Page 2 - IMportAnt SAFEtY InForMAtIon; EXplAnAtIon oF SYMBolS; GroUnDInG InStrUCtIonS
2 En IMportAnt SAFEtY InForMAtIon Read all safety information before operating the equipment. Save these instructions.To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and ...
Page 3 - SAFEtY hAzArDS; warning: EXPLOSiOn Or FirE
En 3 IMportAnt SAFEtY InForMAtIon SAFEtY hAzArDS warning: EXPLOSiOn Or FirE Solvent and paint fumes can explode or ignite. Severe injury and/or property damage can occur. PrEVEnTiOn: • Do not spray flammable or combustible materials near an open flame, pilot lights or sources of ignition such as hot...
Page 4 - warning: HaZarDOUS VaPOrS; tABlE oF ContEntS
4 En IMportAnt SAFEtY InForMAtIon • Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly. • Verify that all connections are secure before operating the unit. • Know how to stop the unit and bleed pressure quickly. Be thoroughly familiar with the controls....
Page 5 - GEnErAl InForMAtIon; MoDElS
En 5 GEnErAl InForMAtIon MoDElS This pump is available in stand models (150/170/190) and a cart model (170). Some of the graphics in this manual may not exactly match your sprayer and spray gun. All information and instructions given in this manual applies to all models except where noted.The type o...
Page 6 - pArtS AnD CoMponEntS; ItEM
pArtS AnD CoMponEntS 6 En SPRAY PRIM E SPRAY PRIME 4 2 5 8 2 7 3 9 15 54 6 3 7 8 9 1 4 10 12 11 14 SPRAY PRIME 13 # ItEM DESCrIptIon 1 Hose wrap The hose wrap allows for easy storage of the spray hose (cart models only). 2 Tool box The Tool Box provides a place for items such as extra spray tips or ...
Page 7 - tAp wIth A MAllEt; wAtEr; ChECk For SUCtIon; YoU wIll nEED; FIGUrE 2: tAp thE oUtlEt
SPRAY PRIM E 3 - 4X FIGUrE 1 FIGUrE 2 tAp wIth A MAllEt FIGUrE 3 SPRAY PRIM E 3 - 4X wAtEr (1-2 oz) En 7 ChECk For SUCtIon i Priming your pump is first step to getting ready to spray. Do a quick check to make sure there is suction as the valves can stick for various reasons. There are a few tricks P...
Page 8 - ASSEMBlY; toolS nEEDED
1 2 MEtAl plAStIC 3 4 5 ASSEMBlY 8 En Do not plug in the power cord until assembly is complete. toolS nEEDED • Two 6” adjustable wrenches 1. Attach the tool box doors to the top of the sprayer as shown. Snap one peg into one of the orifices, and then snap the other peg into the other orifice. The pe...
Page 10 - BEForE YoU BEGIn; SprAY GUn trIGGEr loCk
1 2 1 2 SPRAY PRIM E 3 4 5 10 En BEForE YoU BEGIn i This section contains instructions that will be repeated throughout this manual. Read and understand this section before using the equipment. SprAY GUn trIGGEr loCk Be careful when handling the spray gun so you do not accidently spray yourself. The...
Page 11 - loAD MAtErIAl
1 2 A B 3 SPRAY PRIM E 4 A B 5 En 11 loAD MAtErIAl i These steps will prime the system and get it ready to spray.www.wagnercontrolpro.com/howto YoU wIll nEED • The material you plan to spray • Extension cord • Waste bucket i recommendation: It is good practice to perform the steps on this page using...
Page 12 - or; SprAYInG
1 2 SPRAY PRIME 3 4 SPRAY PRIM E 5 or 6 or 7 SPRAY PRIME 12 En SprAYInG i Follow these steps to deliver spray material from the material container to the spray gun. YoU wIll nEED • Waste bucket • Scrap material / cardboard • Drop cloths to protect floors and furnishings from overspray 1. Make sure t...
Page 13 - prACtICE SprAYInG; Control pro tIp SElECtIon ChArt
En 13 prACtICE SprAYInG i Prior to spraying, it is important that you are using the spray tip / spray material combination that it suitable for your spraying job. Refer to the chart below for a list of recommendations regarding spray tip size, spray material and pressure settings. Control pro tIp SE...
Page 15 - SprAYInG troUBlEShootInG - ClEAr thE SprAY tIp
1 2 3 SPRAY PRIME 4 En 15 SprAYInG troUBlEShootInG - ClEAr thE SprAY tIp i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. Follow the steps below. YoU wIll nEED • Scrap material / cardboard Do not attempt to unclog or cl...
