Texas Instruments DW30 - Manuals

Section 1: Introduction 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 1-3 The light generated by the lamp(s) is then sequentially filtered into the RGB color primaries by the spinning color wheel(s) and presented to the single chip DMD, located in the light engine, in se...

Section 1: Introduction 1-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Whether the projector is under warranty or the warranty has expired, Christie’s highly trained and extensive factory and dealer service network is always available to quickly diagnose and correct p...

Section 2 Installation & Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30Matrix 3000 User’s Manual 2-1 The instructions provided here are for those that are familiar with the projector and wish to quickly set it up and use it temporarily. Refer to the remaining subsections of this manual f...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-3 Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently you should take the following into account...

Section 2: Installation and Setup 2-6 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Figure 2.1. Estimating Throw Distance Vertical and horizontal position The correct vertical and horizontal position of the projector in relation to the screen depends on the lens type and...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-7 Table 2. 2 Lens Offsets for DW30 (720P) % Pixels % Pixels % Pixels % Pixels 0.8:1 fixed 81% +/-292 90% +/-652 31% +/-200 66% +/-840 1.2:1 fixed 231% +/-832 110% +/-1192 104% +/-664 102% +...

Section 2: Installation and Setup 2-8 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Figure 2.3. Lens Vertical Offsets The horizontal position of the image can be offset – that is moved to the left or right of lens center, by adjusting the fully motorized lens mount throu...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-9 Figure 2.4. Examples of Horizontal Offset

Section 2: Installation and Setup 2-10 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Figure 2.5. Lens Horizontal Offsets Lifting and transporting the projector – The projector is light enough to lift and transport a short distance. Use the indentations on the bottom of t...

Section 2: Installation and Setup 2-12 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Sources connect to the Input Panel located at the back of the projector. See Figure 2.10. The upper right corner ( INPUT 1 ) typically accepts an RGB signal from an external analog RGB s...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-13 Figure 2.11. Connecting RGB and Sync NOTES: 1) If for some reason the projector fails to recognize a signal as an RGB signal, specify the Color Space option within the Image Settings men...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-15 As an alternative to the projector’s keypad or remote, you may wish to communicate with the projector using a PC or other controller. Such a device sends commands and receives feedback v...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-17 Regardless of how it is assigned, once a projector has a valid and unique address it will respond to commands sent to this address. To determine the projector’s current IP address, consu...

Section 2: Installation and Setup 2-18 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Note that communication parameters such as baud rate must be set to match the particular controlling device before connecting as a network—refer to the documentation that came with your ...

Section 2: Installation and Setup 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 2-19 NOTES: Only the port and IP address of the projector can be changed. The subnet mask is fixed (255.255.255.0). CHANGING THE PORT#: On some Ethernet networks, firewall restrictions may re...

Section 2: Installation and Setup 2-20 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Plug the line cord to the AC receptacle located on the right hand side of the projector and the three-pronged end into a grounded AC outlet (Figure 2.22). The input voltage to the projec...

Section 3 Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW3K/Matrix 3000 User’s Manual 3-1 This section explains how to effectively operate the projector once it has been installed. It is recommended that you read this section and familiarize yourself with the components and the available me...

Section 3: Operation 3-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) (3) The AC receptacle is located on the right side of the projector (opposite side of lamp doors). Use this outlet to plug in an appropriately rated line cord. See 2.6 Power Connection for details. Th...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-3 (6) & (11) The two IR sensors located on the projector receive transmissions from the IR remote from up to 100 feet away. It is important to keep the transmission path to these sensors unobstructe...

