Woods LU126 - Manuals

Woods LU126 – Manual in PDF format online.

Manuals:

Manual

Manual Woods LU126

Summary

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n LMK (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sMan...

Page 3 - S a f e t y; INSTALLATION; Si no lee Ingles, pida ayuda a; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; LOADER MOUNT INSTALLATION; WARNING; CAUTION; Tractor Preparation

4 M o u n t I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) LOADER MOUNT INSTALLATION ■ Only use 111874 Loader Mounting Kit for mounting Woods LU126, LU132, 1020, 1027 loaderson New Holland ® TN55, TN60A TN65, TN70, TN70A, TN75, TN75A tractors and Case IH ® JX1060C, JX1070C, and JX1075C tractors. Any...

Page 5 - Install Right and Left Rear Mounts

M o u n t I n s ta l l a t i o n 5 MAN0041 (Rev.4/4/2008) Install Right and Left Rear Mounts 1. Attach right rear mount (1) to tractor. 2. Secure using one cap screw (7) and hardened flatwasher (9) in the top hole. 3. Secure to bottom holes using two cap screws (8)and hardened flat washers (9). 4. S...

Page 6 - Torque Hardware; Install Weather Cap on Exhaust Pipe

6 M o u n t I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) Torque Hardware Torque all hardware to specifications listed below. NOTICE ■ Check torque value of mount hardware after 10 hours of operation and again after every 50hours of operation. Install Weather Cap on Exhaust Pipe NOTE: After the hyd...

Page 7 - H y d r a u l i c I n s ta l l a t i o n; HOSE KIT INSTALLATION; General Description

H y d r a u l i c I n s ta l l a t i o n 7 MAN0041 (Rev. 4/4/2008) HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will ca...

Page 8 - Assemble and Route Hoses

8 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 58025 Hose Kit Assemble and Route Hoses 1. Attach a 90-degree elbow (2) and male quick cou-pler (3) to each loader supply hose (1). 2. Connect loader supply hoses to loader feedlinesas shown in Figure 7. 3. Route hydraulic hoses alon...

Page 9 - Connect Hoses to Tractor; Install Hose Hangers

H y d r a u l i c I n s ta l l a t i o n 9 MAN0041 (Rev. 4/4/2008) 58025 Hose Kit Connect Hoses to Tractor 1. Connect hoses to the tractor hydraulic couplersas shown in Figure 9. Figure 9 . Hose Connection to Tractor Hydraulic Couplers (Typical) Install Hose Hangers 1. Install hose hangers beneath t...

Page 10 - Verify Control Movements

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 58025 Hose Kit Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andslowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to tracto...

Page 11 - Adjust Control Valve; Install Hose Guide

H y d r a u l i c I n s ta l l a t i o n 11 MAN0041 (Rev. 4/4/2008) 46945 HOSE KIT General Description These set up instructions are for operating the 1020,1027 loader using single lever control valve mountedto the loader rear mount as shown in Figure 13. Touse this hydraulic connection the hoses mu...

Page 12 - Attach Hoses to Control Valve; Install Hydraulic Fittings and Hoses

1 2 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 46945 Hose Kit Attach Hoses to Control Valve NOTICE ■ If hydraulic lines are not connected as shown in the mount installation manual or tractor man-ual, the loader control valve may be damaged. Ablocked outlet (RETURN) or improper ...

Page 14 - Install Hose Hanger; Connect Work Port Hoses

1 4 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 46945 Hose Kit Install Hose Hanger 1. Remove lower bolt, washers, and nut thatsecures right fender to the ROPS. 2. Keep larger washer and discard the remaininghardware. 3. Attach hose hanger (9), using spacer (10), capscrew (12), f...

Page 15 - Verification of Control Movements

H y d r a u l i c I n s ta l l a t i o n 1 5 MAN0041 (Rev. 4/4/2008) 46945 Hose Kit Verification of Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andlowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses t...

Page 17 - Assemble Loader Hoses; Connect Hoses to Tractor Valve

H y d r a u l i c I n s ta l l a t i o n 1 7 MAN0041 (Rev. 4/4/2008) 1010460 Hose Kit Assemble Loader Hoses 1. Attach male half of quick coupler set (5) andelbow (2) to each of the loader feedline hoses (4).See Figure 27. 2. Attach loader feedline hoses to the steel feedlineson the loader boom. See ...

Page 19 - Install Hydraulic Fitting to Tractor Valve

H y d r a u l i c I n s ta l l a t i o n 1 9 MAN0041 (Rev. 4/4/2008) 1023577 HOSE KIT General Description These set-up instructions are for operating the LU126or LU132 loader using the tractor hydraulic remotecontrol lever. To use this hydraulic connection, thetractor must be equipped with a multi-f...

Page 22 - Assemble Hoses

2 2 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 1023584 HOSE KIT General Description These set-up instructions are for operating the LU126or LU132 loader using the tractor hydraulics. To usethis connection, the tractor must be equipped with twohydraulic levers and four tractor h...

Page 24 - Install Hydraulic Fittings to Control Valve

2 4 H y d r a u l i c I n s ta l l a t i o n MAN0041 (Rev. 4/4/2008) 1023583 HOSE KIT General Description These set up instructions are for operating the LU126or LU132 loader using single lever control valvemounted to the right loader mount as shown in Figure43. To use this hydraulic connection the ...

Page 28 - P a rts

2 8 P a rts MAN0041 (Rev. 4/4/2008) 111874 LOADER MOUNTING KIT REF PART QTY DESCRIPTION 1 1000468 1 Right rear mount 2 1000469 1 Left rear mount 3 40448 1 Grill guard kit(optional; included items 4-6) 4 40449 1 Grill guard 5 307553 8 M20 x 2.5 x 50 mm HHCS REF PART QTY DESCRIPTION 6 21531 4 M20 Lock...

Page 29 - P a r ts

P a r ts 2 9 MAN0041 (Rev. 4/4/2008) 1010460 HOSE KIT 1020, 1027 LOADERS 1023577 HOSE KIT LU126, LU132 LOADERS REF PART QTY DESCRIPTION 1 1010920 4 Adapter, M22 x 1.5 x 3/4 JICM 1 1012055 4 Adapter, M18 x 1.5 x 3/4 JICM 2 313015 4 Elbow, 3/8 NPTM x 3/8 NPTF 45° 3 315036 4 Adapter, 3/8 NPTM x 3/4 JIC...

Page 34 - A p p e n d i x; BOLT TORQUE CHART

3 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 35 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 3 5 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 36 - WARRANTY; (Replacement Parts For All Models Except Mow’n Machine; Zero-Turn Mowers and Woods Boundary

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...