US Stove Company 5510 - Manuals

USSC 5 iNSTALLATiON OPTiONS Read this entire manual before you install and use your Pellet stove. Failure to follow instructions may result in property damage, bodily injury, or even death! (See specific installation details for clearances and other installation requirements) A Freestanding Unit —su...

6 USSC Installation CLEArANCES Your King stove has been tested and listed for installation in residential, mobile home, and alcove applications in accordance with the clearances given in FIGURES 3-5 and TABLE 1. NOTE: Distance “C” on the left-hand side of your King stove may need to be greater than ...

USSC 7 Installation vENTiNg rEquirEMENTS Install vent at clearances specified by the vent manufacturer. Do not connect the pellet vent to a vent serving any other appliance or stove. Do not install a flue damper in the exhaust venting system of this unit. The following installation guidelines must b...

8 USSC Installation vENT TErMiNATiON CLEArANCES: A) Minimum 4-foot clearance below or beside any door or window that opens. B) Minimum 1-foot clearance above any door or window that opens. C) Minimum 3-foot clearance from any adjacent building. D) Minimum 7-foot clearance from any grade when adjacen...

USSC 9 Installation ThrOugh ThE wALL iNSTALLATiON (RECOMMENDED INSTALLATION) To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the exhaust adapter is at least 18-inches above ground level, a straight section of pellet vent pipe can be used through the wall....

10 USSC Installation OuTSidE Air SuPPLy (optional) Depending on your location and home construction, outside air may be necessary for optimal performance. Metal pipe (solid or flexible) must be used for the outside air installation. PVC pipe is NOT approved and should NEVER be used.A wind shield ove...

USSC 11 How your stove works Your King stove utilizes a inclined auger fuel feed system that is operated by a microprocessor controlled digital circuit board. The digital circuit board allows the inclined auger fuel feed system to run in a timer-based, non-continuous cycle; this cycling allows the a...

12 USSC Control Panel Overview ON/OFF Pressing the “ON” button on the control panel will begin the start-up sequence for the heater. Fuel will begin to feed through the auger feed system then ignite after approx. 5 minutes.Pressing the “OFF” button on the control panel will cause the heater to enter...

USSC 13 uNiT PrEPArATiON After carefully unpacking and reading the instructions for installing your stove, you will need to perform the following steps: Attach the included spring handle to the door handle by screwing it on in a respective location.Attach the electrical cord to the back of the stove...

14 USSC ShuT dOwN PrOCEdurE Press the “OFF” button on the control pad to put the stove in shut down mode. At this time, the red light above the pad will illuminate. Once this is done, the auger will stop feeding pellets, but the distribution blower and exhaust blower will continue to operate. When t...

USSC 15 Maintenance Operation dAiLy OPErATiON The hopper and stove top will be hot during operation; therefore, you should always use some type of hand protection when refueling your stove. Never place your hand near the auger while the stove is in operation. This unit should be filled when the hopp...

16 USSC iNTEriOr ChAMBErS Periodically remove and clean the burnpot and the area inside the burnpot housing. In particular it is advisable to clean out the holes in the burnpot to remove any build up that may prevent air from moving through the burn pot freely. Remove the two(2) plates on each side ...

USSC 17 Trouble Shooting Disconnect the power cord before performing any maintenance! NOTE: Turning the ON/OFF Switch to ”OFF” does not disconnect all power to the electrical components of the stove. Never try to repair or replace any part of the stove unless instructions for doing so are given in t...

18 USSC Error Code Err1 Err2 Err3 Err4 Err5Err6Err7 Err8 Error DescrptionThe high limit temperature sensor has tripped. Stove ran out of fuel during normal operation. The stove was unable to reach the Room Fan On temperature within the startup time.The power failed while the stove was hot, and when ...

USSC 19 Parts Diagram 11 3 2 1 5 6 4 7 9 8 10 12 Viewing Door Detail

20 USSC PARTS LIST Item Part No. Title Qty. 1 69524 Door Assembly 1 2 891372 Hinge Pad, Threaded 2 N/S 83045A Washer, 3/8” 2 N/S 83274 3/8-16 Lock Nut 2 3 25080 Door Latch 1 4 891395 Ash Pan Bed 1 N/S 83508 5/16-18 Bolt 1 N/S 83338 5/16-18 Nut 1 5 891390 Ash Pan Weld. 1 6 891396 Die Cast Knob (Nicke...

24 USSC This manual will help you obTain efficienT, dependable ser- vice from your KinG or ashley, and enable you To order repair parTs correcTly. Keep This manual in a safe place for fuTure reference. when wriTinG, always Give The full model number which is on The nameplaTe aTTached To The heaTer. ...