Smeg C9IMX2 - User Manual

44 - DESCRIPTION 91477A441/D DESCRIPTION General description 1 Hob2 Control panel 3 Socket for temperature probe (on some models only) 4 Oven light 5 Seal6 Door7 Fans8 Storage compartment Frame shelf Hob Zone Dimensions H x L (mm) Pan Ø min. (mm) Pan Ø recommended (mm) Max. power draw (W)* Power dra...

DESCRIPTION - 45 91477A441/D e * power levels are indicative and can vary according to the pan used or the settings made. Advantages of induction cooking • Energy saving thanks to the direct transmission of energy to the pan (suitable magnetisable cookware is required) compared to traditional electr...

46 - DESCRIPTION 91477A441/D using the temperature knob. Other parts Shelves The appliance features shelves to position trays and racks at different heights. The insertion heights are indicated from the bottom upwards (see General description). Cooling fan The fan cools the oven and comes into opera...

USE - 47 91477A441/D e Protective cover (on some models only) Used to cover and protect the temperature probe socket when the temperature probe is not in use. Self-cleaning panels (on some models only) Useful for absorbing small grease residues. USE Preliminary operations • Remove any protective fil...

50 - USE 91477A441/D Hob power limitation The induction hob is configured to operate at 7.4 kW, but it can be set to operate at 4.8 kW or 3.7 kW.1. Disconnect the appliance from the mains power supply and wait 10 seconds before turning the power back on. 2. Turn both the front left and front right c...

USE - 51 91477A441/D e FAN-ASSISTED BASE SMALL GRILL GRILL FAN WITH GRILL FAN ASSISTED CIRCULAIRE BOTTOM HEAT RAPID DEFROST ECO VAPOR CLEAN (on some models only) Digital programmer Decrease key Clock key Increase key Setting the time On the first use, or after a power failure, the digits will be fla...

54 - USE 91477A441/D Cooking using the temperature probe With preheating:1. Set manual cooking (see “Using the oven”).2. After preheating, open the door and insert the tray onto which the food has been placed into the appropriate guides. 3. Insert the plug of the probe into the socket at the side, u...

USE - 55 91477A441/D e undercooked on the inside). Advice for cooking meat • Cooking times vary according to the thickness and quality of the food and to consumer taste. • Turn the food to brown on both sides.• Use a meat thermometer when roasting meat, or simply press on the roast with a spoon. If ...

CLEANING AND MAINTENANCE - 57 91477A441/D e Temperature probe-cooking information table (on some models only) CLEANING AND MAINTENANCE Cleaning the appliance Cleaning the surfaces To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily ...

58 - CLEANING AND MAINTENANCE 91477A441/D wooden or plastic tool, if necessary. Rinse thoroughly and dry with a soft cloth or a microfibre cloth.Do not allow residues of sugary foods (such as jam) to set inside the oven. If left to set for too long, they might damage the enamel lining of the oven. C...

60 - CLEANING AND MAINTENANCE 91477A441/D insert the 2 rear pins into their seats by pressing lightly. Cleaning the oven cavity In order to keep your oven in the best possible condition, clean it regularly after letting it cool down.Avoid letting food residue dry inside the oven cavity, as this coul...

CLEANING AND MAINTENANCE - 61 91477A441/D e slide it out of the seats B at the back. • When cleaning is complete, repeat the above procedures to put the rack/tray support frames back in. Vapor Clean (on some models only) Preliminary operations Before starting the Vapor Clean cycle: • Completely remo...

62 - INSTALLATION 91477A441/D 2. Remove the rack/tray support frames.3. Use a tool (e.g. a spoon) to remove the bulb cover. 4. Slide out and remove the light bulb. 5. Replace the light bulb with one of the same type (40 W). 6. Refit the cover. Ensure the moulded part of the glass (A) is facing the d...

64 - INSTALLATION 91477A441/D 3. Assemble the fastening bracket. 4. Align the base of the hook on the fastening bracket with the base of the slot on the wall fastening plate. 5. Align the base of the fastening bracket with the ground and tighten the screws to fix the measurements. 6. Consider a dist...

66 - INSTALLATION 91477A441/D Instructions for the installer • If you use a plug (if present) to connect to the power supply, the plug must be accessible after installation. • Do not bend or trap the power cable.• The appliance must be installed according to the installation diagrams. • If the appli...