Xantech HD44C - Manuals - manualsarea.com

Page 2 - DETAIL OVERVIEW

08905071B - 2 - DETAIL OVERVIEW [1] SOURCE LOOP-THROUGH CONNECTION The source inputs are buffered to provide an output at the same levels, assuming a 75-ohm termination is on the output. Use these connections for HD44 expansion systems. The buffers are an active circuit. The HD44 must be powered on ...

Page 4 - RS232 COMMAND STRUCTURE

08905071B - 4 - RS232 COMMAND STRUCTURE Where: {CR # } – Carriage Return (0x0D) { z# } - Zone Number. Range is 1..4 (1..16 if expanded) { s# } - Source Input Number. Range is 1..4 { 0/1 } – Either 0 (zero) or 1 (one). 0 – Off, 1 – On. NAME COMMAND RETURN REMARKS !{ z# } PR 01+ To turn on Zone 2: !2P...

Page 6 - IMPORTANT NOTICE; CIRCUIT

08905071B - 6 - [6] AC POWER INPUT Standard IEC 3-Conductor AC Line Cord Receptacle for plug-in of a 3-conducator power line cord. Be sure to note if the power receptacle is domestic (120VAC type) or international (240VAC type). [7] RS232 EXPANSION The HD44C and HD44CC5 can be expanded into a larger...

Page 8 - Installation Complete! No adjustments needed!

08905071B - 8 - QUICK INSTALLATION: HD44CC5 and HDRXSG01 [1] Connect the High-Definition Source to the HD44CC5 or HDTXSG01. Figure 1 below shows a HD44CC5 (video matrix transmitter) connected to the HDRXSG01 (receiver). [2] Using CAT5 cable, connect the HD44CC5 zone output or the output from the HDT...

Page 9 - The RC68+ should be set to Group Code “C0”.

08905071B - 9 - RC68+ (IR) COMMANDS The RC68+ should be set to Group Code “C0”. ZONE 1 ZONE 2 ZONE 3 ZONE 4 1 Zone Power Toggle 80 48 10 90 SRC 1 SRC 2 SRC 3 SRC 4 Zone 1 Source Select 00 C0 50 D0 Zone 2 Source Select 40 A0 30 B0 Zone 3 Source Select 20 E0 70 F0 2 Zone 4 Source Select 60 88 18 98 ZO...

Page 10 - FIGURE 2

08905071B - 10 - ADVANCE INSTALLATION FIGURE 2: Below shows a diagram for a sports bar application. With the equipment rack located near or behind the bar area, the coaxial outputs can be used for local HD monitors. The CAT5 outputs can be used to deliver HD content to areas such as outdoor patios a...

Page 11 - FIGURE 3

08905071B - 11 - FIGURE 3 (Note: The top unit (master unit) must be addressed as UNIT #1)

Page 12 - Several manufacturers of cable and satellite box may; Picture appears to be blooming:; A blooming picture is usually caused by a video signal that is too

08905071B - 12 - COMMON PROBLEMS AND TROUBLESHOOTING Poor video quality (picture is washed out): Several manufacturers of cable and satellite box may have higher than normal DC offset on the video signals. When connected to an HD44C, HD44CC5, and HDTXSG01, this may result in a washed out picture. To...

Page 13 - This page intentionally left blank

08905071B - 13 - This page intentionally left blank

Page 16 - Xantech Limited Warranty

Xantech Limited Warranty (Effective for products sold after July 1, 2006) Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser (“You”), its products to be free from defects in materials and workmanship for the periods specified below fro...