Section 3: Operation 3-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) The IR remote controls the projector by way of wireless communications from a battery-powered infrared (IR) transmitter. Use the IR remote the same way you would use a remote control supplied with a T...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-5 You can convert the IR remote into a wired IR remote using the cable provided with the projector. Connect one end into the remote and the other to the mini stereo connector on the input panel labeled ...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-7 Contrast Press Contrast to change the amount of white in your images. Use keys until you reach the desired level of contrast—for best results, start low and increase so that whites remain bright but a...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-9 NOTES: 1) The "Broadcast Keys" option in the Communications menu must be selected for only one (any) projector in a serial network. The keypad in use must be OFF (disabled) for the remaining p...

Section 3: Operation 3-10 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Laser Press to activate the laser pointer on the remote. This feature is useful when making presentations - just point the remote at the screen to highlight an area of your presentation. Keep the key...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-11 Figure 3.5. Context-sensitive Help From presentation level, press Help to access general Help Topics . Scroll as necessary within a topic. Press Help or Exit to return to your presentation. Figure 3....

Section 3: Operation 3-12 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Once selected, change the setting as desired (see below) and press to save and return to the current function menu. Slidebars in menus – The current value for a given parameter, such as size or verti...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-13 If you prefer to quickly scroll through a list without first pulling it down, highlight the option and use . Press when the desired choice appears. NOTES: 1) Press or to jump between pages in an extr...

Section 3: Operation 3-14 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) NOTES: 1) Once you enter the first digit, this digit replaces all old digits. 2) If you press any non-numbered key, the number entered up to that point is accepted and updated as the new value. 3) Pr...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-15 Shown at right is a sample channel list as would be available from C han nel . This is typically called the channel list . NOTE: The C han nel key may display a channel list or not, depending on what...

Section 3: Operation 3-16 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) All available channels are listed in the Channel Setup menu, which describes how each channel can be accessed and which serves as the gateway for editing, copying and deleting channels. From the pres...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-17 FUNCTIONS WITHIN THE CHANNEL SETUP MENU — To copy, delete or edit a channel, highlight the desired channel in the Channel Setup menu and do one of two things: • Press Func if you want to copy the sel...

Section 3: Operation 3-18 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) TO DELETE MULTIPLE CHANNELS , highlight any channel in the Channel Setup menu and press Func to go to the Channel Copy/Delete submenu. Select “Delete Unlocked Only” and press to delete all unlocked c...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-19 • AUTO SOURCE: If checked, (default), the projector can automatically locate this channel when an incoming input signal matches. If not checked, the projector can locate the selected channel only whe...

Section 3: Operation 3-20 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) In the Size and Position menu, you can increase or decrease the size of your image, change its proportion (aspect ratio), move the image to a specific area of the screen, and refine other related par...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-21 • Select “NO RESIZING” to display the image in its native resolution, which may or may not match the projector’s resolution. For example, for a source with a native resolution of 800 x 600, “No Resiz...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-23 H-Position This option moves the image right or left within the area of available pixels. NOTE: The value shown represents where the approximate center of the image lies in relation to the total numb...

Section 3: Operation 3-24 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) PLUG & DISPLAY (EDID): By default, a Plug & Play (EDID) source outputs a signal according to the EDID information provided by the projector. To override this information and display in a diff...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-25 Brightness ( SHORT CUT: Press Bright an d adjust the slidebar.) “Brightness” increases or decreases the amount of black in the image (0-100). For best results, keep close to 50. Start with a high val...

Section 3: Operation 3-26 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Noise Reduction “Noise Reduction” is similar to the “Filter” control, but operates in the post-sampling digital domain with a more subtle effect. Higher settings are most useful for clearing up noisy...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-27 VIDEO STANDARD: For all but the more unusual video standards available in the world, the projector automatically detects the incoming horizontal and vertical frequencies and sets the projector’s proc...

Section 3: Operation 3-28 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) DECODER LUMA DELAY – This control affects any incoming composite or S-video signal, delaying the luma signal (intensity) in relation to the chroma (color). In the image, increasing the luma delay wil...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-29 then delete the checkmark and exit. The Auto Input Level is automatically turned off upon exiting the Input Levels menu. BLACKLEVELS AND DRIVES – To check your image levels and adjust these controls:...

