Page 2 - Loader Mounting Kit Model:; CAUTION
PN-53661 (Rev. 12/96) ii TO THE DEALER: The loader mounting kit and/or hydraulic hose kit assembly and proper installation to the tractor is the responsibility of the DuAl dealer. Read manual instructions and safety rules. Make sure all items on the Pre-Delivery and Delivery Check Lists in the loade...
Page 3 - SAFETY RULES; FALLING HAZARD; CRUSHING HAZARD; TO AVOID INJURY; DANGER; FALLING LOAD HAZARD; WARNING; DANGER
1 PN-53661 (Rev. 12/96) SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! FALLING HAZARD TO AVOID INJURY OR DEATH: D DO NOT WORK FROM OR ALLOW RIDERS ON LOADER OR ITS ATTACHMENTS. 26-0350 CRUSHING HAZARD TO AVOID INJURY OR DEATH: D DO NOT WALK OR WORK UNDERNEATH A RAISED LOADER. D LOWER...
Page 4 - INSTALLATION
2 PN-53661 (Rev. 12/96) SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator.In addition to the design an...
Page 5 - OPERATIONAL SAFETY; NOTES
3 PN-53661 (Rev. 12/96) SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) J Ensure shields and guards are proper- ly installed and in good condition. Replace if damaged. OPERATIONAL SAFETY J Protective sleeves must be over hydrau- lic hoses an...
Page 6 - BOLT SIZE CHART; IN; SAE Bolt Thread Sizes; ABBREVIATIONS
4 PN-53661 (Rev. 12/96) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and Metric Bolts. 8MM 10MM 12MM 14MM 16MM 18MM 175 150 125 100 75 50 25 IN MM 1 7 6 5 4 3 2 7/8 3/4 5/8 1/2 3/8 5/16 SAE Bolt Thread Sizes Metric Bolt Thread Sizes ABBRE...
Page 7 - BOLT TORQUE CHART
5 PN-53661 (Rev. 12/96) BOLT TORQUE CHART After every ten (10) hours of operation, check all hardware and tighten where required. SAE Series Torque Chart DO NOT use these values if a different torque value or tightening procedure is listed for a specific application. Torque values listed are for gen...
Page 8 - MOUNTING INSTRUCTIONS
6 PN-53661 (Rev. 12/96) MOUNTING INSTRUCTIONS Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator.In addition to the design and configuration of equipment, hazard cont...
Page 9 - Crossmember Link Attachment
7 PN-53661 (Rev. 12/96) To provide clearance for mounting the 215 loader, adjust the front tractor tires to a minimum 67” tread or to the manufacturer’s widest recommended setting. This also provides increased tractor stability. SC686 67” MINI- MUM Figure 3 . Tire Adjustment -- 215 Loader Only Rear ...
Page 10 - Hydraulic Hose Installation Instructions
8 PN-53661 (Rev. 12/96) Hydraulic Hose Installation Instructions WARNING J Keep hands and body away from pres- surized lines. Use paper or cardboard, not body parts to check for leaks. Wear safety goggles. Hydraulic fluid (oil) under pres- sure will easily penetrate skin and can cause serious injury...
Page 13 - LOADER VALVE FUNCTION CHART
11 PN-53661 (Rev. 12/96) #199758 HYDRAULIC HOSE KIT 195 LOADER D C B A 3 2 1 215 LOADER BA D C D C B A CD4943 Ref Part No No No Used Description 1 53670 4 Hose -- 3/8, 150”, 3/4 JICM x 3/4 JICM with vinyl protector 2 31-3053 4 90 ° Swivel elbow 3 66511 4 Quick coupler -- male Items Not Shown Part No...
Page 15 - WARRANTY; Please enter information below and; SAVE FOR FUTURE REFERENCE.
F-3079 (Rev. 4/96) STD Woods Equipment Company 2606 Illinois Route 2 South Post Office Box 1000 Oregon, Illinois 61061815-732-2141 tel 815-732-7580 fax WARRANTY Date Purchased: From (Dealer): Model Number: Serial Number: Please enter information below and SAVE FOR FUTURE REFERENCE. WOODS warrants ea...
Page 16 - PART NUMBER
PART NUMBER 53661 Woods Equipment Company 2606 Illinois Route 2 South Post Office Box 1000 Oregon, Illinois 61061815-732-2141 tel 815-732-7580 fax LITHO IN USA