Xantech BXAUDIO4X4 - Manuals

Xantech BXAUDIO4X4 – Manual in PDF format online.

Manuals:

Manual

Manual Xantech BXAUDIO4X4

Summary

Page 2 - SAFETY INSTRUCTIONS - READ BEFORE OPERATING EQUIPMENT; CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

Page: 2 Model BXAUDIO4X4 © 2005 Xantech Corporation SAFETY INSTRUCTIONS - READ BEFORE OPERATING EQUIPMENT CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead sy...

Page 3 - TABLE OF CONTENTS; Section Title

Model BXAUDIO4X4 Page: 3 © 2005 Xantech Corporation TABLE OF CONTENTS Section Title Page SAFETY INSTRUCTIONS - READ BEFORE OPERATING EQUIPMENT ........................................................ 2 TABLE OF CONTENTS ...................................................................................

Page 5 - Zone Features/Specifications

Model BXAUDIO4X4 Page: 5 © 2005 Xantech Corporation CONTROLLER/AMPLIFIER FEATURES Central Processor • Four Audio Source Inputs • Current sensing (>20mA-<10A) for each input for power management of common source components and using the optional CSM1 Current Sense Module • Four source specific ...

Page 6 - Figure 1 – Front Panel; . Activ ates Program Keypad mode W hen RUN/PGM switch is set to PGM.; Power Management Button; . Enables/Disables Expansion Mode and also sets

Page: 6 Model BXAUDIO4X4 © 2005 Xantech Corporation SECTION 2.0: BXAUDIO4X4 CONTROLLER/AMPLIFIER FEATURE DESCRIPTIONS Figure 1 – Front Panel Figure 2 – The Model BXAUDIO4X4 Controller/Amplifier – Front Panel Features and Functions 1. Front Panel Cover . Snap-in panel decorativ e panel that cov ers X...

Page 7 - Button

Model BXAUDIO4X4 Page: 7 © 2005 Xantech Corporation 7. Sequence Button . Pressing the button allows a single additional IR Command to be learned creating a Sequence of Commands (also called a Macro). Up to 5 commands may be programmed in this manner making a macro of up to 6 commands in-all. 8. Dela...

Page 8 - Powers Unit ON and OFF when plugged into the proper AC Source.; Speaker Terminals; all zones. The Factory Defaults are as follows:; NOTE; power shut down or after any power interruptions.; Source Audio Inputs

Page: 8 Model BXAUDIO4X4 © 2005 Xantech Corporation 17 19 16 21 22 18 20 24 25 28 27 23 26 29 Figure 3 –Model BXAUDIO4X4 Controller/Amplifier – Rear Panel Features and Functions 16. Power ON/OFF Switch: Powers Unit ON and OFF when plugged into the proper AC Source. 17. AC Power Input . Standard IEC ...

Page 9 - other Audio/Video products to aid in the reduction of system noise.

Model BXAUDIO4X4 Page: 9 © 2005 Xantech Corporation 25. IR Out (Common) . 3.5mm Mono Mini Phone Jacks. The Control Amp has a single Common IR Output that can be used to control dev ices such as motorized drapery systems, Plasma Montior lifts and lighting systems. 26. Sense Inputs. 3.5mm Stereo Mini ...

Page 10 - SECTION 3.0: BXAUDIO4X4 LC4KP KEYPAD FEATURE DESCRIPTIONS; Figure 4 –Model LC4KP Keypad – Front Panel Features and Functions; OFF

Page: 10 Model BXAUDIO4X4 © 2005 Xantech Corporation SECTION 3.0: BXAUDIO4X4 LC4KP KEYPAD FEATURE DESCRIPTIONS 30 31 32 33 34 36 37 35 38 39 40 42 43 44 41 42 Figure 4 –Model LC4KP Keypad – Front Panel Features and Functions 30. BXAUDIO4X4 Keypad. 31. Power. Turns the zone ON and OFF. Can be program...

