Spirit EL1 - Manuals

Spirit EL1 – Manual in PDF format online.

Manuals:

Manual

Manual Spirit EL1

Summary

Page 2 - Table of Contents

EL1 Elliptical 1 Product Registration ..2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..4 Assembly Instructions .5 Operation of Your New Elliptical ...11 Manufacturer s Limited Warranty ..15 Table of Contents

Page 3 - RECORD YOUR SERIAL NUMBER; REGISTER YOUR PURCHASE; CONGRATULATIONS ON YOUR; Product Registration

EL1 Elliptical 2 Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc.Your new elliptical was manufactured by one of the leading fitness manufacturers in theworld and is backed by one of the most comprehensive warranties available. Throughyour dealer, Spirit ...

Page 4 - - Read all instructions before using this appliance.; elliptical; Important Safety Instructions

EL1 Elliptical 3 WARNING - Read all instructions before using this appliance. Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet and elliptical may result. Keep children away from the elliptical . There are obvious pinch points and other caution areas that can ca...

Page 5 - Important Electrical Information

EL1 Elliptical 4 WARNING! NEVER remove any cover without first disconnecting AC power supply. If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you sus pect the voltage is low, contact your...

Page 6 - Assembly Pack Check List

EL1 Elliptical 5 Step 1 Assembly Pack Check List 5/16" x 15m/mHex Head Bolt (6pcs ) 5/16"x 23 x1.5TFlat Washer (4pcs) 5/16"x 23 x2TCurved Washer (2pcs) M5 x 10m/mPhillips Head Screw (4pcs) Step 2 5/16 x 32m/mHex Head Bolt (2 pcs) 5/16" x 20 x 1.5TFlat Washer (4 pcs) 5/16" x 7TNyl...

Page 7 - Tools

EL1 Elliptical 6 3.5x12m/mSelf Tapping Screw (8pcs) M5 x 15m/mPhillips Head Screw (8pcs) Tools Combination M5 Allen Wrench& Phillips Head Screw Driver (1 pc) 12m/m Wrench ( 1pc) 13/14m/m Wrench ( 2pcs) Step 4

Page 8 - UNPACKING THE UNIT; STEP 1: CONSOLE MAST ASSEMBLY; STEP 2: HANDLE BAR ASSEMBLY; Assembly Instructions

EL1 Elliptical 7 UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missi...

Page 9 - STEP 3: CONNECTING ARM ASSEMBLY

EL1 Elliptical 8 STEP 3: CONNECTING ARM ASSEMBLY 1. Align the hole in the end of the Connecting arms (L&R)(pivoting rod end) with the hole in the bracket of the Lower Handle Bars (L&R). The rod end should be on the inside ofthe Lower Handle Bars (L&R) bracket. Take 2pcs of 5/16" x 1-...

Page 10 - Assembly drawing

Page 14 - Getting familiar with the control panel; Operation of Your Elliptical

EL1 Elliptical 13 The elliptical is equipped with two transport wheels that are engaged when the rear of the Elliptical is lifted. Getting familiar with the control panel Power up The Elliptical is supplied with an external power supply. When power is connected to the Elliptical,the console will aut...

Page 15 - Console Operation; Quick Start mode

EL1 Elliptical 14 Console Operation Quick Start mode This is the quickest way to start a workout. After the console powers up you just press the Startkey to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zeroand the workload may be adjusted manually by pre...

Page 16 - Entering a program/Changing Settings

EL1 Elliptical 15 Entering a program/Changing Settings Use the Up or Down key to scroll through the program selections. The profile for each program willbe displayed in the dot matrix window. Press the enter key to select a program and begincustomizing the s ettings. If you want to workout without e...

Page 17 - The Programs

EL1 Elliptical 16 The Programs HILL The Hill program simulates going up and down a hill. The resistance in the pedals will steadily increase and then decrease during the program. To start the Hill program follow the instructionsbelow or just select the Hill program then the Enter button and follow t...

Page 18 - Cardio

EL1 Elliptical 17 7. If you want to increas e or decrease the workload at any time during the program press the Up or Down key. This will only affec t the workload for the present position in the profile. When theprofile changes to the next column it will return to the preset work level. 8. During t...

Page 19 - Interval

EL1 Elliptical 18 6. Now you are finished editing the settings and can begin your workout by pressing the Start key. You can also go back and modify your settings by pressing the Stop key to go back onelevel, or screen. 7. If you want to increas e or decrease the workload at any time during the prog...

Page 20 - Heart Rate Control Program operation

EL1 Elliptical 19 then press enter to continue to the next segment. 6. The next segment will show the same level as the previously adjusted segment. Repeat the same process as the last segment then press enter. Continue this process until all twentysegments have been set. 7. The message window will ...

Page 21 - Maintenance Menu in console software:

EL1 Elliptical 20 Maintenance: 1. Wipe down all areas in the sweat path with a damp cloth after each workout. 2. If a squeak, thump, clicking or rough feeling develops the main cause is most likely one of two reasons: i. The hardware was not sufficiently tightened during assembly. All bolts that wer...

Page 22 - ELLIPTICAL WARRANTY; Manufacturer’s Limited Warranty

EL1 Elliptical 21 Effective September 15, 2007 ELLIPTICAL WARRANTY Spirit Manufacturing Inc. warrants all its elliptical parts for a period of time listed below from the date of retail sale as determined by sale receipt, or in the absence of a receipt eighteen (18) months from the orig inal factory ...