Wagner 580678 - Manuals

EN 5 IMPORTANT SAFETY INFORMATION GENERAL INFORMATION WARNING: HAZARDOUS VAPORS Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with the body. Vapors can cause severe nausea, fainting, or poisoning. PREVENTION: • Use a respirator or mask if vapors can...

1 2 PARTS AND COMPONENTS 6 EN PRIME k SPRAY p Spray hose port Tank Inlet filter (A) ON/OFF switch Tank lid Material return tube PRIME/SPRAY knob (B) The PRIME/SPRAY knob can be turned in either direction to desired setting (vertical = PRIME, horizontal = SPRAY ) . Spray gun Spray tip Tip guard a b W...

LOCKED HANDLE 1 0 2 k 3 4 EN 7 BEFORE YOU BEGIN i This section contains instructions that will be repeated throughout this manual. Read and understand this section before using the equipment. SPRAY GUN TRIGGER LOCK Engage the trigger lock whenever instructed. The gun is locked when the trigger lock ...

1 PUSH 2 3 k 0 4 A 5 B 0 8 EN LOAD MATERIAL i These steps will prime the system and get it ready to spray.www.wagnercontrolpro.com/howtoCP130 YOU WILL NEED • The material you plan to spray • Extension cord • Waste bucket i Recommendation: It is good practice to perform the steps on this page using w...

1 2 0 p 3 4 k PAGE 7 5 a b a b OR 6 OR 7 OR 8 p 0 EN 9 SPRAYING i Follow these steps to deliver spray material from the tank to the spray gun. YOU WILL NEED • Waste bucket • Scrap material / cardboard • Drop cloths to protect floors and furnishings from overspray 1. Make sure the tip and spray guard...

CORRECT INCORRECT 10” - 12” (25 - 30 cm) CORRECT 10” - 12” (25 - 30 cm) INCORRECT Start stroke End stroke Pull trigger Release trigger Move steadily i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, follow any or all the procedures listed on pages 11-1...

1 2 3 p 4 EN 11 SPRAYING TROUBLESHOOTING - CLEAR THE SPRAY TIP i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. Follow the steps below. YOU WILL NEED • Scrap material / cardboard Do not attempt to unclog or clean the ti...

1 k PAGE 7 2 3 4 12 EN SPRAYING TROUBLESHOOTING - CLEAN THE INLET FILTER i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the inlet filter could be clogged. Follow the steps below. YOU WILL NEED • Warm, soapy water for latex material • Mineral spirits...

1 k PAGE 7 2 AND 3 4 AND 5 6 PAGE 9 EN 13 i This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow Cleanup instructions, pages 14-15. YOU WILL NEED • Water • Plastic bag • Damp rags • Stir stick i Instruction...

1 k PAGE 7 2 3 4 5 0 p 14 EN CLEANUP CLEANING NOTES - READ BEFORE CLEANING • When using latex material, clean sprayer and components with warm, soapy water. For oil based material use mineral spirits. Never use mineral spirits with latex materials. • NEVER use gasoline to clean sprayer. • Dispose of...

1 2 a 3 HOUSEHOLD OIL 4 5 HOUSEHOLD OIL 6 0 7 16 EN LONG TERM STORAGE i Follow these steps to prepare your sprayer for long- term storage. YOU WILL NEED • Light household oil (such as 10W30 motor oil or vegetable oil for example) / All Guard • Rags • Two adjustable wrenches 1. Pull trigger guard fro...

1 1 23 6 4 5 TAPER 2 7 8 EN 17 MAINTENANCE - CLEANING THE INLET VALVE i Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. YOU WILL NEED • 8 mm (5/16”) h...

1 2 3 4 5 18 EN MAINTENANCE - CLEANING THE OUTLET VALVE i Cleaning or servicing the outlet valve may be necessary if spray performance remains poor after following the steps in the Troubleshooting section. Call Technical Service (1-800-328- 8251) to order a new outlet valve assembly. YOU WILL NEED •...

EN 19 TROUBLESHOOTING PROBLEM CAUSE SOLUTION A. The sprayer does not turn on. 1. The sprayer is not plugged in. 2. The sprayer is turned OFF (0). 3. The sprayer shuts off while under pressure. 4. No power is coming from power outlet. 5. The extension cord is damaged or is not the proper gauge or len...

56 EN F ES PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS # 130 Description Description Descripción 1 0580538A Tank lid Couvercle de la réservoir Tapa de la tanque 2 0580072A Outlet valve assembly Ensemble de la soupape de sortie Conjunto de la válvula de salida 3 0580070 Set screw Vis de pression T...

1 4 2 3 5 57 PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS ES F EN Replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. Los repuestos están disponibles llamanado al servicio a clientes. 1-800-328-8251 # 130 Description...

58 EN F ES ACCESSORIES • ACCESSOIRES • ACCESORIOS PART NO. DESCRIPTION DESCRIPTION DESCRIPCIÓN SPRAY GUNS PISTOLETS DE PULVÉRISATION PISTOLAS DE PULVERIZACIÓN 0580600 Control Pro spray gun Pistolet de pulvérisation Control Pro Pistola de pulverización de Control Pro 0580601 Control Pro M spray gun P...

BESOIN D’AIDE? Appelez le service technique Wagner 1-800-328-8251 Enregistrement du produit en ligne sur le site : www.wagnerspraytech.com QUESTIONS? Call Wagner Technical Service at: 1-800-328-8251 Register your product online at: www.wagnerspraytech.com ¿NECESITA AYUDA? Llame Wagner Technical Serv...