Smeg SRV876AV9 - Manuals

Smeg SRV876AV9 Hob – User Manual in PDF format online.

Manuals:

User Manual

User Manual Smeg SRV876AV9

Summary

Page 2 - Introduction; INSTRUCTIONS FOR SAFE AND PROPER USE

Introduction 22 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE...

Page 3 - DO NOT PUT; The manufacturer declines all responsibility

Introduction 23 THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDE...

Page 4 - Instructions for the installer; POSITIONING OF THE HOB; must be carried out by a competent tradesman.; Attachment to support structure; on the inner side

Instructions for the installer 24 2 POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as the...

Page 5 - In case of installation on a hollow compartment with doors, a

Instructions for the installer 25 In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. Keep a minimum distance of 10 mm between the bottom of the unit and the panel surface. The panel has to be easily removable to allow access in the event of...

Page 6 - ELECTRICAL CONNECTION; not be less than 1.0 mm

Instructions for the installer 26 3 ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same t...

Page 7 - GAS CONNECTION; rigid copper; The flexible pipe has to be installed so that pipe length does not

Instructions for the installer 27 4 GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force. To facilitate connection, fitting A on the rear of the appliance may be adjusted late...

Page 8 - Connection to LPG; Use a pressure regulator and make the connection to the tank; Ventilation of rooms; Discharge of combustion products must be guaranteed by means of

Instructions for the installer 28 4.1 Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph “5.2 Regulation for LPG”. 4.2 Ventil...

Page 9 - ADAPTATION TO DIFFERENT TYPES OF GAS; appliance from the electrical socket.; natural gas; at a pressure of; Removing the hob; Remove the screws and the nuts

Instructions for the installer 29 5 ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, disconnect the appliance from the electrical socket. The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. For functioning with other types of gas the ...

Page 10 - Regulation for LPG

Instructions for the installer 30 5.2 Regulation for LPG Loosen screw A and push support B all the way. Use a double head wrench to remove nozzle C and assemble the suitable one, following the instructions indicated in the reference charts, with respect to the type of gas to use. The screwing torque...

Page 11 - Regulation for natural gas; Regulation for town gas

Instructions for the installer 31 5.3 Regulation for natural gas The hob has been inspected for G20 (2H) natural gas at a pressure of 20 mbar. To allow the unit to work with this type of gas, perform the same operations described in paragraph “5.2 Regulation for LPG”, but choose the nozzles and regu...

Page 12 - Regulation of primary air

Instructions for the installer 32 5.5 Regulation of primary air Referred to distance “ X ” in mm. Burner G20 20 mbar G30/G31 G110 30/37 mbar 8 mbar Auxiliary (1) 1.5 1.0 0.5 Semirapid (2) 1.5 1.5 0.5 Rapid (3) 1.0 1.5 1.0 Rapid large (4) 2.5 10.0 1.5 Fish pan (7) 2.0 2.5 1.0 Ultra rapid (5) 2.0 2.5 ...

Page 13 - FINAL OPERATIONS; Regulation of minimum for natural gas; Regulation for LPG”.

Instructions for the installer 33 6 FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph “5.1 Removing the hob”. 6.1 Regulation of minimum for natural gas Replace the components on the burner and slide the knobs on th...

Page 14 - Arrangement of burners on hob; Burners; Lubrication of gas taps; This must be done by a qualified technician.

Instructions for the installer 34 6.3 Arrangement of burners on hob Burners 1. Auxiliary 2. Semirapid 3. Rapid 4. Rapid large 5. Ultra rapid 6. Double crown 7. Fish pan 6.4 Lubrication of gas taps After a while, the gas tap may become hard to turn or lock. If this happens, it has to be cleaned insid...

Page 15 - Instructions for the user; USING THE HOB; Ignition of the burners

Instructions for the user 35 7 USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B . Grid C (where available) is intended for use with woks (Chinese pans). Adapter D come...

Page 16 - Practical advice for using the burners; Take care not to touch the glass of the lid with hot pots and pans.; Diameter of the pans; Using a griddle plate

Instructions for the user 36 7.2 Practical advice for using the burners For better burner performance and minimum gas consumption, flat bottomed, even pans must be used, with covers and proportional in size to the burners (see paragraph “7.3 Diameter of the pans”). To avoid overcooking or damage to ...

Page 17 - CLEANING AND MAINTENANCE; Never use a steam jet to clean the appliance.; Cleaning; Regular daily cleaning of the hob; pour the product on a damp cloth and wipe the surface,; Food stains or residues

Instructions for the user 37 8 CLEANING AND MAINTENANCE Never use a steam jet to clean the appliance. Before any intervention, disconnect the power supply of the appliance. 8.1 Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning...

Page 18 - Cleaning of cooking hob components; CAUTION: do not wash these components in a dishwasher.; Ignition plugs and safety devices; Check frequently and clean with a damp cloth when necessary.; The cover; and water drips might damage its operation and appearance.

Instructions for the user 38 8.2 Cleaning of cooking hob components CAUTION: do not wash these components in a dishwasher. In normal use of the hob, the stainless steel burner caps and pan- stands tend to be burnished by the high temperature. Clean these parts using very fine abrasive sponges or sim...