Shop Fox W1850 - Manuals

-6- Model W1850 (For Machines Mfd. Since 06/17) SA FE T Y Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,. MAY.result.in.minor.or.moderate.injury. Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,. WILL.result.in.death.or.serious.injury. Indicates.a.potentially.ha...

-8- Model W1850 (For Machines Mfd. Since 06/17) SA FE T Y Additional.Safety.for.Belt.&.Disc.Sanders Serious injury or death can occur if fingers, clothing, jewelry, or hair get entangled in moving components. Impact injuries can occur from kickback if workpiece is improperly fed into moving sand...

-9- Model W1850 (For Machines Mfd. Since 06/17) EL EC TR IC A L ELECTRICAL Circuit.Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is a...

-10- Model W1850 (For Machines Mfd. Since 06/17) EL EC TR IC A L Grounding.Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric sho...

-11- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Unpacking SETUP This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. SUFFOCATION HAZARD! Immediately discard a...

-12- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Inventory:.(Figures.2–3). Qty A.. Motor and Base ............................................1 B.. Belt Housing Assembly ....................................1 C.. Belt Table ...................................................1 D.. Aluminum San...

-13- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Hex Wrench 16mm MEASURE BOL T DIAMETER BY PLACING INSIDE CIRCLE 7 ⁄ 16 " 3 ⁄ 8 " 1 ⁄ 4 " 5 ⁄ 16 " #10 1 ⁄ 2 " W ASHERS ARE MEASURED BY THE INSIDE DIAMETER USE THIS CHART TO IDENTIFY HARDWARE DURING THE INVENTORY/ASSEMBLY PR...

-14- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Cleaning.Machine Machine.Placement Workbench.Load Refer to the Machine.Specifications for the weight and footprint specifications of your machine. Some workbenches may require additional reinforcement to support the weight of the machine and w...

-15- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Bench.Mounting Number.of.Mounting.Holes................................... 4 Diameter.of.Mounting.Hardware.Needed............... 1 ⁄ 2 " Machine Base Workbench Bolt Flat Washer Flat Washer Lock WasherHex Nut Rubber Foot Figure.5. Typical &...

-16- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Assembly Before beginning the assembly process, refer to Items Needed for Setup and gather the items you will need. Ensure all parts have been properly cleaned of any heavy-duty rust-preventative applied at the factory (if applicable). Be sure...

-17- Model W1850 (For Machines Mfd. Since 06/17) SE TU P 5. Position belt housing assembly so there is about 1 ⁄ 4 " V-belt deflection when moderate pressure is applied to V-belt between pulleys (see Figure.11 ) then fully tighten cap screws from Step 3 to secure belt housing assembly in place. ...

-18- Model W1850 (For Machines Mfd. Since 06/17) SE TU P 11. Rotate disc until set screw is visible through hole on back of V-belt safety cover and use 2.5mm hex wrench to secure disc to motor arbor (see Figure.14 ). Figure.16. Using thin cardboard ( 1 ⁄ 16 " thick) for clearance gauge. 12. Inst...

-21- Model W1850 (For Machines Mfd. Since 06/17) SE TU P Figure.24. Removing switch key from toggle switch. Test.Run Serious. injury. or. death. can. result. from. using. this. machine. BEFORE. understanding. its. controls. and. related. safety.information..DO.NOT.operate,.or. allow. others. to. ope...

-22- Model W1850 (For Machines Mfd. Since 06/17) O PE R ATIO NS OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written w...

-23- Model W1850 (For Machines Mfd. Since 06/17) O PE R ATIONS Disc.Sanding To.perform.sanding.operations.with.the.sanding.disc,. do.these.steps: 1. DISCONNECT MACHINE FROM POWER! 2.. Adjust angles of disc sanding table and miter gauge for operation. 3. Connect sander to power, turn it ON , and allo...

-25- Model W1850 (For Machines Mfd. Since 06/17) O PE R ATIONS ACCESSORIES Belt.&.Disc.Sander.Accessories The following belt & disc sander accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also av...

-27- Model W1850 (For Machines Mfd. Since 06/17) M A INTEN A N CE MAINTENANCE Cleaning the Model W1850 is relatively easy. Vacuum excess sawdust, and wipe off the remaining dust with a dry cloth. Wiping the table clean after every use ensures moisture from wood dust does not remain on bare metal sur...

-28- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E Sanding.Belt.Tracking The sanding belt must track in the center of the top pulley to avoid damage during use. To.adjust.sanding.belt.tracking,.do.these.steps: 1. DISCONNECT MACHINE FROM POWER! 2. While facing tracking adjustment knob, turn ...

-29- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E Changing.Sandpaper.Disc The Model W1850 accepts 8" diameter cloth or paper- backed, pressure-sensitive adhesive (PSA) sandpaper discs (refer to Accessories on Page.25 ). Refer to the Assembly subsection, beginning on Page.16 , for detai...

-30- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E Tensioning/Replacing. V-Belt 1. DISCONNECT MACHINE FROM POWER! 2. Remove disc table, dust port, dust cover, and V-belt safety cover (refer to Assembly steps beginning on Page 16). 1. DISCONNECT MACHINE FROM POWER! 2. Remove disc table, dust...

-31- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E Troubleshooting Motor.&.Electrical PROBLEM POSSIBLE.CAUSE CORRECTIVE.ACTION Machine does not start or a breaker trips. 1. Switch disabling key removed.2. Power supply switched OFF or at fault.3. Plug/receptacle at fault/wired wrong. 4. ...

-33- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E Electrical.Safety.Instructions SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, o...

-34- Model W1850 (For Machines Mfd. Since 06/17) SE RV IC E STOP Read Page 33 Before Wiring Wiring.Diagram This. motor. wiring. diagram. is. current. at. the. time. of. printing;. however,. always. use. the. diagram. on. the. inside. of. the. junction. box. cover. when. rewiring. your. motor! BLACK ...

-35- Model W1850 (For Machines Mfd. Since 06/17) PA RT S 22 23 24 25 26 27 28 29 30 32 33 34 35 36 37 38 39 41 43 45 46 47 48 49 50 51 52 64 65 66 6768 69 72 80 81 1 2 3 4 5 6 7 8 9 12 13 14 15 16 18 10 11 19 20 21 53 54 55 57 58 59 56 62 63 61 60 70 71 17 56-1 56-2 39 41 38 110 120 121 122 123 124 ...

tape along edges--please do not staple Fold along dotted lIne Fold along dotted lIne Woodstock international inc. p.o. box 2309 bellingham, Wa 98227-2309 place stamp Here

WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neglige...