Section 3: Operation 3-30 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) black and white are known to be at opposite edges of the image, you can watch these isolated areas while adjusting individual blacklevels and input drives until both black and white edges are just vi...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-31 Advanced Image Settings — SUBMENU Use the Advanced Image Settings submenu to make the adjustments necessary for lesser-used but more specialized applications on your projector. GAMMA TABLE: This cont...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-33 Simulation 3D — SUBMENU OF ADVANCED IMAGE SETTINGS This submenu allows you to adjust the timing between the input signal and its appearance on screen. This is most useful in applications where you wa...

Section 3: Operation 3-34 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) DETAIL THRESHOLD — Use “Detail Threshold” to define at what frequency level the “Detail” control will begin to magnify high frequencies, which adds details back into the image. Raise the threshold to...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-35 Menu Preferences — SUBMENU Adjust the appearance, content and/or location of on-screen menus and messages. LARGE MENU FONT — Enter a checkmark to enlarge menus and their text. You may have to adjust ...

Section 3: Operation 3-36 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) • Startup And No Signal – A splash screen appears at startup only if there is no source signal. To replace the default “Christie logo” splash screen (or other) with one of your own, use KoRE Libraria...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-37 Figure 3.17. Using the “Network Routing” Option RS232 AND RS422 JOINED: Messages originating from an RS232 or RS422 controller will be relayed to all RS232or RS422 ports. Any Ethernet communication, ...

Section 3: Operation 3-38 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) by a DHCP server or other user. It takes approximately 10 seconds for the projector to respond at its new address. PORT: On some Ethernet networks, firewall restrictions may require that the port num...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-39 * Functions are only active when the Slider Lock is set to Unlocked NOTE: It is important to ensure the channels DO NOT overlap another device. Example: Good Bad Proj1_Base = 0 Proj1_Base = 5 Proj2_B...

Section 3: Operation 3-40 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) To disable both IR sensors, you cannot use the IR remote keypad to select the second OFF setting. This safeguard prevents accidentally disabling an IR keypad while you are using it. Instead, use eith...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-41 memory, typically creating one or more “squeezed” or stretched areas in the display. If no custom warps have been created, the User options will have no effect. 2D KEYSTONE: Move one or more corner p...

Section 3: Operation 3-42 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Use to correct a keystoned image shape in which both sides of the image are inclined toward the top or bottom edge. Keystone is typically caused by tilting the projector in relation to the screen so ...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-45 Test Pattern Choose the desired internal test pattern to display, or select OFF to turn off a test pattern. Alternatively, use the Test key for cycling through test patterns. NOTE: There is a center ...

Section 3: Operation 3-46 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Two sets of values are automatically saved with these controls—one value for Input #1, and one for Input #2 (analog). The current set of values depends on which source is in use. This enables a sourc...

Section 3: Operation 3-48 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) PIP (Picture-in-Picture) and Seamless Switching are independent but related projector features that both utilize two image processing paths within the projector. In the case of Picture-in-Picture, th...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-49 Swap Main and PIP Image Toggle the current picture-in-picture relationship so that the primary (main) image becomes secondary (PIP), and the secondary image becomes primary. Swapping is available onl...

Section 3: Operation 3-50 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) PIP Border Width Set the desired line thickness for your PIP window border. PIP Border Color Select the desired color for the PIP window border. NOTES: 1) Numbers 7 and 8 on the Picture-in-Picture an...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-51 Numbers Select Main Image Use Numbers Select Main Image to use the numeric keys #1-8 as input keys. This remapping of the keypad (see right) can be particularly useful with PIP displays, providing a ...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-53 Figure 3.24. The Lamp Menu LAMP MESSAGE - Enter a checkmark to enable a warning message that will appear upon power-up when the lamp has reached the specified lamp limit and should be replaced. Delet...

