Woods 59CL-4 - Manuals

Woods 59CL-4 – Manual in PDF format online.

Manuals:

Manual

Manual Woods 59CL-4

Summary

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n Gen’l (Rev. 2/19/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...

Page 3 - TABLE OF CONTENTS; WARNING; Si no lee Ingles, pida ayuda a

I n t r o d u c t i o n 3 29929 (Rev. 3/28/2008) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . . ....

Page 4 - S a fe t y; TRAINING; SAFETY RULES

4 S a fe t y 59CL Safety Rules (Rev. 10/12/2007) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To loc...

Page 5 - TRANSPORTATION

S a fe t y 5 59CL Safety Rules (Rev. 10/12/2007) Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately u p o n s t r i k i n g a n o b s t r u c t i o n . Tu r n o f f e n g i n ...

Page 6 - S a f e t y; ROTATING BLADES AND; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!

6 S a f e t y 29929 (Rev. 3/28/2008) 3 - SERIAL NUMBER PLATE MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 1 - PN 19007 ROTATING BLADES AND THROWN OBJECTS Do not put hands or feet under or into mower when engine is running. Before mowing, clear area of objects that may be thr...

Page 7 - TO AVOID SERIOUS; SHIELD MISSING

S a f e t y 7 29929 (Rev. 3/28/2008) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 4 - PN 18877 WARNING TO AVOID SERIOUS INJURY OR DEATH: Read Operator's Manual (available from dealer) and follow all safety precautions. Keep all s...

Page 8 - O p e r a t i o n

8 O p e r a t i o n 29929 (Rev. 3/28/2008) OPERATION & SERVICE MOWING GRASS Woods mowers are equipped with suction-type bladeswhich make them ideal for finish mowing large areas oflawn. The machine should be run level when mowing, andthe uncut area kept to the left side (right side on left-hand ...

Page 9 - MOWER SPINDLE ASSEMBLIES

O p e r a t i o n 9 29929 (Rev. 3/28/2008) MOWER SPINDLE ASSEMBLIES Mower spindles are equipped with two tapered rollerbearings. The proper adjustment is held by a springpin. It is not intended that these bearings be adjustedduring their useful life. When difficulty is experiencedwith the mower spin...

Page 10 - A s s e m b l y; ASSEMBLY; Fast Hitch; Attachment Arms

1 0 A s s e m b l y 29929 (Rev. 3/28/2008) ASSEMBLY Assembly of this mower is the responsibility of theWoods dealer. It should be delivered to the owner com-pletely assembled, lubricated, and adjusted for normalcutting conditions. Refer to mower frame assembly illustrations and partslist. Lay out pa...

Page 11 - Sheave for Belt Pulley Shaft (See page 16)

A s s e m b l y 11 29929 (Rev. 3/28/2008) cal push arms (31 and 40) and attachment brackets(32) and (39). Idler Bracket Assembly (See Figure 9 & page 16) Remove the cap screws from the PTO bearing plate.Bolt the idler bracket assembly (36, 37, 38 and 45) tothe tractor using 3/8 x 1-1/2" cap ...

Page 12 - Belt Troubleshooting

1 2 A s s e m b l y 29929 (Rev. 3/28/2008) Figure 5 . Belt Installation Proper Twist : The belt then follows with a 3/4 twist back under the left V-idler, up over the drive sheaveand back down under the right idler pulley. This willleave a 1/4 twist in the section of belt extending fromthe right V-i...

Page 13 - A ss e mb l y; Casters

A ss e mb l y 1 3 29929 (Rev. 3/28/2008) Wrong : Outer edge of belt appears to be in line. Figure 8 . Incorrect Alignment V-Belt Shield (See page 16) Place the V-belt shield (43) over the rear drive andsecure with wing nut. Casters The caster bundle includes one right and one leftcaster assembly, wh...

Page 15 - DEALER CHECK LISTS; PRE-DELIVERY CHECK LIST; DELIVERY CHECK

A ss e mb l y 1 5 29929 (Rev. 3/28/2008) DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly toensure it is set up properly before delivering it to thecustomer. The following check lists are a reminder ofpoints to inspect. Check off ea...

Page 16 - P a rts

1 6 P a rts 29929 (Rev. 3/28/2008) 59CL-4 & 59CLF-4 MAIN ASSEMBLY 53 - COMPLETE DECAL SET61 - FRENCH SAFETY DECAL SET

Page 17 - P a r ts

P a r ts 1 7 29929 (Rev. 3/28/2008) 59CL-4 & 59CLF-4 MAIN ASSEMBLY NOTE: Mower frames sold after 1976 the front side of mower is formed down. Before they had a bolt-on front shield. Key For Number Used Columns A Serial Number 100 through 306 (59CL-1) C Serial Number 479 through 822 (59CL-3 &...

Page 19 - SPINDLE ASSEMBLY

P a r ts 1 9 29929 (Rev. 3/28/2008) SPINDLE ASSEMBLY NOTE : When difficulty is experienced with a mower spindle, time and trouble will be savedby buying a complete new assembly. NOTE : Repair shaft (9) and repair sleeve (3) do not have a hole drilled in them for pin (4). Afternew parts have been ass...

Page 21 - LEAF MULCHER

P a r ts 2 1 29929 (Rev. 3/28/2008) LEAF MULCHER REF PART QTY DESCRIPTION A 7080 1 Model 59 Leaf mulcher -or- A 13482 1 Model L306 Leaf mulcher 1 ----- 1 Leaf mulcher weldment 2 7076 1 Angle lug 5 23218 1 3/8 Schd 40 pipe 5/8 long 7 839 * 3/8 NC x 1 HHCS GR5 8 979 * 3/8 NC x 1-1/2 HHCS GR5 9 565 * 3...

Page 22 - A p p e n d i x; BOLT TORQUE CHART

2 2 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 23 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 2 3 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 24 - WARRANTY

F-3079 (Rev. 4/4/2008) WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): ___________________________________________ Model Num...

Page 25 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...