Page 12 - IR circuits. Slowly turn counter-clockwise to reduce sensitiv ity.

Page: 12 Model BXAUDIO4X4 © 2005 Xantech Corporation 50. Sensor Enable. Jumper. Enables IR sensor on Keypad. Remov e when using an external IR receiv er. 51. IR Sensitivity Adjustment. Carefully adjust for background light lev el to prev ent false triggering of the IR circuits. Slowly turn counter-c...

Page 14 - W hen installing Keypad next to existing J-; Figure 6: LCKP Keypad Mounting Diagram; for Typical BXAUDIO4X4 System layout:

Page: 14 Model BXAUDIO4X4 © 2005 Xantech Corporation LC4KP KEYPAD INSTALLATION INSTRUCTIONS 1. Install standard Dual-Gang J-Box or similar into wall. Note: W hen installing Keypad next to existing J- Box in wall, LCKP J-Box must be mounted 3/8” higher than any adjacent box. 2. Affix LCKP Mounting br...

Page 15 - Sense Input Connections; “PROGRAMMING POW ER MANAGEMENT”.; Zone Wiring Connections at the BXAUDIO4X4 Controller/Amplifier; connectors on the BXAUDIO4X4 as shown in; Figure 3; that could cause shorting!

Model BXAUDIO4X4 Page: 15 © 2005 Xantech Corporation component and attach the emitter to the sensor window after remov ing the protectiv e paper cov er on the flat side of the emitter head. A common IR jack is also prov ided for connection to other auxiliary dev ices. Sense Input Connections The sen...

Page 16 - Cable; Figure 6; for termination of the CAT5 cables to the RJ45 connectors.; Control Out and Status Connections; to

Page: 16 Model BXAUDIO4X4 © 2005 Xantech Corporation Wire Color Signal white/orange Tx+ orange Tx- white/green 12V RET blue IR RET white/blue IR green +12V white/brown Rx+ brown Rx- Cat 5 Cable RJ45 Connector at Controller/Amplifier RJ45 Connector at Keypad Wire Color Signal white/orange Rx+ orange ...

Page 18 - Extended Runs and Secondary Keypad In Zone; POWER; Figure 8 – BXAUDIO4X4/LC4KP Keypad CAT5 Cable Lengths; keypads in a zone, the distance to the last keypad is 200 feet (see; Figure 9 – MRCCB1 BXAUDIO4X4 Connecting Block

Page: 18 Model BXAUDIO4X4 © 2005 Xantech Corporation Extended Runs and Secondary Keypad In Zone FOUR ZONE - FOUR SOURCE AUDIO/VIDEO CONTROLLER/AMPLIFIER MRC44 1 2 3 4 POWER POWER CH CH STATUS SELECT PLAY STOP PAUSE FF REW VOL VOL MUTE POWER CH CH STATUS SELECT PLAY STOP PAUSE FF REW VOL VOL MUTE 600...

Page 19 - Speaker Connections

Model BXAUDIO4X4 Page: 19 © 2005 Xantech Corporation Speaker Connections SPEAKER PHASING: TO OBTAIN STABLE IMAGING AND FULL BASS RESPONSE, IT IS IMPERATIVE THAT STEREO SPEAKERS BE CONNECTED "IN PHASE" WITH EACH OTHER. YOU CAN VERIFY THIS AS FOLLOWS: 1. If the "+" (positiv e) and "...

Page 20 - TV; Figure 10 –Typical BXAUDIO4X4 System

Page: 20 Model BXAUDIO4X4 © 2005 Xantech Corporation TV POWER CH CH STATUS SELECT PLAY STOP PAUSE FF REW VOL VOL MUTE POWER CH CH STATUS SELECT PLAY STOP PAUSE FF REW VOL VOL MUTE ZONE 2 Primary Keypad Optional Secondary Keypad TV ZONE 1 Primary Keypad TV POWER CH CH STATUS SELECT PLAY STOP PAUSE FF...

