Smeg CS6CMXA - Manuals

Instructions 8 • The appliance must be connected to earth in compliance with electrical system safety standards. • Use cables withstanding a temperature of at least 90 °C. • The tightening torque of the terminal board screws for the power supply wires must be 1.5 - 2 Nm. • If the electrical supply i...

Instructions 9 EN 1.4 Identification plate The identification plate bears the technical data, serial number and brand name of the appliance. Do not remove the identification plate for any reason. 1.5 This user manual This user manual is an integral part of the appliance and must therefore be kept in...

Instructions 10 1.7 How to read the user manual This user manual uses the following reading conventions: 1. Sequence of instructions for use.• Standalone instruction. Instructions General information on this user manual, on safety and final disposal. Description Description of the appliance and its ...

Description 11 EN 2 Description 2.1 General Description 1 Backguard 2 Hob 3 Control panel 4 Oven light 5 Seal 6 Door 7 Storage compartment 8 Fan Rack/tray support frames

Description 12 2.2 Hob * power levels are approximate and may vary according to the settings made and the mains voltage. 2.3 Control panel 1 Hob cooking zone knobs Useful for switching on and adjusting the cooking zones of the hob. Press and turn the knob clockwise to adjust the power of each zone f...

Description 13 EN 3 Temperature knob This knob allows you to select the cooking temperature. Turn the knob clockwise to the required value, between the minimum and maximum setting. 4 Programmer clock Useful for displaying the current time, setting programmed cooking operations and programming the mi...

Description 14 2.5 Available accessories Rack Useful for supporting containers with food during cooking. Tray rack To be placed over the top of the tray; for cooking foods which may drip. Tray Useful for collecting fat from foods placed on the rack above. Deep tray Useful for collecting fat from foo...

Use 15 EN 3 Use 3.1 Instructions High temperature inside the oven during use Danger of burns • Keep the oven door closed during cooking. • Protect your hands wearing heat resistant gloves when moving food inside the oven. • Do not touch the heating elements inside the oven. • Do not pour water direc...

Use 16 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from the accessories and from the oven cavity. 3. Remove and wash all the appliance accessories (see 4 Cleaning and maintenanc...

Use 17 EN Racks and trays Racks and trays have to be inserted into the side guides until they come to a complete stop.• The mechanical safety locks that prevent the rack from being removed accidentally must face downwards and towards the back of the oven cavity. 3.3 Using the hob Residual heat The i...

Use 18 Switching off the cooking zones To switch off the cooking zones, turn the corresponding knobs to 0 . Double heating zones To turn on the double heating zones, turn the knob to the maximum value and then to the symbols or . When the knob is released, it automatically returns to the highest pow...

Use 19 EN Functions list Static As the heat comes from above and below at the same time, this system is particularly suitable for certain types of food. Traditional cooking, also known as static cooking, is suitable for cooking just one dish at a time. Perfect for all types of roasts, bread and cake...

Use 20 3.5 Programmer clock Value decrease key Clock key Increase key Fan with circulaire The combination of the fan and the circulaire heating element (incorporated in the rear of the oven) allows you to cook different foods on several levels, as long as they need the same temperatures and same typ...

Use 21 EN Setting the time On the first use, or after a power failure, the digits will be flashing on the appliance’s display. 1. Hold down the clock key for two seconds. The dot between the hours and the minutes flashes. 2. The time can be set via the value increase key and value decrease key . Kee...

Use 22 7. Press the clock key to reset the programmer clock. Programmed cooking 1. Set the cooking time as described in the previous point “Timed cooking”. 2. Hold the menu key down for 2 seconds. 3. Press the menu key again. The display will show the digits and the text in sequence, while the symbo...

Use 23 EN 10. Return the function and temperature knobs to 0 . 11. To turn off the buzzer just press any key of the programmer clock. 12. Press the and keys at the same time to reset the set program. Minute minder timer The minute minder timer can be activated at any time. 1. Keep the clock key pres...

Use 24 Modifying the set data 1. Press the clock key . 2. Use the value increase and value decrease keys to set the number of minutes required. Deleting the set data 1. Press the clock key . 2. Hold down the value increase and value decrease keys at the same time. 3. Then switch off the oven manuall...

Use 25 EN Advice for cooking with the Grill • Meat can be grilled even when it is put into the cold oven or into the preheated oven if you wish to change the effect of the cooking. • With the Fan with grill function, we recommend that you preheat the oven before grilling. • We recommend placing the ...

