Page 2 - i i I n t r o d u c t i o n; NOTE
i i I n t r o d u c t i o n (Rev. 11/6/2002) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructionsand safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualare comp...
Page 3 - Ta b l e o f C o n t e n t s 1; TABLE OF CONTENTS
Ta b l e o f C o n t e n t s 1 MAN0094 (11/15/2002) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INSTALLATION ...
Page 4 - S a f e t y; INSTALLATION; SAFETY RULES
2 S a f e t y BH6500/7500 SFMK (11/15/2002) _______________________________________________ INSTALLATION This Sub-Frame Mounting Kit is to be used only for the backhoes and tractors specified in the Sub-Frame Mount Installation section of this manual.Any other use or modification of this mounting ...
Page 5 - S a f e t y 3
S a f e t y 3 BH6500/7500 SFMK (11/15/2002) Remove seat and upper support assembly before installing or removing backhoe from tractor.Failure to comply may result in equipment failureand/or personal injury. If tractor is equipped with draft sensing control, set control to “HEAVY” (minimum sensit...
Page 6 - I n s t a l l a t i o n; BACKHOE SUB-FRAME INSTALLATION; DANGER
4 I n s t a l l a t i o n MAN0094 (11/15/2002) BACKHOE SUB-FRAME INSTALLATION This mounting kit is designed to provide sec ure mounting and a de qua te operator clea r-ance when properly installed. Check clearancedimensions shown in figure 1 to be sure you haveinstalled mounting kit correctly. Fol...
Page 7 - I n s t a l l a t i o n 5; SUB-FRAME INSTALLATION; Tractor Preparation; CAUTION
I n s t a l l a t i o n 5 MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Always wear relatively tight and belted cloth- ing to avoid entanglement in moving parts. Wearsturdy, rough-soled work shoes and protectivee q ui p m e n t f or e y e s , h a i r, h a n ds , h e a r i n g , a n dhead; and...
Page 8 - I n s t a l l a t i o n; Install Front Mount
6 I n s t a l l a t i o n MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Install Front Mount For Tractors with Kubota LA852 and LB702 or Woods 1009, 1012, 1016 Loaders (Figure 2) 1. Install front hanger (2) to bottom of tractorbetween right and left loader mounts using twocap screws (18) and fla...
Page 9 - I n s t a l l a t i o n 7; Install Rear Hanger Bracket
I n s t a l l a t i o n 7 MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Install Rear Hanger Bracket 1. Install rear hanger bracket (4) under tractor,between the drawbar frame (A) and the mid PTOdrive housing (B) (if equipped). 2. Position rear hanger bracket with the slots to therear of the tra...
Page 10 - I n s t a l l a t i o n; Install Rear Mount
8 I n s t a l l a t i o n MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Install Rear Mount 1. Slide rear mount (5) into slots of rear hangerbracket (4). 2. Pivot rear mount upward and secure to tractorwith clevis pins from lower lift arms (removed dur-ing tractor preparation). 4. 62977 Rear han...
Page 11 - I n s t a l l a t i o n 9
I n s t a l l a t i o n 9 MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Rotate front end of sub-frame up into the fronthanger. NOTE: Adjust front hanger as necessary to allow alignment with sub-frame. 2. Align front hanger and sub-frame. Install bent pin(7) and klik pin (16)...
Page 12 - 0 I n s t a l l a t i o n; Attach Sub-Frame to Backhoe
1 0 I n s t a l l a t i o n MAN0094 (11/15/2002) SUB-FRAME INSTALLATION Cont’d Attach Sub-Frame to Backhoe 1. Align six holes on the backhoe with holes on sub-frame. 2. Secure with six cap screws (27), hardened flatwashers (26), and hex nuts (25) as shown. 3. Tighten according to specifications give...
Page 13 - I n s t a l l a t i o n 11; HYDRAULIC INSTALLATION; WARNING
I n s t a l l a t i o n 11 MAN0094 (11/15/2002) HYDRAULIC INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety gog-gles. Hydraulic fluid under pressure can easilype ne trate s kin and will cause serious i...
Page 14 - 2 I n s t a l l a t i o n; SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR; Hydraulic System Check List
1 2 I n s t a l l a t i o n MAN0094 (11/15/2002) SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR Mount Sub-Frame & Backhoe to Tractor This mounting kit is designed to provide sec ure mounting and a de qua te operator clea r-ance when properly installed. Check clearancedimensions shown in figur...
Page 15 - I n s t a l l a t i o n 1 3; Remove Backhoe With Sub-Frame
I n s t a l l a t i o n 1 3 MAN0094 (11/15/2002) SUB-FRAME & BACKHOE REMOVAL FROM TRACTOR Remove Backhoe With Sub-Frame The only time the backhoe may be operated from a position other than the operator sea t i sduring backhoe attachment and removal. Opera-tor must • Read Sub-Frame Mounting Kit...
Page 16 - 4 I n s t a l l a t i o n; NOTES; Store Hydraulic Pump
1 4 I n s t a l l a t i o n MAN0094 (11/15/2002) SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR NOTES Store Hydraulic Pump 1. Disconnect pump (1) from tractor PTO. 2. Rotate pump and insert pin on pump mountingbracket through outside hole on foot rest asshown in Figure 16. 3. Secure pump bracket to...
Page 18 - 6 A p p e n d i x; BOLT TORQUE CHART
1 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual p...
Page 19 - A p p e n d i x 1 7; BOLT SIZE CHART; SAE Bolt Thread Sizes; ABBREVIATIONS
A p p e n d i x 1 7 Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/8 1/2 5/8 3/4 7/8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 2 3 4 5 6 7 Metric Bolt Thre...
Page 20 - WARRANTY
F-8494 (Rev.11/6/2002) Woods Equipment Company 2606 South Illinois Route 2Post Office Box 1000Oregon, Illinois 61061 815-732-2141 tel815-732-7580 fax WARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants this product to be fr...
