Smeg PGF95-2- Manuals

Page 2 - Introduction; INSTRUCTIONS FOR SAFE AND PROPER USE

Introduction 1 INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE HOB. ALSO ...

Page 3 - The manufacturer declines all liability for injury; to persons or animals

Introduction THE APPLIANCE DATA PLATE, WITH TECHNICAL DATA, REGISTRATION NUMBER AND BRAND NAME, IS POSITIONED AT A VISIBLE POINT UNDER THE SAFETY COVER. THE DATA PLATE ON THE PROTECTIVE COVER MUST NEVER BE REMOVED . DO NOT PUT PANS WITHOUT PERFECTLY PERFECTLY SMOOTH AND FLAT BOTTOMS ON THE HOB PANST...

Page 4 - Instructions for the installer; POSITIONING OF THE HOB; Create an opening with the

Instructions for the installer 23 2 POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood, as long as th...

Page 5 - Attachment to support structure, flush-mounting model

Instructions for the installer 4) 24 2.2 Attachment to support structure, flush-mounting model Create an opening with the dimensions shown in the figure in the work surface, observing a minimum distance of 50 mm from the rear edge. 1) The lower part of the protective cover must be fully accessible w...

Page 6 - Apply a layer of “waterproof primer” to the milled surface.

Instructions for the installer 25 4) Mill to this depth for laminated worktops of lessthan 3mm thickness. Apply a layer of “waterproof primer” to the milled surface. Important: Other types of installation will only be possible under themanufacturer's supervision. Overall dimensions: location of gas ...

Page 8 - Electrical connection; Do not; located at an easily accessible position near the appliance.

Instructions for the installer 27 2.3 Electrical connection Make sure that the voltage and capacity of the power supply cable conform to the data shown on the plate located under the protective cover. Do not remove this plate for any reason . The power supply cable plug and the wall socket must be o...

Page 9 - Ventilation requirements

Instructions for the installer 28 2.4 Ventilation requirements The appliance may be installed only in rooms with permanent ventilation, as required by standard regulations in force. The room in which the appliance is installed must have sufficient air flow to satisfy the requirements of normal gas c...

Page 10 - Gas connection; rigid copper pipe; Connection to LPG

Instructions for the installer 29 2.6 Gas connection Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe conforming to the provisions defined by standard regulations in force. After connection operations, check for leaks using a soapy solution. The hob has been i...

Page 11 - ADJUSTMENT TO DIFFERENT TYPES OF GAS; The hob is set for; Replacement of nozzles on the hob; Replace the burners in the correct position.

Instructions for the installer 30 3 ADJUSTMENT TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, unplug theappliance from the mains. The hob is set for natural gas G20 (2H) at a pressure of 20 mbar. In the case of functioning with other types of gas the burner nozzles mus...

Page 12 - Burner and nozzle characteristics table; Arrangement of burners on cooking hob; BURNERS; Auxiliary

Instructions for the installer 31 3.2 Burner and nozzle characteristics table Burner Rated heating capacity (kW) LPG – G30/G31 30/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Reduced flow rate (W) Flow rate g/h G30 Flow rate g/h G31 Auxiliary (1) 1.05 50 30(*) 28 (**) 350 76 75 Semi rapid (2) 1...

Page 13 - FINAL OPERATIONS; Regulation of minimum for town gas and natural gas; This operation must be done

Instructions for the installer 32 4 FINAL OPERATIONS After carrying out the above adjustments, remount in reverse order to the instructions given in paragraph “3.1 Replacement of nozzles on the hob”. After adjustment to a different kind of gas from the one for which the appliance has been tested, re...

Page 14 - Instructions for the user; USING THE HOB; Ignition of the burners; are aligned with the ignition plugs and the

Instructions for the user 5 USING THE HOB 5.1 Ignition of the burners Before turning on the burners, make sure that the flame-spreader crowns and respective caps are properly fitted in their housings. Ensure the flame-spreader holes A are aligned with the ignition plugs and the thermocouples. Pansta...

Page 15 - Practical advice for using the burners

Instructions for the user 34 If the burners turn off accidentally, a safety device will trip after about 20 seconds to cut off gas flow (even with the gas tap open). 5.2 Practical advice for using the burners For better use of the burners and lower gas consumption, use covered cooking receptacles th...

Page 16 - CLEANING AND MAINTENANCE; Before any intervention, disconnect the appliance from the mains.; Cleaning the stainless steel; Routine daily cleaning; To clean and preserve the stainless steel surfaces, always use; only; pour the product on a damp cloth and wipe the surface, rinse; Food stains or residues; Cleaning of cooking hob components; before remounting; align with burner pins

Instructions for the user 6 CLEANING AND MAINTENANCE Before any intervention, disconnect the appliance from the mains. 6.1 Cleaning the stainless steel To keep stainless steel in good condition it should be cleaned regularly after use. Let it cool first. 6.1.1 Routine daily cleaning To clean and pre...