Section 3: Operation 3-54 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) NOTES: 1) The projector will automatically shutdown if it detects both lamps have “failed” (this includes lamps not installed). 2) The lamp operation mode will not automatically switch to a previous ...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-55 The read-only Status menu lists a variety of details about the standard and optional components currently detected in the projector. Refer to the Status menu for versions of hardware and software ins...

Section 3: Operation 3-56 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Color Adjustment Procedure Once the Color Primary Settings are calibrated for the site (see above), use the Color Adjustments by X,Y or Color Saturation menu to further refine each projector’s fundam...

Section 3: Operation 3-58 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) 7. All screens should now be color-matched and the will remain matched upon exit from the menus. Apply this new “User” gamut to a source at any time by selecting it in the “Select Color Adjustment” l...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-59 ‰ ADJUST COLORS FIRST— Always adjust the primary colors as described in the “ Matching Colors in Multiple Screens ” procedure (above) before attempting to work with Brightness Uniformity. This ensure...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-61 blue, too red or too green, go to the Left Uniformity menu and adjust the colors (i.e., change their light output) until all portions of the left side closely match the center color temperature. Adju...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-63 Main Functions Use standard edge blending controls to set the precise width , shape and midpoint you need to blend overlapping edges together smoothly. ‰ Blend Width determines how much area is used ...

Section 3: Operation 3-64 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) ‰ Show Blending Overlap turns your defined blend width area to solid gray so that two adjacent images can be seamlessly aligned simply by overlapping their gray bars, if needed. Toggle the Show Blend...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-65 3. SET STARTING POINTS FOR ADJUSTMENT : ‰ Set all blend widths to 0. ‰ Go to “More” and set everything in the Edge Blending (2) menu to 50. Figure 3.35. Set Starting Points for Each Projector 4. SET ...

Section 3: Operation 3-66 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) VIA ASCII MESSAGING — Connect a serial link between your controller and the RS232 or RS422 port (recommended), or open an Ethernet socket (i.e., Telnet) between your controller and the valid projecto...

Section 3: Operation 3-68 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) should be reported to the manufacturer. You can press Exit Exit to remove the message, but for best results you should reset the projector—power the projector down and up again with the (power) key. ...

Section 3: Operation 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 3-69 Code Description GENERAL 12 Software bug. Contact dealer/factory. 13 Flash memory corrupted. Download new software. 14 Engineering only programming is complete. Call Christie, replace TIPM. 15 Attemp...

Section 4 Maintenance 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW3K/Matrix 3000 User’s Manual 4-1 The projector is an international regulatory agency approved product designed for safe and reliable operation. It is important to acknowledge the following precautions while operating the projector t...

Section 4: Maintenance 4-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) WARNING Always power down and unplug the projector before cleaning or servicing. Table 4.1. Maintenance Guide Part Description Frequency How to clean Lens As required Clean the lens only when absolu...

Section 4: Maintenance 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 4-5 The optional IR remote uses two AA size, 1.5V alkaline batteries. To replace the batteries simply turn the remote over and push out the cover using the finger groove, as shown in (1) Figure 4.1. Rem...

Section 4: Maintenance 4-8 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) Use the following instructions when replacing a projection lens: NOTE FOR FIRST TIME USE: The projection lens is shipped separately from the projector. Before you install a lens it is important to r...

Section 5 Troubleshooting 013-100149-02 Rev. 1 (01/07) Christie DS+60/Dw3K/Marix 3000 User’s Manual 5-1 If the projector does not appear to be operating properly, note the symptoms present and use the following guide to assist you. If you cannot resolve the problems yourself, contact your dealer for...

Section 6 Specifications 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 6-1 NOTES: 1) Due to continuing research, specifications are subject to change without notice. 2) Specifications apply to all models unless otherwise noted. Resolution SXGA+ (1400 x 1050) for DS+60 an...

