Ridgid OL50145MW - Manuals

Ridgid OL50145MW – Manual in PDF format online.

Manuals:

Manual

Manual Ridgid OL50145MW

Summary

Page 2 - and One World Technologies,; DISCLAIMER OF WARRANTIES; disclaims any liabilities

 Introduction.......................................................................................................................................................................  General Safety Rules ..................................................................................................

Page 3 - GENERAL SAFETY RULES; ELECTRICAL SAFETY; increased risk of electric shock if your body is grounded.; PERSONAL SAFETY

3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. SAVE THESE INSTRUCTIONSWORK AREA  Keep your work area clean and well lit. Cluttered benches and dark areas invite...

Page 5 - SYMbOLS; SYMbOL

5 SYMbOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer. Read The Operator’s Manual Risk of Bursting Risk of Fire or Explosion SYMbOL NAME DESIGNATIO...

Page 6 - SERVICE; customer service for; SAVE THESE INSTRUCTIONS

6 SYMbOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic-ing, use only identical replacement parts. WARNING: To avoid...

Page 7 - EXTENSION CORDS; Cord Length; ELECTRICAL CONNECTION; power supply that is 120 V, AC; SPEED AND WIRING; The no-load speed of this product is approxima; GROUNDING INSTRUCTIONS; ELECTRICAL; GroundinG

7 EXTENSION CORDS Use only 3-wire extension cords that have 3-prong ground-ing plugs and 3-pole receptacles that accept the product’s plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An un...

Page 8 - GLOSSARY OF TERMS

8 GLOSSARY OF TERMS Pressure Regulator KnobRegulates the outgoing pressure from the air outlet to the tool. It is possible to increase or decrease the pressure at the outlet by adjusting this control knob.Pressure SwitchAutomatically controls the on/off cycling of the compressor. It stops the compre...

Page 9 - FEATURES; PRODUCT SPECIFICATIONS; The safe use; DRAIN VALVE; Drain valves are located on both

9 0 0 2 4 50 100 150 230 200 bar 100 0 0 16 5 50 150 200 230 bar psi ON OFF O I 1 TM 2 MINI WHEELBARROW COMPRESSOR OIL LUBE PUMP - POMPE A HULE - BOMBA CON LUBRIC ACION DE ACI ETE 5 Gallon 18,8 Litre 18,7 Litro 4.4 SCFM @ 90PSI 0,12 m /Min @ 621 kPa 0,12 m /Min @ 6,21 bar 145 Max PSI 999 KpA 9,99 ba...

Page 10 - UNPACKING; anual; ASSEMbLY; screw; INSTALLING THE HANDLES

0 0 2 4 6 40 80 120 160 bar 0 2 4 6 40 80 120 160 bar ON OFF O I 1 TM 2 MINI WHEELBARROW COMPRESSOR OIL LUBE PUMP - POMPE A HULE - BOMBA CON LUBRICACION DE ACI ETE 5 Gallon 18,8 Litre 18,7 Litro 4.4 SCFM @ 90PSI 0,12 m /Min @ 621 kPa 0,12 m /Min @ 6,21 bar 145 Max PSI 999 KpA 9,99 bar 3 3 TA NQ UE -...

Page 11 - INSTALLING THE DIPSTICK; Checking the Oil; CHECKING THE OIL; NOTE: Never let the oil drop to a level lower than MIN.; INSTALLING THE SEMI-PNEUMATIC TIRE

ASSEMbLY INSTALLING THE DIPSTICK See Figure 4. The air compressor has a label installed between the oil fill hole and a travel cap. Before using the unit the first time, remove travel cap and label and insert supplied dipstick. Make sure to add oil before first use. See Checking the Oil before first...

Page 12 - OPERATION; APPLICATIONS; ON position to power the compressor on.; USING THE AIR COMPRESSOR

ON OFF O I ON 0 2 4 6 40 80 120 160 bar 0 2 4 6 40 80 120 160 bar 1 TM 2 MINI WHEELBARROW COMPRESSOR OIL LUBE PUMP - POMPE A HULE - BOMBA CON LUBRICACION DE AC IETE OPERATION DANGER: Do not disassemble check valve, tank drain valves or safety relief valve with air in tank — bleed tanks. WARNING: Do ...

Page 13 - DRAINING THE TANKS

3 0 0 2 4 50 100 150 230 200 bar 100 0 0 16 5 50 150 200 230 bar psi TM 2 MINI WHEELBARROW COMPRESSOR OIL LUBE PUMP - POMPE A HULE - BOMBA CON LUBRICACION DE AC IETE  Attach /4 in. NPT male connector fitting to accessory or tool you intend to use.  Insert the other end of the male connector to the...

Page 14 - CHECKING THE SAFETY VALVE; Turn the air compressor on and allow the tanks to fill. The; safetY ValVe; RESET bUTTON; Turn the air compressor off.

4 CHECKING THE SAFETY VALVE See Figure 12. DANGER: Do not attempt to tamper with the safety valve. Anything loosened from this device could fly up and hit you. Failure to heed this warning could result in death or serious personal injury. The safety valve will automatically release air if the air ta...

Page 15 - MAINTENANCE; When servicing use only identical RIDGID; GENERAL MAINTENANCE; To install new semi-pneumatic tire, see; Installing the; Assembly; air filter

5 ON OFF O I ON MAINTENANCE WARNING: When servicing use only identical RIDGID ® replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operatio...

Page 16 - drain PluG; CHANGING THE OIL; diPstick

6 ON OFF O I ON MAINTENANCE Fig. 5 drain PluG oil fill hole collect used oil in a suitable container CHANGING THE OIL See Figure 15. Replace the oil after the first 00 hours of operation and every 00 hours following the first oil change.  Place a suitable container underneath the drain to collect u...

Page 17 - TROUbLESHOOTING; PRObLEM

7 TROUbLESHOOTING PRObLEM CAUSE SOLUTION Compressor will not run Loss of power or overheating No electrical power Blown shop/house fuseShop/house breaker open Thermal overload openPressure switch badTank is full of air Check for proper use of extension cordCheck to be sure unit is plugged in Check f...

Page 18 - WARRANTY

8 Proof of purchase must be presented when requesting war-ranty service. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technolo-gies, Inc., attn: RIDGID Hand Held and Stationary Pow...

Page 19 - NOTES

Page 20 - Customer Service Information:; For parts or service, contact your nearest RIDGID; OPERATOR’S MANUAL; GALLON PORTAbLE

0 Customer Service Information: For parts or service, contact your nearest RIDGID ® authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call -800-4-RIDGID or visit us online at www.ridgid...