Woods 2300003 - Manuals - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n LMK (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sMan...

Page 3 - S a f e t y; INSTALLATION; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; LOADER MOUNT INSTALLATION; TRACTOR PREPARATION; WARNING; Remove Exhaust Bracket; Washer

4 M o u n t I n s ta l l a t i o n MAN0572 (Rev. 1/30/2009) LOADER MOUNT INSTALLATION TRACTOR PREPARATION ■ Only use this mounting kit for mounting Woods LU132 or LU132-2 loader on Case IH ® JX1085C and JX1095C or New Holland ® TN85A, TN95A, TN85DA, TN95DA tractors. Any other use or modification oft...

Page 5 - Install Right Mount; Install Left Mount

M o u n t I n s ta l l a t i o n 5 MAN0572 (Rev. 1/30/2009) Install Right Mount 1. Attach right mount (1) to tractor chassis andframe using four hex flange screws (7) andNord-Lock washers (9). 2. Attach to tractor frame using two cap screws (4)and hardened flat washers (8). 3. Torque hardware to: M1...

Page 8 - H y d r a u l i c I n s ta l l a t i o n; General Description

8 H y d r a u l i c I n s ta l l a t i o n MAN0572 (Rev. 1/30/2009) 1018219 & 1023597 HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily pe...

Page 9 - Install Hydraulic Fittings

H y d r a u l i c I n s ta l l a t i o n 9 MAN0572 (Rev. 1/30/2009) Install Hydraulic Fittings 1. Locate the control valve under the right side ofthe operator platform/cab and remove the fourplugs from the valve work ports. 2. Install two adapters (2), elbows (6), and femalehalf of quick coupler set...

Page 10 - Assemble Hoses

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0572 (Rev. 1/30/2009) Assemble Hoses 1. Attach male half of quick coupler set (4), coloredbands (10 & 11), and dust caps (8) to the end oftwo loader supply hoses (1). See Figure 14. 2. Attach male half of quick coupler set (4), elbow(5), colored ba...

Page 11 - Verify Control Movements

H y d r a u l i c I n s ta l l a t i o n 11 MAN0572 (Rev. 1/30/2009) Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andslowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to tractor controlvalve ...

Page 12 - P a rts

1 2 P a rts MAN0572 (11/10/2006) 2300003 LOADER MOUNTING KIT 2300003 LMK 1018190 Grill Guard REF PART QTY DESCRIPTION 1 1023010 1 Right mount 2 1023011 1 Left mount 3 1018180 2 Oscillation stop 4 1024088 4 M20 x 2.5P x 100 mm HHCS CL10.9 5 1001377 2 M20 x 2.5P x 40 mm HHCS CL10.9 6 1028719 4 M14 x 2...

Page 13 - P a r ts

P a r ts 1 3 MAN0572 (11/10/2006) 1018219 & 1023597 HOSE KIT REF PART QTY DESCRIPTION 1 1023473 4 Hose, 125" x 1/2 NPTM x 3/4 JICM (1023597 Hose Kit) 1 1002878 4 Hose, 74" x 1/2 NPTM x 3/4 JICM (1018219 Hose Kit) 2 1012055 4 Adapter, M18 x 1.5M x 3/4 JICM 3 1020934 1 Hose guide 4 26124 4...

Page 15 - A p p e n d i x; BOLT TORQUE CHART

A p p e n d i x 1 5 Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual ...

Page 16 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

1 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG ............................................................ Agriculture ATF ................

Page 17 - WARRANTY

F-3079 (Rev 11/24/2008) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Informa...

Page 18 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) ©2006 Woods Equipment Company. All rights reserved. WOODS, and the Woods logo are trademarks of Woods Equipment Company. All othertrademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respectivecomp...