Woods 211716 - Manuals - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n LMK (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sMan...

Page 3 - S a f e t y; INSTALLATION; SAFETY RULES

Loader Mounting Kit SR3 (11/1/2002) 3 S a f e t y INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in this...

Page 4 - M o u n t I n s ta l l a t i o n; Tractor Preparation; IMPORTANT; Remove Hydraulic Coupler Bracket; WARNING

4 M o u n t I n s ta l l a t i o n MAN0426 (3/3/2006) 211716 LOADER MOUNTING KIT Tractor Preparation ■ Only use 211716 Loader Mounting Kit for mounting Woods 1009, 1012, LC96 and LC102loaders on John Deere ® 3120, 3320, 3520, 3720 & 3203 FWA ROPS tractors. Any other use or modi-fication of this ...

Page 5 - Install Coupler and Hose Line Brackets; Install Right and Left Rear Mounts

M o u n t I n s ta l l a t i o n 5 MAN0426 (3/3/2006) Install Coupler and Hose Line Brackets 1. Insert hydraulic couplers through new couplerbracket (2) and secure with snap rings. NOTE: Make sure hydraulic couplers are in the same color sequence as they were when theywere removed. 2. Connect couple...

Page 6 - Install Right and Left Front Mounts; Install Side Rails

6 M o u n t I n s ta l l a t i o n MAN0426 (3/3/2006) Install Right and Left Front Mounts 1. Install right (4) and left front mounts (5) to front oftractor using eight (four per side) cap screws (7),flat washers (10), and hex nuts (8). 2. Position cap screws on the outside of mount withflat washers ...

Page 7 - Torque Hardware

M o u n t I n s ta l l a t i o n 7 MAN0426 (3/3/2006) Torque Hardware Torque all mounting hardware to specifications givenbelow. Install Grill Guard (Optional) 1. Align grill guard (A) with holes on front of tractorframe and secure into position using four capscrews (B), hardened flat washers (D), a...

Page 8 - H y d r a u l i c I n s ta l l a t i o n; General Description; Assemble Hoses

8 H y d r a u l i c I n s ta l l a t i o n MAN0426 (3/3/2006) 1019027 HOSE KIT INSTALLATION General Description These instructions are for operating the loader usingthe tractor hydraulic remote control lever. To use thishydraulic connection, the tractor must be equippedwith the manufacturer’s multi-...

Page 9 - Connect Hoses to Tractor

H y d r a u l i c I n s ta l l a t i o n 9 MAN0426 (3/3/2006) Connect Hoses to Tractor 1. Connect hydraulic hoses to tractor hydrauliccouplers as shown in Figure 12. 2. Attach color coded plastic bands around malequick couplers to identify quick couplerconnections. Figure 12 . Hydraulic Hose Connect...

Page 10 - P a rts

1 0 P a rts MAN0426 (3/3/2006) 211716 LOADER MOUNTING KIT 1019012 Grill Guard (Optional) REF PART QTY DESCRIPTION 1 1019010 1 Right rear mount 2 1019011 1 Left rear mount 3 1019013 2 Side rail 4 1034180 1 Right front mount 5 1034181 1 Left front mount 6 230 * 10 5/8 NC Hex nut 7 307301 8 M12 x 1.75P...

Page 12 - A p p e n d i x; BOLT TORQUE CHART

1 2 A p p e n d i x Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual ...

Page 13 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 1 3 Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG ............................................................. Agriculture ATF ...............

Page 14 - WARRANTY; (Replacement Parts For All Models Except Mow’n Machine; Zero-Turn Mowers and Woods Boundary

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...

Page 16 - PART NUMBER

PART NUMBER MAN0426 ©2006 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of WoodsEquipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manualare th...