Page 2 - VERY SLOWLY; OPERATION; TUNING ANTENNA FOR THE BEST PICTURE
2 FINDING THE SATELLITE STEP 1 . Step outside the vehicle and, using a compass, determine which direction is North. (Standing in or nearthe vehicle can give you an incorrect reading.) The moreaccurately you determine North, the easier it will be tofind the satellite(s). STEP 2. Using satellite recei...
Page 3 - OPERATIONS DO’S AND DON’T’S; DO’S; Do lower antenna before moving vehicle.; DON’T’S; Don’t move RV/Coach with the antenna in the UP; FIGURE 1
3 OPERATIONS DO’S AND DON’T’S DO’S 1. Do check parking location for obstructions beforeraising antenna.2. Do carefully raise, lower and rotate the antenna — ifdifficult, check for cause.3. Do rotate slowly when searching for the satellite(s)and check fine tuning on TV set for proper adjustment.4. Do...
Page 4 - TROUBLE SHOOTING; NO PICTURE ON TV; FIGURE 3; WARRANTY REPAIR WORK; or receiver warranty, refer to the receiver; ORDERING REPAIR PARTS; Reflector at 90°; Signal from satellite; LNBF
4 TROUBLE SHOOTING NO PICTURE ON TV 1. Do you have a clear line of sight to the satellite? Arethere trees, buildings, etc. in the way? Figure 3 illus-trates the look angle of your reflector.2. Do you have the menu from the receiver? If not, checkthe channel the TV set is tuned for — it should be 3 o...
Page 5 - INSTALLATION AND ASSEMBLY; THINGS YOU NEED; Mount; FIGURE 5
5 INSTALLATION AND ASSEMBLY THINGS YOU NEED Screwdrivers (Phillips and slot)1-3/4” hole saw7/16” wrench Drill with 1/8” bitTape measure Sealant (Must be approved for compatibility w/roof) STEP 1. Choose a location on the roof for the unit. The dish must be able to rotate without interfering with oth...
Page 6 - FIGURE 6
6 STEP 3. Remove backing from gasket. Attach adhesive side to base plate. IF YOU ARE USINGTHE ROOF WEDGE (RW-5000), use 3/16” gasketincluded with the mount UNDER the roof wedge.Install the 1/16” gasket included withRW-5000 BETWEEN the mountand roof wedge.See Figure 7. The word FRONT isembossed on th...
Page 7 - FIGURE 9
7 STEP 7. Facing the front of the dish, find coax cables attached to side of the feed arm, Figure 9. Measure 24”of coax from this point and mark. DO NOT CUT. Rotatemount on base clockwise, fully, until it stops. Routecoax around mount base, Figure 10.Fasten cable clamp in hole in mount base (check r...
Page 8 - DIGITAL ELEVATION SENSOR ROOF CONNECTIONS; and; INSIDE YOUR RV
8 FOR RM-DM61/RM-DM55 ONLY DIGITAL ELEVATION SENSOR ROOF CONNECTIONS The illustrations below show the different methods of connecting wires at roof level. Method will depend on model. Wirecolors MUST MATCH (i.e. red to red, green to green, black to black, white to white). This wire harness connects ...
Page 10 - Tighten screw snugly
10 RotationClamp ASSEMBLED VIEW POINT TO BACK OF RV POINTERMUST POINTTO REDSCREW ONROTATIONCLAMPWHEN INTRAVELPOSITION CAUTION: After INITIALINSTALLATION, theantenna should ROTATEAPPROXIMATELY 360°FROM TRAVEL POSITION.The pointer on theDIRECTIONAL HANDLEshould point towards theRED SCREW on theROTATIO...
Page 11 - EXPLODED PARTS VIEW
11 EXPLODED PARTS VIEW Antenna Head Dish Frame 46 cm Reflector White (4) Flat Head Bolt s (White) LB-1000: S tandard Single LNBF E-Clip Top Boom Carriage Bolt Pin 1-9/16” long Mount Adapter Rubber Bumper Screw Bushing Bottom Boom Flange Nut 1/4-20 Feed Arm Roller Hex Head Bolt 1/4-20 x 2.5” Nylock N...
Page 12 - PARTS LIST
12 NOT TO SCALE Ceiling Base Directional Dial (4) #10 Phillips FlatHead Screws Directional Handle Azimuth Lock Azimuth Lock Knob Washer #10 x 3/8"Red PhillipsScrew #8-32 Square Nut Crank Handle Base Crank Handle Knob Washer #8-32 x 3/8"Phillips Screw #10 x 3/8" Phillips Screw Directional...
Page 13 - SPECIFICATIONS; and ExpressVu; ANTENNA/LIFT/LNBF TWO YEAR LIMITED WARRANTY
13 SPECIFICATIONS Height when raised ........ 30” with satellite antenna in vertical position Height in travel position ........ 8” Operating radius ........ 35” (70” diameter circle) Roof space required ........ 19.5” x 46.75” LNBF ........ Compatible with DISH Network ® , DirecTV ® and ExpressVu C...
Page 14 - REPLACEMENT PARTS KITS; HEAD ASSEMBLY RP-RS00; RD MODELS
14 REPLACEMENT PARTS KITS HEAD ASSEMBLY RP-RS00 Head w/bracket and nut ................ 1Pins .............................................. 2E-Clip ............................................ 2 REFLECTOR RP-REFL Dish .............................................. 1Bolt ...............................