Woods BH6500 - Manuals

Woods BH6500 – Manual in PDF format online.

Manuals:

Manual

Manual Woods BH6500

Summary

Page 2 - i i; NOTE

i i Introduction (2/9/01) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructionsand safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualare completed before releas...

Page 3 - Ta b l e o f C o n t e n t s 1; TABLE OF CONTENTS

Ta b l e o f C o n t e n t s 1 PN-59756 (Rev. 4/9/01) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATIO...

Page 4 - S A F E T Y; SAFETY RULES

2 S A F E T Y BH6500/7500 SFMK 11/1/00 INSTALLATION n This Sub-Frame Mounting Kit is to be used only for the backhoes and tractors specified in the Sub-Frame Mount Installation section of this manual.Any other use or modification of this mounting kitmay result in serious injury or death. n Hydraulic...

Page 5 - S A F E T Y 3

S A F E T Y 3 BH6500/7500 SFMK 11/1/00 c h e c k a n d c o m p l y w i th th e s e i n s t r u c t i o n s m a yresult in serious injury or death. n Remove seat and upper support assembly before installing or removing backhoe from tractor.Failure to comply may result in equipment failureand/or perso...

Page 6 - I n s t a l l a t i o n; BACKHOE SUB-FRAME INSTALLATION; DANGER

4 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) BACKHOE SUB-FRAME INSTALLATION n The sub-frame mount is designed to provide secure mounting and adequate operator clearancewhen properly installed. Check clearance dimen-s i o n s s h o w n i n f i g u r e 1 t o b e s u r e y o u h a v einstalled sub-...

Page 7 - I n s t a l l a t i o n 5; SUB-FRAME INSTALLATION; CAUTION

I n s t a l l a t i o n 5 PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d n If you do not understand any part of this man- ual and need assistance, see your dealer. n Always wear relatively tight and belted clothing t o a vo i d e n t a n g l e m e n t i n m ov i n g p a r t s . We a rsturdy, r...

Page 8 - I n s t a l l a t i o n

6 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Install Rear Hanger Brackets 1. Install new right and left rear hanger brackets (1, 2), using eight 10mm bolts (20) and hardened flatwashers (22). 2. Install six 10mm x 1.5P x 80mm (21) and washers (22) to secure rear han...

Page 9 - I n s t a l l a t i o n 7

I n s t a l l a t i o n 7 PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Install Mid-mount Bracket 1. Install mid-mount bracket (3) to underside of transmission housing, using cap screws (23) andwashers (29) as shown in Figure 4. NOTE: Bracket has a small notch, to be positioned on the left si...

Page 10 - I n s t a l l a t i o n

8 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Modify Loader Mounts For tractors equipped with Woods 1006 Loader Loader mounts manufactured prior to April 2001 willneed to be modified before reinforcement bracketscan be installed. Contact Woods Technical Service foras...

Page 11 - I n s t a l l a t i o n 9

I n s t a l l a t i o n 9 PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Install Crossmember 1. Attach crossmember bracket (4) to right and left reinforcement brackets, using cap screws (24) andwashers (29) as shown in Figure 9. 4. 1000581 Crossmember bracket 24. 307301 M12–1.75P x 40mm Cap sc...

Page 12 - 0 I n s t a l l a t i o n; IMPORTANT

1 0 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Insert sub-frame (1) into rear mounting bracket cradle (2 & 3). 2. Secure with clevis pins (17) and safety pins (19). 3. Pivot sub-frame up and secure to front mount (6) with bent pin (7) and Kli...

Page 13 - I n s t a l l a t i o n 11

I n s t a l l a t i o n 11 PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Attaching Sub-Frame to Backhoe 1. With sub-frame removed from tractor, attach to the backhoe using four cap screws (13), six lockwashers (14), and six nuts (15). 2. Align step (12) and insert two cap screws (7) through s...

Page 14 - 2 I n s t a l l a t i o n

1 2 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) SUB-FRAME INSTALLATION Cont’d Mount Bracket to Pump Kit NOTE: For complete information on pump kit installa- tion, consult the Woods BH6500/7500 backhoe oper-ators manual #37541. The pump mounting bracket is designed to slip overthe tractor drawbar ...

Page 15 - I n s t a l l a t i o n 1 3

I n s t a l l a t i o n 1 3 PN-59756 (Rev. 4/9/01) SUB-FRAME & BACKHOE TO TRACTOR Mount Sub-Frame & Backhoe to Tractor n The sub-frame mount is designed to provide sec ure mounting a nd ade qua te ope rator clea r-ance when properly insta lle d. Check clearanc edimensions shown in figure 1 t...

Page 16 - 4 I n s t a l l a t i o n; WARNING

1 4 I n s t a l l a t i o n PN-59756 (Rev. 4/9/01) SUB-FRAME & BACKHOE TO TRACTOR Cont’d Connect Hydraulic System n Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety gog-gles. Hydraulic fluid under pressure can e...

Page 17 - I n s t a l l a t i o n 1 5

I n s t a l l a t i o n 1 5 PN-59756 (Rev. 4/9/01) SUB-FRAME & BACKHOE to TRACTOR Cont’d Remove Backhoe With Sub-Frame n The only time the backhoe may be operated from a position other tha n the operator seat i sduring backhoe attachment and removal. Opera-tor must • Read Sub-Frame Mounting Kit ...

Page 18 - 6 P a r t s

1 6 P a r t s PN-59756 (Rev. 4/9/01) #59757 SUB-FRAME MOUNTING KIT 29 10 30 15 33 32 31 36 35 8 34 9 16 7 1 2 3 4 5 6 20 21 22 23 24 24 25 25 25 26 27 28 29 29 29 28 29 29 29 28 29 29 28 22 29 29 29 CD5888 Serial Number Plate Located inside sub-frame side rail, rear of cross tube MODEL NO. SERIAL NO...

Page 19 - P a r t s 1 7

P a r t s 1 7 PN-59756 (Rev. 4/9/01 #59757 SUB-FRAME MOUNTING KIT PARTS LIST REF PART QTY DESCRIPTION 1 1000578 1 BRACKET-REAR HANGER RT 2 1000579 1 BRACKET-REAR HANGER LT 3 1000590 1 BRACKET-MID MOUNT 4 1000581 1 BRACKET-CROSS MEMBER 5 1000594 1 BRACKET-REINFORCEMENT RT 6 1000595 1 BRACKET-REINFORC...

Page 20 - 8 A p p e n d i x; BOLT TORQUE CHART

1 8 A p p e n d i x Bolt Torque & Size Charts (Rev. 9/5/00) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual par ...

Page 21 - A p p e n d i x 1 9; BOLT SIZE CHART; ABBREVIATIONS

A p p e n d i x 1 9 Bolt Torque & Size Charts (Rev. 9/5/00) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/8 1/2 5/8 3/4 7/8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 2 3 4 5 6 7 Metric Bolt Thread ...

Page 22 - WARRANTY

F-8494 Effective 3/1/2000 (Rev. 2/14/01) Woods Equipment Company 2606 Illinois Route 2 SouthPost Office Box 1000Oregon, Illinois 61061 815-732-2141 tel815-732-7580 fax WARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants thi...