Page 21 - SECTION 5.0: PROGRAMMING USING XPSTM Point and Shoot IR Learning; PLANNING THE SYSTEM; Confirm all functions in all zones.; ENABLE / DISABLE PROGRAM MODE; To Enable Program mode:

Model BXAUDIO4X4 Page: 21 © 2005 Xantech Corporation SECTION 5.0: PROGRAMMING USING XPS™ Point and Shoot IR Learning W hen programming the BXAUDIO4X4 System, the BXAUDIO4X4 Controller and a single LC4KP keypad plugged into the Zone 1 Keypad port are required as well as the Manufactures remotes for e...

Page 22 - Programming Button Layout

Page: 22 Model BXAUDIO4X4 © 2005 Xantech Corporation 30 31 32 33 34 36 37 35 38 39 40 42 43 44 41 42 Programming Button Layout PROGRAMMING KEYPAD BUTTONS (SINGLE COMMANDS) Note: W hen learning IR commands into the BXAUDIO4X4 Controller, make sure the IR Learning eye is free from IR interference that...

Page 23 - PROGRAMMING TIMED DELAYS

Model BXAUDIO4X4 Page: 23 © 2005 Xantech Corporation PROGRAMMING TIMED DELAYS Timed delays can be placed in-between commands in a sequence in 1 Second interv als for up to a total of 7 Seconds. After a successful IR Command has been learned; 1. Make sure the PROGRAM KEYPAD LED is GREEN and the STATU...

Page 25 - DELETING A POWER MANAGEMENT MACRO

Model BXAUDIO4X4 Page: 25 © 2005 Xantech Corporation 9. Press the proper SOURCE BUTTON [35, 36, 37, or 38] on the LC4KP Keypad for the Power Management codes to be programmed. Note: the ZONE LED’s 1 thru 4 now will represent SOURCES 1 thru 4. a. The STATUS LED [14] will turn GREEN. 10. Aim the Manuf...

Page 28 - Figure 11 – Expanded System Diagram; Press the PROGRAM KEYPAD button on the front of the BXAUDIO4X4.

Page: 28 Model BXAUDIO4X4 © 2005 Xantech Corporation Serial DB9 Male to Male Null Modem Cable I R 16VDC INPUT VIDEO AUDIO L R VIDEO AUDIO L R VIDEO AUDIO L R VIDEO AUDIO L R VIDEO AUDIO L R VIDEO AUDIO L R VIDEO AUDIO L R 1 2 3 4 5 6 OUTPUTS AV61 AUDIO VIDEO DISTRIBUTION AMPLIFIER ® 16VDC INPUT VIDE...

Page 30 - cloned with the Master data, approximately 3 1⁄2 minutes.; To Initialize the System:; process is complete and the unit is restored to Factory Default.

Page: 30 Model BXAUDIO4X4 © 2005 Xantech Corporation a. W hen the "PROGRAMMING KEYPAD" LED turns RED, release the "PROGRAMMING KEYPAD" button. 9. Power up the SLAVE unit. a. The SALVE unit will go though the normal power up sequence. b. W hen the Slav e power up sequence ends the Mas...

Page 31 - LC4KP Keypad Button Layout

Model BXAUDIO4X4 Page: 31 © 2005 Xantech Corporation SECTION 8.0: OPERATING INSTRUCTIONS W ith all system components connected and the BXAUDIO4X4 Controller and Keypads programmed, The system is ready for use. 5 2 3 1 4 9 10 6 7 8 11 12 13 14 1 5 2 3 4 67 9 10 11 12 LC4KP Keypad Button Layout MRCREM...

Page 33 - Audio

Model BXAUDIO4X4 Page: 33 © 2005 Xantech Corporation SECTION 9.0: SPECIFICATIONS Audio (ea channel) Gain (@ max VC):.................................................................................................................................. Input Ov erload: .......................................

Page 36 - XANTECH CORPORATION