Woods 1013460 Manual - Free PDF Download

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n SFMK (Rev. 2/20/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualar...

Page 3 - S a f e t y; SAFETY RULES; Si no lee Ingles, pida ayuda a

S a f e t y 3 4-Point SFMK (Rev. 5/8/2006) SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! This Sub-Frame Mounting Kit is only for the backhoes and tractors specified in the Sub-FrameM o u n t I n s ta l l a t i o n s e c t i o n o f t h i s m a n u a l . A n yother use or modificat...

Page 5 - I n s ta l l a t i o n; BACKHOE SUB-FRAME INSTALLATION; Tractor Preparation; WARNING

I n s ta l l a t i o n 5 MAN0406 (Rev. 9/7/2007) BACKHOE SUB-FRAME INSTALLATION Tractor Preparation ■ Only use 1013460 4-Point Sub-Frame Mount- ing Kit for mounting Woods BH70-X, BH80-X,BH6500, BH7500 backhoe on New Holland ® T2220, TC29DA, TC33DA, TC34DA tractors orCase IH ® DX34, Farmall ® 31, Far...

Page 6 - Install Front Mounts

6 I n s ta l l a t i o n MAN0406 (Rev.9/7/2007) Install Front Mounts With Woods LS84 Loader Mount Attach front mount (32) to the right loader mountusing two cap screws (26), hardened flat washers(23) and hex nuts (27). 23. 57817 5/8 Hardened flat washer 26. 902 5/8 NC x 2 HHCS GR5 27. 230 5/8 NC Hex...

Page 7 - Install Tractor Brackets

I n s ta l l a t i o n 7 MAN0406 (Rev. 9/7/2007) Install Tractor Brackets With Woods LS84 Loader Mount 1. Place left tractor bracket (2) under left side oftractor. Use a hydraulic floor jack to help raiseand hold tractor bracket in position. 2. Attach left tractor bracket (2) to left loader mountusi...

Page 9 - Install Cross Brace; Install Offset Bars

I n s ta l l a t i o n 9 MAN0406 (Rev. 9/7/2007) Install Cross Brace 1. Remove PTO shield. 2. Attach cross brace (7) to rear of tractor using twocap screws (24) and hardened flat washers (23). 3. Attach to right and left tractor brackets using four(two per side) cap screws (18), hardened flatwashers...

Page 10 - Torque Mounting Hardware

1 0 I n s ta l l a t i o n MAN0406 (Rev.9/7/2007) Torque Mounting Hardware Attach Backhoe Mounts to Backhoe NOTE: Leave all hardware loose until backhoe has been mounted to the tractor. 1. Attach right backhoe mount (3) and left backhoemount (4) to backhoe frame. 2. Secure into position using six (t...

Page 11 - HYDRAULIC INSTALLATION; Assemble Bulkhead Bracket

I n s ta l l a t i o n 11 MAN0406 (Rev. 9/7/2007) HYDRAULIC INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety gog-gles. Hydraulic fluid under pressure can easilype ne trate s kin and will cause serious...

Page 12 - Install Hydraulic Block and Fittings; Install Hydraulic Hoses

1 2 I n s ta l l a t i o n MAN0406 (Rev.9/7/2007) Install Hydraulic Block and Fittings 1. Locate the hydraulic manifold block on the rightside of the tractor just under the fender (Figure19) and remove the block-off cap. 2. Attach hydraulic block (18) to tractor using new o-rings (14), three cap scr...

Page 13 - Install Hoses to Backhoe Valve

I n s ta l l a t i o n 1 3 MAN0406 (Rev. 9/7/2007) Install Bulkhead Adapter on Backhoe Mount 1. Attach bulkhead adapter (1) to crossmemberbetween backhoe brackets. Secure with nut sup-plied with adapter. 2. Attach elbow (10) and female quick coupler (16)to bulkhead adapter as shown in Figure 23. 3. ...

Page 14 - Mount Backhoe to Tractor; Check Hydraulic System

1 4 I n s ta l l a t i o n MAN0406 (Rev.9/7/2007) Mount Backhoe to Tractor This mounting kit is designed to provide sec ure mounting and a de qua te operator clea r-ance for most operators when properly installed.Check clearance dimensions shown below to besure you have installed seat bracket corr...

Page 16 - Remove Backhoe from Tractor

1 6 I n s ta l l a t i o n MAN0406 (Rev.9/7/2007) Remove Backhoe from Tractor The only time the backhoe may be operated from a position other than the operator seat i sduring backhoe attachment and removal. Opera-tor must: • Read Mounting Kit Manual instructions ona t ta c h i n g a n d r e m o v ...

Page 17 - STORAGE

I n s ta l l a t i o n 1 7 MAN0406 (Rev. 9/7/2007) STORAGE Connect Hydraulic Hoses TRACTOR: Connect male quick coupler on end of hose to female quick coupler at bulkhead bracketwhen backhoe is removed from tractor. See Figure28. NOTICE ■ Failure to connect hoses together will result in damage to tra...

Page 18 - P a r ts; PINCH POINT

1 8 P a r ts MAN0406 (Rev. 9/7/2007) 1013460 4-POINT SUB-FRAME MOUNTING KIT WARNING PINCH POINT Keep hands clear. 1006885 31 - PN 1006885 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. Serial Number Plate REF PART QTY DESCRIPTION 1 1013462 1 Right tractor bracket 2 1013463 1 L...

Page 20 - A p p e n d i x; BOLT TORQUE CHART

2 0 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 21 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 2 1 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 22 - WARRANTY; (Replacement Parts For All Models Except Mow’n Machine; Zero-Turn Mowers and Woods Boundary

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...