Page 16 - SprAYInG troUBlEShootInG - ClEAn thE InlEt FIltEr
1 2 3 16 En SprAYInG troUBlEShootInG - ClEAn thE InlEt FIltEr i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the inlet filter could be clogged. Follow the steps below. YoU wIll nEED • Warm, soapy water for latex material • Mineral spirits for oil ba...
Page 17 - AnD
1 SPRAY PRIM E 2 AnD 3 4 AnD 5 6 pAGE 12 En 17 Short-tErM StorAGE i This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow Cleanup instructions, pages 18-19. YoU wIll nEED • Water • Plastic bag • Damp rags • ...
Page 18 - ClEAnUp; ClEAnInG notES - rEAD BEForE ClEAnInG
1 SPRAY PRIM E 2 3 4 18 En ClEAnUp ClEAnInG notES - rEAD BEForE ClEAnInG • When using latex material, clean sprayer and components with warm, soapy water. For oil based material use mineral spirits. Never use mineral spirits with latex materials. • NEVER use gasoline to clean sprayer. • Dispose of u...
Page 20 - OIL; OIL; lonG tErM StorAGE
1 HOUSEHOLD OIL 2 3 a HOUSEHOLD OIL 4 5 lonG tErM StorAGE 20 En i Follow these steps to prepare your sprayer for long- term storage. YoU wIll nEED • Light household oil / All Guard • Rags • Two adjustable wrenches i The suction tube should still be removed from the end of the previous section and th...
Page 21 - ClEAnInG thE InlEt vAlvE
1 2 a b d e c 3 b c 4 En 21 ClEAnInG thE InlEt vAlvE i Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. YoU wIll nEED • Adjustable wrench or 10 mm alle...
Page 22 - ClEAnInG thE oUtlEt vAlvE
1 2 3 4 5 22 En ClEAnInG thE oUtlEt vAlvE i Cleaning or servicing the outlet valve may be necessary if spray performance remains poor after following the steps in the Troubleshooting section. Call Technical Service (1-800-328-8251) to order a new outlet valve assembly. YoU wIll nEED • Two 6” adjusta...
Page 23 - troUBlEShootInG
En 23 troUBlEShootInG proBlEM CAUSE SolUtIon A. The sprayer does not turn on. 1. The sprayer is not plugged in. 2. Pressure control knob is set to OFF. 3. The sprayer shuts off while under pressure. 4. No power is coming from power outlet. 5. The extension cord is damaged or is not the proper gauge ...
Page 24 - En F ES; Parts List • Liste de Pièces • Lista de Piezas; Main asseMbLy • enseMbLe PrinciPaL • Montaje PrinciPaL
68 En F ES Parts List • Liste de Pièces • Lista de Piezas # 150 170 190 Description Description Descripción 1 0580389 0580389 --------- Base assembly Ensemble de la base Conjunto de la base --------- --------- 0580175 Handle assembly Ensemble de la poignée Conjunto de la manilla 2 0580041Y 0580041Y ...
Page 25 - ES F En
69 Parts List • Liste de Pièces • Lista de Piezas ES F En # 170 Description Description Descripción 1 0580390 Handle assembly Ensemble de la poignée Conjunto de la manilla 2 0580041Y Door (single piece) Porte (pièce unique) Tapa (pieza única) 3* --------- Suction set assembly Ensemble d'aspiration C...
Page 27 - suction set asseMbLy • enseMbLe d’asPiration • conjunto de succiÓn
71 Parts List • Liste de Pièces • Lista de Piezas ES F En # 150 170 190 170 (cart) Description Description Descripción 1 ------- ------- ------- ------- Suction tube Tube d’aspiration Tubo de succión 2 0580487 0580487 0580487 0580208 Return tube Tuyau de retour Tubo de retorno 3 0512390 0512390 0512...
Page 28 - accessories • accessoires • accesorios
72 En F ES accessories • accessoires • accesorios pArt no. DESCrIptIon DESCrIptIon DESCrIpCIón SprAY GUnS pIStolEtS DE pUlvérISAtIon pIStolAS DE pUlvErIzACIón 0580600 Control Pro spray gun Pistolet de pulvérisation Control Pro Pistola de pulverización de Control Pro 0580601 Control Pro M spray gun P...
Page 29 - wArrAntY
73 ES F En AIrlESS pAInt SprAY EqUIpMEnt This product, manufactured by Wagner, is warranted to the original retail purchaser against defects in material and workmanship for two years from date of purchase.This warranty does not cover damage resulting from improper use, accidents, user’s negligence o...
Page 30 - GArAntíA
74 En F ES GArAntíA EqUIpo DE AtoMIzACIón DE pIntUrA SIn AIrE Este producto, fabricado por Wagner Spray Tech (Wagner), está garantizado ante el comprador original contra defectos de materiales y mano de obra durante dos años contado a partir de la fecha de compra.Esta garantía no cubre los daños que...
Page 32 - Control pro