Smeg PVS750- Manuals

Page 2 - Precautions for Safety and Use; Precautions for safety and use

Precautions for Safety and Use 22 1. Precautions for safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CYCLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT CONTAINS BEFORE USING THE HOB. ALSO KEEP T...

Page 3 - Instructions for the Installer; Fitting the appliance in the top; Fixing to the supporting structure

Instructions for the Installer 23 2. Fitting the appliance in the top If the hob has to be adapted for a type of gas different from the one for which it is preset in the factory, make this adjusting before building it into the unit, following the instructions in point “5. Adapting to different types...

Page 4 - Fitting the adhesive foam rubber strip; Fitting the fixing clips

Instructions for the Installer 24 2.2 Fitting the adhesive foam rubber strip Fit the adhesive foam rubber strip (supplied with the hob) around the outside edge of its surround. It will act as a cushion between the surface of the surround and that of the cabinet. The diagram on the right shows the co...

Page 5 - Fitting the hob into the hole in the work-top

Instructions for the Installer 25 2.4 Fitting the hob into the hole in the work-top Take special care when fitting the hob into the work-top. If the procedures are not carried out correctly, exactly as described, the hob may be damaged. Before fitting the hob, remove the pan stands (if fitted) and t...

Page 6 - Electrical connection

Instructions for the Installer 26 3. Electrical connection Check that the power supply line voltage and size are as specified on the nameplate underneath the appliance's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same...

Page 7 - Gas connection; Bottled gas connection

Instructions for the Installer 27 4. Gas connection If the appliance is installed above an oven, the gas hose must be passed around the back of the oven to prevent overheating. The connection to the gas mains may be made using a copper pipe or a continuous-wall steel hose in accordance with the rele...

Page 8 - Adapting to different types of gas; Removing the hob skin

Instructions for the Installer 28 5. Adapting to different types of gas The operations described below must be carried out with the appliance not built-in and not connected to the gas or electricity supply. The appliance is tested with G20 (2H) natural gas at the pressure of 20 mbar. If it is to be ...

Page 9 - Adjusting for bottled gas

Instructions for the Installer 29 5.2 Adjusting for bottled gas Undo the screw C and push the air regulator D fully down. Remove the nozzle E with a 7 mm spanner and fit the suitable one, following the instructions in the tables referring to the type of gas to be used. The nozzle must not be tighten...

Page 10 - Adjusting the primary air flow

Instructions for the Installer 30 5.4 Adjusting the primary air flow Refers to the gap “ X ” in mm. BURNER G20 20 mbar G30/G31 30/37 mbar 0.5 9.5 Auxiliary Semi rapid 1 1 2 3 Rapid Ultra Rapid open 4 To identify the burners on your hob, refer to the drawings in point “5.8 Hob burner layout”.

Page 11 - Reassembling the hob skin; Adjusting the minimum setting for natural ga; Adjusting the minimum for bottled gas; Greasing the gas taps

Instructions for the Installer 31 5.5 Reassembling the hob skin Reverse the procedure described in point “5.1 Removing the hob skin”. When replacing the cover plates, check that the seals are fitted correctly. 7.1 Fit the pan stands as described in point Fitting the pan stands. 5.6 Adjusting the min...

Page 12 - Instructions for the User; Description of controls; The front panel

Instructions for the User 32 6. Description of controls 6.1 The front panel All the hob's control and monitoring devices are placed together on the front panel. CONTROL AREA 5 Burner Hob KNOB OPERATING MODE To light the flame, press the knob and at the same time turn it anti-clockwise to the minimum...

Page 13 - Using the hob; Fitting the pan stands

Instructions for the User 33 7. Using the hob Check that the fixing cover plates E , the burners, the flame diffuser rings and the pan stands are fitted correctly. The projections A on the flame diffuser rings must be fitted into the recesses B in the burner. The holes C in the burner must mate with...

Page 16 - Lighting burners with safety device

Instructions for the User 36 7.2 Lighting burners with safety device The burner it controls is shown next to each knob (the example here shows the front left-hand burner). The appliance is equipped with electronic ignition. Simply press the knob and turn it anti-clockwise to the minimum flame symbol...

Page 17 - Cleaning and maintenance; Cleaning the hob; Cleaning instructiona for an acid-et ched glass hob; Cleaning the components

Instructions for the User 37 Cleaning and maintenance Before carrying out any operations, disconnect the appliance from the electricity supply. Never use a jet of steam for cleaning the appliance. 7.5 Cleaning the hob To keep the hob in good condition, it must be cleaned regularly, after each use, f...