Woods 59LB-1 - Manuals

Woods 59LB-1 – Manual in PDF format online.

Manuals:

Manual

Manual Woods 59LB-1

Summary

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n Gen’l (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...

Page 3 - TABLE OF CONTENTS; Si no lee Ingles, pida ayuda a

I n t r o d u c t i o n 3 29932 (Rev. 8/10/2007) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . . ....

Page 4 - S a f e t y; TRAINING; SAFETY RULES

4 S a f e t y 59LB-1 Safety Rules (Rev. 7/9/2007) TRAINING Safety instructions are important! Read all a tta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To loc...

Page 5 - TRANSPORTATION

S a f e t y 5 59LB-1 Safety Rules (Rev. 7/9/2007) Do not stop, start, or change directions sud- denly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately u p o n s...

Page 6 - ROTATING BLADES AND; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!

6 S a f e t y 29932 (Rev. 8/10/2007) 3 - SERIAL NUMBER PLATE 1 - 25505 ROTATING BLADES AND THROWN OBJECTS Do not put hands or feet under or into mower when engine is running. Before mowing, clear area of objects that may be thrown by blade. Keep bystanders away. Keep discharge chute and guards in pl...

Page 7 - O p e r a t i o n; OPERATION; MOWING GRASS

O p e r a t i o n 7 29932 (Rev. 8/10/2007) OPERATION ■ Do not allow children or unqualified persons to operate equipment. ■ Keep bystanders away from equipment while it is in operation. ■ Stop mower and tractor immediately upon striking an obstruction. Turn off engine, removekey, inspect and repair ...

Page 8 - Lubrication; Side Shield & Discharge Chute; Optional Equipment

8 O p e r a t i o n 29932 (Rev. 8/10/2007) Figure 1 . Attitude Adjustment NOTICE ■ Improper belt alignment or tension can cause premature belt failure. Lubrication Grease caster pivot and wheel every 8 hours of opera-tion. There are grease fittings on each of the three bladespindles, which are acces...

Page 9 - Blade Servicing; HOW TO SOLVE BELT PROBLEMS

O p e r a t i o n 9 29932 (Rev. 8/10/2007) Blade Servicing Keep blades sharp for a good mowing job. Sharpenboth ends of the blade the same amount to maintainbalance. Do not sharpen blade to a razor edge, butleave a 1/16" blunt edge. Do not sharpen back side ofblade. When replacing blades, do not...

Page 10 - A s s e m b l y; ASSEMBLY

1 0 A s s e m b l y 29931 (Rev. 8/10/2007) ASSEMBLY MOWER FRAME ASSEMBLY Open box and lay parts out in an orderly manner. Side Shield (See page 20) Attach side shields (2 and 3) to mower with 3/8 x 1"bolts and flange nuts. A side discharge chute (5) maybe installed on discharge end of mower in p...

Page 11 - Lift Assembly

A s s e m b l y 11 29931 (Rev. 8/10/2007) First put belt on the bottom groove, right hand side ofthe center sheave. Then thread it to left, around the lefthand sheave. Figure 6 . Bring the belt back across the center sheave in thecenter groove over to the right outside sheave. Figure 7 . Then thread...

Page 12 - Belt Shield

1 2 A s s e m b l y 29931 (Rev. 8/10/2007) front hole of caster and deck rail; and secure with 3/8"lock washer and nut. In some cases it is necessary toopen up the end link of the chain slightly so a 3/8" boltwill pass through it. On IH184 , install 1/2 x 5/8 x 7/16 bushing (39) in tractor r...

Page 13 - A ss e mb l y

A ss e mb l y 1 3 29931 (Rev. 8/10/2007) Figure 9 . Mounting Frame Shown with 3-Point Lift Mounting Kit & 3-Point Lift Installed Figure 10 . Mounting Frame Assembly

Page 15 - NOTES

Page 16 - P a rts; MOUNTING FRAME ASSEMBLY

1 6 P a rts 29932 (Rev. 8/10/2007) MOUNTING FRAME ASSEMBLY

Page 17 - P a r ts

P a r ts 1 7 29932 (Rev. 8/10/2007) MOUNTING FRAME ASSEMBLY REF PART QTY DESCRIPTION 1 6911 2 Chain (7 link) 2 10772 2 Lift angle 3 18314 2 1/2 x 5/8 x 5/16 Sleeve 4 9814 † 1 Idler and mounting frame assembly (standard) 5 2688 6 5/32 Cotter pin 7 18440 1 Belt (special W180) 8 4336 2 Idler sheave wit...

Page 18 - SPINDLE ASSEMBLY

1 8 P a rts 29932 (Rev. 8/10/2007) SPINDLE ASSEMBLY NOTE: Repair items shaft (9) and sleeve (3) do not have a hole drilled in them for pin (4). After new partshave been assembled and proper bearing adjustmentobtained, drill a 3/16 diameter hole through sleeve andshaft. Drive in Sel-lock pin to hold ...

Page 19 - CASTERS

P a r ts 1 9 29932 (Rev. 8/10/2007) CASTERS REF PART QTY DESCRIPTION 1 29750 1 Right and left caster bundle 2 12243 1 Caster yoke (includes bolt, nut & sleeve) 3 29746 (a) 1 Right caster arm asy, 13-5/32" long -or- 3 6761 (a) 1 Right caster arm asy, 16-5/32" long 4 29747 (a) 1 Left caste...

Page 20 - MOWER FRAME ASSEMBLY

2 0 P a rts 29932 (Rev. 8/10/2007) MOWER FRAME ASSEMBLY

Page 22 - LEAF MULCHER

2 2 P a rts 29932 (Rev. 8/10/2007) LEAF MULCHER REF PART QTY DESCRIPTION A 7080 1 Leaf mulcher 1 ----- 1 Leaf mulcher weldment (if part is worn out, order a complete new leaf mulcher) 2 7076 1 Angle lug 5 23218 1 3/8 Scdl 40 pipe 5/8 long (for use on 59’s with bent down front frame) 7 839 * 3/8 NC x...

Page 23 - A p p e n d i x; BOLT TORQUE CHART

A p p e n d i x 2 3 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 24 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

2 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 25 - WARRANTY

F-3079 (Rev. 6/1/2007) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information ...

Page 26 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com ©2007 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trade...