Sunrise Medical P-220 - Manuals

Page 2 - I . I n t r o d u c t i o n; SUNRISE LISTENS

930475 Rev. A I . I n t r o d u c t i o n 3 SUNRISE LISTENS Thank you for choosing a Quickie wheelchair. We want to hear your questions or comments about this manual, the safety and reliability of your chair, and the ser-vice you receive from your Sunrise supplier. Please feel free to write or call ...

Page 3 - MANUAL WHEELCHAIR CONVERSION KIT; I I . T a b l e o f C o n t e n t s; II. TABLE OF CONTENTS

930475 Rev. A I I . T a b l e o f C o n t e n t s 5 IX. SET UP, ADJUSTMENT & USE ................................................................................ 27 Notes ................................................................................................................ 27Tools You ...

Page 6 - F. REPORT ALL SUSPECTED EMI INCIDENTS; V . E M I ( E l e c t r o m a g n e t i c I n t e r f e r e n c e ); NOTE–

930475 Rev. A V . E M I ( E l e c t r o m a g n e t i c I n t e r f e r e n c e ) 11 4. The following specialty input devices have an unknown effect on the immunity level because they have not been tested with the P-220 and QTRONIX control system: •Breath Control • Proportional Head Control •Tri-Swi...

Page 8 - L. MOTOR VEHICLE SAFETY; V I . G e n e r a l W a r n i n g s; H. WHEN SEATED IN A PARKED WHEELCHAIR

930475 Rev. A V I . G e n e r a l W a r n i n g s 15 3. When not in use, keep your chair in a clean, dry place. Extra caution should be used when employing the disc switch or the proximi-ty head array as control devices. These two devices are susceptible to mal-function when wet. J. TERRAIN 1. This ...

Page 10 - Figure 1

930475 Rev. A V I . G e n e r a l W a r n i n g s 19 T. TO REDUCE THE RISK OF A FALL, TIP-OVER OR LOSS OF CONTROL: 1. Never use your chair on a slope unless you are sure you can do so without losing traction. 2. Always go as straight up and as straight down as you can. •Do not “cut the corner” on a ...

Page 11 - Never

930475 Rev. A V I . G e n e r a l W a r n i n g s 21 W. CURBS & SINGLE STEPS 1. Your chair is not designed to drive up or down a curb or step more than two (2) inches (5 cm) high. Doing so may: •Result in a fall or tip-over. •Damage the frame, wheels, axles or other chair parts, or loosen fasten...

Page 14 - V I I I . T i p s f o r A t t e n d a n t s

930475 Rev. A I X . S e t - U p , A d j u s t m e n t & U s e 27 NOTES 1. Work Surface For Set-Up: Use a flat surface, such as a table, to assemble, adjust and check your chair. This makes the steps easier and helps ensure a correct set-up. 2. Fasteners: • Many of the screws and bolts on this ch...

Page 17 - Height-Adjustable Armrest Key; Tension Adjustment Set Screw

930475 Rev. A I X . S e t - U p , A d j u s t m e n t & U s e 33 2. Height Adjustment a. Rotate release lever to stop.b. Slide armrest pad up or down to desired height. c. Return lever to locked position.d. Push arm pad until upper armpost locks firmly into place. 3. Removing Armrest a. Rotate r...

Page 20 - off; X . O p e r a t i n g G u i d e; A. PERFORMANCE CONTROL SETTINGS

930475 Rev. A X . O p e r a t i n g G u i d e 39 2. To Program Your Chair: a. Turn off power to the chair. b. Insert Qtronix Programmer plug (A) into the Programmer/Charger socket (B) on the front ofthe joystick. c. Turn on power to the chair; program as needed. d. Remove plug and cycle ON/OFF switc...

Page 21 - Speed Control or Drive Mode Selection Buttons; Integral Joystick

930475 Rev. A X . O p e r a t i n g G u i d e 41 • When you release the joystick it will return to neutral; the chair will slow to a stop and themotor locks will reengage. • We recommend that you switch the chair off if you stop for any length of time. This will con-serve battery power. NOTE– Once t...

Page 22 - actuator modes. The selected mode indicator will flash.

930475 Rev. A X . O p e r a t i n g G u i d e 43 G. MOTOR LOCKS Disconnect the motor locks when you need to manuallypush the chair. (For example, in an emergency, or if batteries fail). 1. Do not disengage motor locks unless power to the chair is off. 2. Be aware that the chair will not have brakes ...

Page 24 - Place the battery compartment lid on power

930475 Rev. A X I . B a t t e r i e s 47 X I . B a t t e r i e s 930475 Rev. A 46 3. Tighten all terminal fasteners using two 1/2" box end wrenches to 60 in-lbs (6.8 N.m). 4. Place the battery compartment lid on power base and secure using the two (2) quarter turnfasteners (push down on fastener...

Page 25 - injury from chair failure, damage or premature wear.

930475 Rev. A X I I . M a i n t e n a n c e 49 X I . B a t t e r i e s 930475 Rev. A 48 A. NOTES 1. Proper maintenance will improve performance and extend the useful life of your chair. 2. Clean your chair regularly. This will help you find loose or worn parts and will make your chair easier to use....

Page 27 - Release all air from tire.; VSI WIRING DIGRAM DETAIL

930475 Rev. A X I I I . W i r i n g D i a g r a m 53 X I I . M a i n t e n a n c e 930475 Rev. A 52 2. 12" (310 mm) Drive Wheels: a. Elevate and securely support chair so that wheel is off the ground. Release all air from tire. b. Remove four (4) lug nuts (A) from rim using a socket wrench. c. M...

Page 28 - ADDITIONAL WARRANTY; international warranties apply.; NOTICE TO CONSUMER

930475 Rev. A X I V . S u n r i s e L i m i t e d W a r r a n t y 55 X I I I . W i r i n g D i a g r a m 930475 Rev. A 54 1. FOR LIFE We warrant the main frame of this wheelchair against defects in materials and work-manship for the lifetime use of the first consumer purchaser. 2. ADDITIONAL WARRANT...

Page 29 - Sunrise Medical