Shop Fox W1668 - Manuals

-6- W1668 13 1 ⁄ 4 " Oscillating Drill Press SA FE T Y Additional Safety for Drill Presses 1. EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is recommended. Always keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO NOT wear gloves ...

-7- W1668 13 1 ⁄ 4 " Oscillating Drill Press SA FE T Y Figure 3 . Keep fingers away from spinning drill bits, cutters, and sanding surfaces. Figure 1 . Never drill while holding the workpiece by hand. Figure 2 . Remove switch safety key when not in use. Figure 4 . Remove handles when using the o...

-8- W1668 13 1 ⁄ 4 " Oscillating Drill Press EL EC TR IC A L DO NOT work on your electrical system if you are unsure about electrical codes and wiring! Seek assistance from a qualified electrician. Ignoring this warning can cause electrocution, fire, or machine damage. ELECTRICAL 110V Operation ...

-9- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P Keep machine disconnected from power until instructed otherwise. This machine has been carefully packaged for safe trans- portation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer imm...

-10- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P Figure 8 . Using holes as a drill guide. Figure 9 . Installing the dust port. The dust port directs suction to the sanding sleeve, removing hazardous dust and increasing abrasive life. To install the dust port, do these steps: 1. Bring the du...

-11- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P To install the table support, do these steps: 1. Insert the 12mm lock handle into the table support bracket through the blind hole, into the threaded hole, and thread inward three turns, as shown in Figure 10 . 2. If the pinion is not already...

-12- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P Figure 13. Rack, column, table support position. Figure 14 . Column ring bevel positioning. Figure 15 . Table installation. 6. Position the rack so the long un-toothed end is facing upward (see Figure 13 ). 7. Insert the rack into the table s...

-13- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P Figure 17 . Aligning headstock with base. Figure 18 . Securing the headstock to the column. Set Screws Figure 16. Aligning the pocket in the headstock with the column. Belt Cover Knob To install the headstock, do these steps: 1. With an assis...

-14- W1668 13 1 ⁄ 4 " Oscillating Drill Press SE TU P Figure 21 . Installing spindle handles. Figure 20 . Inserting the hex cap screw. Figure 19 . Jaws adjusted inside chuck body. The drill chuck is seated to the spindle with a JT-33 tapered surface and a screw. To install the drill chuck, do th...

-15- W1668 13 1 ⁄ 4 " Oscillating Drill Press A D JU ST M ENTS The drill press main drive belts last a long time; however, during machine life, a belt may stretch slightly which can cause the pulleys to slip under a load. You will then need to adjust the motor-to-idler pulley belt tension to com...

-16- W1668 13 1 ⁄ 4 " Oscillating Drill Press A D JU ST M ENT S The feed shaft return spring is adjusted at the factory; however, during the life of the drill press you may want to adjust the feed shaft return spring to a stronger return pressure. To adjust the feed shaft spring tension, do thes...

-18- W1668 13 1 ⁄ 4 " Oscillating Drill Press A D JU ST M ENT S To adjust the table, do these steps: 1. Loosen the table lock lever. 2. Turn the hand crank to raise or lower the table, as shown in Figure 30 . 3. Position the table so the opening in the installed table insert is centered to the d...

-19- W1668 13 1 ⁄ 4 " Oscillating Drill Press A D JU ST M ENTS To change the drilling speed, do these steps: 1. UNPLUG THE DRILL PRESS! 2. Refer to the speed chart located under the belt cover or refer to the “ Drill Press RPM Chart” on Page 20, and choose the desired speed. 3. Loosen the motor ...

-20- W1668 13 1 ⁄ 4 " Oscillating Drill Press A D JU ST M ENT S Use Figure 35 to select the optimum motor-to-spindle pulley ratio for drilling, cutting, and sanding operations. The belt setting in the example in Figure 36 shows the spindle belt in the #1 spindle pulley position and the motor bel...

-23- W1668 13 1 ⁄ 4 " Oscillating Drill Press O PE R ATIONS Once assembly is complete and adjustments are done to your satisfaction, you are ready to start the drill press. Every time you start the drill press, you should follow these basic instructions. To start the drill press, do these steps:...

-25- W1668 13 1 ⁄ 4 " Oscillating Drill Press O PE R ATIONS One of the great features of the Model W1668 13 1 ⁄ 4 '' Oscillating Drill Press is its sanding capa- bility. The drill press can be converted from drilling operations to sanding operations in just a few steps. To use the oscillating fe...

-27- W1668 13 1 ⁄ 4 " Oscillating Drill Press M A INTEN A N CE NOTICE Contrary to some beliefs, worn abrasives are not the equivalent the next finer grit abrasive. Discard worn sanding sleeves and avoid the temptation to use them beyond their usable life. Keep the table and other unpainted surfa...

-28- W1668 13 1 ⁄ 4 " Oscillating Drill Press M A INTE N A N CE Troubleshooting Use this table to isolate and correct any problems with your drill press. If you cannot correct a problem, contact Woodstock International, Inc. at 1-360-734-3482 or [email protected]. Page 17

-29- W1668 13 1 ⁄ 4 " Oscillating Drill Press M A INTEN A N CE Wiring Diagram

-30- W1668 13 1 ⁄ 4 " Oscillating Drill Press M A INTE N A N CE SHOP FOX Drill Press Vises use precision ground steel guide rods, smooth-action Acme threads, ground steel jaws, with fixed jaw V-grooves for holding round stock, and dovetailed ways where appli- cable. D2727 SHOP FOX ® (3" Basi...

-32- W1668 13 1 ⁄ 4 " Oscillating Drill Press PA RT S 7A PARTS W1668 Parts Breakdown

-33- W1668 13 1 ⁄ 4 " Oscillating Drill Press PA RT S Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 X1668001 BASE 57 X1668057 PUSH ROD 3 X1668003 COLUMN 58 X1668058 SPRING 5 X1668003-1 COLUMN & COLUMN FLANGE ASSEMBLY 59 X1668059 RUBBER WASHER 6 XPB32M HEX BOLT M10-1.5 X 25 60 X1...

CUT ALONG DOTTED LINE Name ___________________________________________________________________________________Street __________________________________________________________________________________City _________________________ State ___________________________ Zip ________________________Phone # ...