Woods 211718 - Manuals

Woods 211718 – Manual in PDF format online.

Manuals:

Manual

Manual Woods 211718

Summary

Page 2 - I n t r o d u c t i o n; DANGER

2 I n t r o d u c t i o n LMK (Rev. 6/6/2005) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sManu...

Page 3 - S a f e t y; INSTALLATION; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; WARNING; CAUTION; Tractor Preparation

4 M o u n t I n s ta l l a t i o n MAN0530 (6/30/2006) 211718 LOADER MOUNTING KIT ■ Only use 211718 Loader Mounting Kit for mounting Woods 1009 and 1012 loaders on Mahin-dra ® 2815 and 3215 tractors. Any other use or mod- ification of these mounting kits may result inserious injury or death. Safet...

Page 5 - Install Right and Left Rear Mounts

M o u n t I n s ta l l a t i o n 5 MAN0530 (6/30/2006) Install Right and Left Rear Mounts 1. Using a lifting device, align right mount (1) withholes on tractor mounting pad. 2. Secure right mount to mounting pad using fourcap screws (11) and hardened flat washers (13).See Figure 1 and Figure 2. 3. S...

Page 6 - Install Rear Axle Plates; Install Rear Rails

6 M o u n t I n s ta l l a t i o n MAN0530 (6/30/2006) Install Rear Axle Plates 1. Remove three bolts from lower axle housing. 2. Place axle plate (4) over axle housing and secureusing two cap screws (8) and hardened flat wash-ers (14) in the middle and rear holes. 3. Install cap screw (9) and harde...

Page 7 - Install Cross Brace

M o u n t I n s ta l l a t i o n 7 MAN0530 (6/30/2006) Install Cross Brace 1. Place cross brace (3) between right (5) and left(6) rear rails and right (1) and left (2) rear mounts. 2. Secure parts together using six cap screws (10)(three per side), hardened flat washers (13), andhex nuts (15). Figur...

Page 8 - Torque Hardware

8 M o u n t I n s ta l l a t i o n MAN0530 (6/30/2006) Torque Hardware Torque hardware to specifications listed below. Install Grill Guard (Optional) 1. Align grill guard (16) with holes on front of tractorframe and secure into position using four capscrews (A) and hardened flat washers (B). 2. Torq...

Page 9 - H y d r a u l i c I n s ta l l a t i o n; General Description

H y d r a u l i c I n s ta l l a t i o n 9 MAN0530 (6/30/2006) 1014620 HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and wil...

Page 10 - Install Hydraulic Fittings to Tractor

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0530 (6/30/2006) Install Hydraulic Fittings to Tractor IMPORTANT ■ Incorrect installation can damage tractor hydraulic system. Read and understandinstructions in tractor manual before connecting. 1. Locate the hydraulic manifold block on the rightside ...

Page 11 - Connect Hydraulic Hoses

H y d r a u l i c I n s ta l l a t i o n 11 MAN0530 (6/30/2006) Connect Hydraulic Hoses 1. Remove hydraulic fitting from the PBY port on thecontrol valve. 2. Install elbow (4) into PBY port. 3. Connect end of hose (1) to the IN, OUT and PBYports on the control valve. 4. Route hoses along inside righ...

Page 12 - Connect Work Port Hoses

1 2 H y d r a u l i c I n s ta l l a t i o n MAN0530 (6/30/2006) Connect Work Port Hoses 1. The control valve kit contains hoses assembledwith quick couplers. Attach the hoses to loaderfeedlines, following the color scheme shown inFigure 20. 2. Connect loader feed hoses to control valvehydraulic cou...

Page 13 - P a r ts

P a r ts 1 3 MAN0530 (6/30/2006) 211718 LOADER MOUNTING KIT REF PART QTY DESCRIPTION 1 1020638 1 Right rear mount 2 1020639 1 Left rear mount 3 1020646 1 Cross brace 4 1020649 2 Rear axle plate 5 1020650 1 Right rear rail 6 1020651 1 Left rear rail 7 1020669 8 M14 x 1.5P x 110 mm HHCS CL8.8 8 307309...

Page 14 - P a rts

1 4 P a rts MAN0530 (6/30/2006) 1014620 HOSE KIT REF PART QTY DESCRIPTION 1 1014619 3 Hose, 36" x 9/16 JICF x 9/16 JICF 2 315045 3 Adapter, 3/8 BSPTM x 3/8 NPTF 3 44552 3 Elbow, 3/8 NPTM x 9/16 JICM 45° 4 63558 1 Elbow, 9/16 JICM x 9/16 ORBM 90°(not shown)

Page 15 - A p p e n d i x; BOLT TORQUE CHART

A p p e n d i x 1 5 Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual ...

Page 16 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

1 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG ............................................................ Agriculture ATF ................

Page 17 - WARRANTY

F-3079 (Rev. 5/2/2006) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information ...

Page 18 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) ©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of WoodsEquipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual a...