO EXIT SEL PLAY MENU GUIDE A B C D Status LED will blink Green Press and Release the SEQ and a Source Key simultaneously to enter the Sesquence (Macro) Mode PGM...

Page 7 - Inserting a Delay; TO CLEAR

 7 Controllers URC-2 9. When stored, the Status LED will flash Amber, then go Green. You may now STEP to the next command. NOTE: You do not have to delete anything to add a new commandto the sequence. Inserting a Delay A delay may also be inserted in a similar manner. 10. Step through the sequence ...

Page 8 - • Overlay #1 is used specifically when programming, as explained; The Status LED; CLONING; PGM and XFER

 8 URC-2 CLONING When you have finished programming and have checked all commandsfor proper operation, you are now able to copy (clone) the contents toother URC-2's, if desired. This will save you the tedium of repeatedprogramming when you want identical commands in additional URC-2's.Refer to Fig....

Page 9 - ADVANCED PROGRAMMING WITH DD4 SOFTWARE

 9 Controllers URC-2 ADVANCED PROGRAMMING WITH DD4 SOFTWARE The COM Port (Fig. 13), in addition to cloning, allows the URC-2 to be programmed using Xantech's optionalDD4 Dragon Drop-IR™ system, with the ease and efficiency of your Windows ® -based PC. Complete "virtual" programming of any c...

Page 11 - The unit does not respond to any key presses.; there are some IR commands that are not learnable by the URC-2

 11 Controllers URC-2 c) On some "teaching" remotes, the internal IR emitter is considerably offset from the center of the case. Also the "learning" sensor on the URC-2 is somewhat off center as well ... it is in-line withthe SAT key LED. You may have to experiment with lateral disp...

Page 12 - SPECIFICATIONS; (Similar to Smart Pad

 12 URC-2 SPECIFICATIONS Memory: 32 kbytes SRAM (super cap. backed) IR Carrier Frequency: 31.25 kHz to 71.50 kHz Range: Up to 70’ (Depends on controlled equipment and local conditions) Number of Keys: 48 (8 Source, 40 Function) Learning System: Direct Learning or by PC with DD4 Software (optional) ...