Woods RBC60 LRC60 - Manuals

S a fe ty 5 RBC60/LRC60 SR (Rev. 8/26/2005) TRAINING „ Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locate y...

6 S a fe t y RBC60/LRC60 SR (Rev. 8/26/2005) (Safety Rules continued from previous page) „ Do not stop, start, or change directions sud- denly on slopes. „ Use extreme care and reduce ground speed on slopes and rough terrain. „ Watch for hidden hazards on the terrain during operation. „ Stop power u...

S a f e t y 7 MAN0169 (Rev. 5/6/2005) 1 3 4 2 1 5 5 3 4 2 CD6154C 5 - 20106 Red Reflector (2 x 4-1/2) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Rev. 8/26/2005)

8 S a fe t y MAN0169 (Rev. 5/6/2005) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 - 1002941 TO AVOID SERIOUS INJURY OR DEATH: Read Operator's Manual before operating, servicing, or repairing equipment. Follow all safety rules a...

O p e r a t i o n 9 MAN0169 (Rev. 8/26/2005) OPERATION The operator is responsible for the safe operation ofthis equipment. Operators must be instructed in and becapable of the safe operation of the equipment, itsattachments and all controls. Do not allow anyone tooperate this equipment without prop...

1 0 O p e r a t i o n MAN0169 (Rev. 8/26/2005) 3. Connect tractor top link by inserting tractor clevispin into lower hitch point on rear blade frameassembly and secure (Figure 4). Figure 3 . Lower Lift Arm Attachment, Category 0 Figure 4 . Top Link Connection Category 0 / 1 Hitch Pin Kit (Optional) ...

O p e r a t i o n 11 MAN0169 (Rev. 8/26/2005) Only offset blade when operating in light material suchas sand, loose soil, or snow. Figure 6 . Moldboard Offset Left Backfilling Reverse blade for backfilling ditches or trenches (seeReversing). The rake may also be used in light backfilling applica-tio...

1 2 O p e r a t i o n MAN0169 (Rev. 8/26/2005) PRE-OPERATION CHECK LIST (Owner’s Responsibility) ___ Review and follow all safety rules and safety decal instructions on pages 5 through 8. ___ Check that all safety decals are installed and in good condition. Replace if damaged. ___ Check that all har...

M a i n t e n a n c e 1 3 MAN0169 (Rev. 5/6/2005) MAINTENANCE The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow all safety informa-tion in this manua...

1 4 M a i n t e n a n c e MAN0169 (Rev. 5/6/2005) TAIL WHEEL ADJUSTMENT LRC60 (OPTIONAL) 1. Raise rake until tail wheels clear the ground. 2. To raise tail wheels, remove klik pin (10) andwasher (17). Allow clevis and shaft (7) to slidedown in tail wheel arm (9). Do not remove shaftcompletely from w...

A ss e mb l y 1 5 MAN0169 (Rev. 5/6/2005) ASSEMBLY INSTRUCTIONS DEALER SET-UP INSTRUCTIONS Assembly of this Rear Blade/Landscape Rake is theresponsibility of the WOODS dealer. It should be deliv-ered to the owner completely assembled, lubricatedand adjusted for normal cutting conditions. The Rear Bl...

1 6 A s s e m b l y MAN0169 (Rev. 5/6/2005) 4. Secure rear blade frame assembly to pivotassembly using pivot cap (3), two hardened flatwashers (25), and hex nuts (24). 5. Place rear blade frame assembly in desiredposition and secure with hitch pin (8). 6. Place parking stand in the down position to ...

D e a l e r C h e c k L i s ts 1 9 MAN0169 (Rev. 5/6/2005) DEALER CHECK LISTS PRE-DELIVERY CHECK LIST Inspect the equipment thoroughly after assembly toensure it is set up properly before delivering it to thecustomer. The following check lists are a reminder of points toinspect. Check off each item ...

2 0 P a rts MAN0169 (Rev. 5/6/2005) RBC60/LRC60 ASSEMBLY 1 2 3 3 4 5 6 8 9 10 11 20 22 23 24 25 24 25 25 24 26 27 28 29 30 31 25 24 CD6156B 34 - Safety Decal Set, Complete35 - Decal set LRC/RBC, Complete

P a r ts 2 1 MAN0169 (Rev. 5/6/2005) RBC60/LRC60 ASSEMBLY 1009297 MANUAL STORAGE TUBE KIT (OPTIONAL) REF PART QTY DESCRIPTION 1 1005349 1 LRC60 Tine beam 2 1005370 30 Rake tine, .31 x 1.0 3 1005354 1 Pivot cap, LRC/RBC 4 27717 1 Cutting edge, .5 x 6 x 59 5 1005352 1 Moldboard, RBC60 6 1005355 1 Pivo...

2 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual p...

A p p e n d i x 2 5 Bolt Torque & Size Charts (Rev. 8/14/02) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/ 8 1/2 5/ 8 3/4 7/ 8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 7 Metric Bolt Thread Sizes ...

F-3079 (Rev. 3/31/2010) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY All Models Except Mow’n Machine TM Zero-Turn Mowers Please Enter Information Below and Save for Future Reference....