Section 6: Specifications 6-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) * for DS+60 and Matrix 3000 , 0% offset is equal to half the image above and below lens center (525 pixels) OR half the image to the left or right of lens center (700 pixels) – see table below. T...

Section 6: Specifications 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual 6-3 Composite Video and S-Video Signal Formats Composite-video (CVBS), S-video Y/C) Video Standards NTSC, NTSC 4.43, PAL, PAL M, PAL N, PAL60, SECAM Input Levels Composite-video: 1.0Vp-p ± 3db (inclu...

Section 6: Specifications 6-4 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) General Voltage Range 100 – 240 VAC nominal Line Frequency 50 Hz – 60 Hz nominal Max. Inrush Current 68 A Current Rating Both lamps on - 8.4A @ 100V (typical), 3.5A @ 240V (typical) One lamp on -...

Appendix A Glossary 013-100149-02 Rev. 1 (01/07) Christie DS+60/DW30/Matrix 3000 User’s Manual A-1 This appendix defines the specific terms used in this manual as they apply to this projector. Also included are other general terms commonly used in the projection industry. The time, inside one horizo...

Appendix A: Glossary A-2 Christie DS+60/DW30/Matrix 3000 User’s Manual 013-100149-02 Rev. 1 (01/07) A number that uniquely identifies a specific channel retained in projector memory. The projector can retain up to 50 channels. A menu item that indicates whether an option is currently in effect (chec...

Appendix B IR Remote Key Reference Christie DS+60/DW30/Matrix 3000 User’s Manual B-1 NOTE: The IR remote is a standard component provided with the projector. Use the extension cable also provided to convert the IR remote to a wired remote, if desired. Refer to Section 3 for a specific description of...

Appendix C Serial Communication Cables Christie DS+60/DW30/Matrix 3000 User’s Manual C-1 A serial link of RS232 or RS422 enables ASCII communication with the projector so that it can be controlled remotely from a PC or other controller. From a PC, connect a standard 9-wire RS232 serial cable to the ...

Appendix D Throw Distance Christie DS+60/DW30/Matrix 3000 User’s Manual D-1 Calculating Throw Distance It is important throw distance be precisely calculated for your installation using the appropriate formula from the chart below. To calculate throw distance you must know the screen size and the le...

Appendix E System Integration Christie DS+60/DW30/Matrix 3000 User’s Manual E-1 The GPIO connector located on the input panel provides a flexible method of interfacing a wide range of external I/O devices to the projector. There are 7 GIO pins available on the 9pin D-Sub GPIO connector, which are co...

Appendix E: System Integration E-2 Christie DS+60/DW30/Matrix 3000 User’s Manual Query Command (GIO?) Request the state and configuration of all pins (GIO! “HHLLHLH” “OOIOOOI”) Reply of pin state and configuration (GIO? C2) Request configuration for pin #2 (GIO! C2 O) Reply with pin #2 configuration...

Appendix F Optional Input Modules Christie DS+60/DW30/Matrix 3000 User’s Manual F-1 There are many optional input modules and accessories currently available for this projector . Contact your dealer for a complete and up-to-date listing. NOTE: Always unplug the projector or switcher before installin...

Appendix G 300W P-VIP ® Product Safety Data Sheet Christie DS+60/DW30/Matrix 3000 User’s Manual G-1

Appendix G: 300W P-VIP Product Safety Data Sheets G-2 Christie DS+60/DW30/Matrix 3000 User’s Manual

Index Christie DS+60/DW30/Matrix 3000 User’s Manual A Adjusting Input Levels, 3-29 Advanced Image Settings, Submenu, 3-31 Anamorphic, 3-22 Arrow Key, 3-9 Arrow Keys, 3-9 Auto Input Level, 3-28 Auto Key, 3-5 Auto Setup, 3-5, 3-19 Automatic Gain Control (AGC), 3-26 AutoSource Checkbox, 3-19 B Bad Sync...