Tripp Lite B126-4X4 - Manuals

Page 2 - routed to multiple outputs

2 Package Contents Product Features • B126-2X2 or B126-4X4 Local Transmitter Unit• External Power Supply (Input: 100-240V, 50/60Hz, 0.5A Output B126-2X2: 5V, 2A; Output B126-4X4: 5V, 3A) • 3.5 mm to DB9 Adapter Cable• Mounting Hardware• Remote Control• Owner’s Manual • Share multiple HDMI sources be...

Page 3 - Product Features; • Add up to three repeaters on each channel of the matrix switch, for a; Optional Accessories:

3 Product Features • Add up to three repeaters on each channel of the matrix switch, for a total of 4 displays per channel (An active remote receiver should be the last unit in a channel) • A 1080p @ 60Hz signal can be extended up to 125 ft. for each repeater added into a channel (or up to 175 ft. f...

Page 4 - Mounting; different mounting methods.; Wallmount 1

4 Mounting The B126-2X2 and B126-4X4 come with mounting hardware that allows them to be mounted in a variety of ways. The following images show the different ways the included mounting brackets can be attached for different mounting methods. Note: The images below show a B126-1A1 HDMI over Cat5 Rece...

Page 5 - Standard Installation; to a

5 Standard Installation Note: 1. Test to make sure that the entire installation works properly before pulling cables through ceilings/walls. 2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The diagram below shows a B126...

Page 7 - Remote Repeater Installation; Make sure all devices being connected are turned off.

7 Remote Repeater Installation Note: 1. Test to make sure that the entire installation works properly before pulling cables through ceilings/walls. 2. 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, is required to achieve maximum distance and resolution. 3. The diagram below shows...

Page 8 - ports that have devices connected

8 Remote Repeater Installation 5 Connect the external power supply to the switch and plug it into a Tripp Lite Surge Suppressor, PDU, or UPS. When receiving power, the following LEDs will illuminate: The Green Power LED, the Orange Source LEDs (for the Source ports that have devices connected to the...

Page 9 - ports on the switch.; remote control of the desired; section in this manual for details on

9 Remote Repeater Installation 12 Using Cat5e/6 cable, connect the RJ45 output port on the last repeater to the RJ45 input port on a B126-1A0 or B126-1A0-WP-1 receiver. 13 Connect a monitor to the HDMI output port on the receiver using a Tripp Lite P568-Series High-Speed HDMI cable. 14 Connect the e...

Page 12 - of sw1 A would display source A on output 1.

12 RS232 Serial Control 5 Once these settings are updated, the Terminal Emulation Software will recognize the switch, allowing you to enter commands to control it with. The following table lists the available commands. Command Action sw[x] [n] Switches the source being displayed on the selected outp...

Page 13 - Troubleshooting

13 Troubleshooting If you are unable to get an acceptable image after following the installation instructions, try the troubleshooting tips below. 1 Are the external power supplies that came with the product connected and plugged into a working power source? For the product to function properly, it ...

Page 14 - causing poor performance. If you have a patch panel or other device

14 Troubleshooting 6 Test your cables to ensure they are working properly. For example, connect your HDMI cables between a source and monitor that you know works to see if the cable is functioning. For Cat5e/6 cable, connect it between a computer and a network to verify that it establishes a network...

Page 15 - Warranty & Warranty Registration; -Year Limited Warranty

15 Warranty & Warranty Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at i...

Page 16 - WARRANTY REGISTRATION; WARNING

16 1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support 13-11-140 93-32BB_revC WARRANTY REGISTRATION Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite pr...