Use 26 Cooking information table Food Weight (Kg) Function Shelf Temperature (°C) Time (minutes) Lasagne 3 - 4 Static 1 220 - 230 45 - 50 Pasta bake 3 - 4 Static 1 220 - 230 45 - 50 Veal roast 2 Turbo/Circulaire 2 180 - 190 90 - 100 Pork loin 2 Turbo/Circulaire 2 180 - 190 70 - 80 Sausages 1.5 Fan w...

Cleaning and maintenance 27 EN 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the surfaces To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always and only use specific products that do not contain abrasives or...

Cleaning and maintenance 28 4.3 Cleaning the hob Cleaning the glass ceramic hob Light coloured marks from pans with aluminium bases can be easily cleaned off with a cloth moistened in vinegar.After cooking, remove any burnt residues with the scraper provided; rinse with water and dry thoroughly with...

Cleaning and maintenance 29 EN 4.4 Cleaning the door Removing the door For easier cleaning it is recommended to remove the door and place it on a tea towel.To remove the door proceed as follows:1. Open the door completely and insert two pins into the holes on the hinges indicated in the figure. 2. G...

Cleaning and maintenance 30 Removing the internal glass panes For easier cleaning the internal glass panes of the door can be removed.1. Remove the internal glass pane by pulling the rear part gently upwards, following the movement indicated by the arrows ( 1 ). This way, the 4 pins attached to the ...

Cleaning and maintenance 31 EN 4.5 Cleaning the oven cavity In order to keep your oven in the best possible condition, clean it regularly after letting it cool down.Avoid letting food residue dry inside the oven cavity, as this could damage the enamel.Take out all removable parts. Cleaning the racks...

Cleaning and maintenance 32 Vapor Clean Preliminary operations Before starting the Vapor Clean cycle:• Completely remove all accessories from inside the oven. The upper guard can be left inside the oven. • Pour approx. 40 cc of water onto the floor of the oven. Make sure it does not overflow out of ...

Cleaning and maintenance 33 EN End of the Vapor Clean cycle 4. Open the door and wipe away the less stubborn dirt with a microfibre cloth. 5. Use a non-scratch sponge with brass filaments on hard to remove deposits. 6. In case of grease residues use specific oven cleaning products. 7. Remove the wat...

Cleaning and maintenance 34 Replacing the internal light bulb 1. Completely remove all accessories from inside the oven. 2. Remove the rack/tray support frames.3. Remove the bulb cover using a tool (e.g. a screwdriver). 4. Slide out and remove the light bulb. 5. Replace the light bulb with one of th...

Installation 35 EN 5 Installation 5.1 Positioning This appliance may be installed next to walls, one of which is higher than the worktop, at a minimum distance of X mm from the side of the appliance, as shown in figures “ A ” and “ C ” relative to the installation classes. Any wall units installed a...

Installation 36 B - Class 2 subclass 1 (Built-in appliance) C - Class 2 subclass 1 (Built-in appliance) Appliance overall dimensions 1 Minimum distance from side walls or other flammable material. 2 Minimum cabinet width ( =A ). The appliance must be installed by a qualified technician and according...

Installation 37 EN Appliance dimensions: location of electrical connection (mm) E = Electrical connection Assembling the upstand The upstand must always be positioned and secured correctly on the appliance.1. Loosen the 4 screws ( A ) on the back of the hob (2 for each side) using a screwdriver. 2. ...

Installation 38 Positioning and levelling After making the electrical and/or gas connections, screw the four adjustable legs supplied with the appliance. The appliance must sit level on the floor to ensure stability.Screw or unscrew the bottom part of the leg until the appliance is stable and level ...

Installation 39 EN 3. Assemble the fastening bracket. 4. Align the base of the hook on the fastening bracket with the base of the slot on the wall fastening plate. 5. Align the base of the fastening bracket with the ground and tighten the screws to fix the measurements. 6. Use 50 mm for the distance...

Installation 40 7. Move the bracket onto the wall and mark the position of the holes to be drilled in the wall. 8. After drilling the holes in the wall, use wall plugs and screws to fasten the bracket to the wall. 9. Push the cooker towards the wall, and at the same time, insert the bracket in the p...

Installation 41 EN The appliance can work in the following modes:• 220-240 V 2 ~ 3 x 4 mm² three-core cable. • 220-240 V 3 ~ 4 x 2.5 mm² four-core cable. • 220-240 V 1N ~ 3 x 4 mm² three-core cable. • 380-415 V 2N ~ 4 x 2.5 mm² four-core cable. • 380-415 V 3N ~ 5 x 1.5 mm² five-core cable. Access to...

Installation 42 3. Proceed with installation of the power supply cable. 4. When you have finished, reposition the plate on the rear casing and fasten it in place with the previously removed screws. Fixed connection Fit the power line with an all-pole disconnection switch, with a clearance between it...