Ridgid JP06101 - Manuals

5 • If any part is missing, bent or broken in any way, or any electrical part does not work properly, turn the jointer/planer off and unplug the jointer/planer. • Replace damaged, missing or failed parts before using the jointer/planer again. • Make sure the cutter guard works properly. With the swi...

6 Safety Instructions For Jointer/Planer (continued) • When jointing or rabbeting: - Never joint or bevel workpieces less than 3/4 inch wide or 1/4 inch thick. - Always use the hold-down/push-blocks when jointing or beveling wood whenever possible. - When rabbeting, always make cuts in 1/8" incr...

7 Glossary of Terms for Woodworking Bed The combination of infeed and outfeed table surfaceswhich support the workpiece during a cutting operation. Bevel/Chamfer Removing wood along the edge of a board to make thatedge straight, smooth and angled to the board face whichis against the fence.Cutter Gu...

8 Motor Specifications and Electrical Requirements (continued) General Electrical Connections DANGER: To reduce the risk of electrocution: 1. Use only identical replacement parts when servic- ing. Servicing should be performed by a qualifiedservice technician. 2. Do not use in rain or where floor is...

10 Unpacking and Checking Contents Tools Needed Unpacking WARNING: To reduce the risk of injury from unex-pected starting or electrical shock, do not plug thepower cord into a power source outlet during unpack-ing, until all assembly steps are complete, and youhave read and understand the safety and...

11 Loose Parts E D L G H F A J N B K M P S Q T U R C

12 Unpacking and Checking Contents (continued) Loose Parts (From Hardware Pack) Serrated Hex Bolt (3) Leveling Feet (4) Switch Key (1) Hex Nut (8) Wrench Hex-“L” 3mm (1) Serrated Flange Hex Nut (22) 3/8-16 x 3/4" Screw Pan Head (1) w/Washer 1/4-20 x 5/8 Wrench Box 8mm/10mm (1) 3/8-16 Wire Nut (1...

13 Assembly WARNING: This tool is heavy. To reduce the risk ofback injury, get help whenever you have to lift the tool. Cabinet and Motor Mount Assembly 1. From the hardware pack find the following: 6 Carriage Head Bolts 5/16-18 x 1/2" 6 Serrated Flange Hex Nut 5/16 From among the loose parts fi...

20 Getting to Know Your Jointer/Planer WARNING: For your own safety turn switch “OFF” and remove plug from power source outlet before making any adjustments. 1. Dust Chute with Tool Storage Allows 4" diameter dust collection hose. Easily slides up and out of the way when a vacuum is not con- nec...

22 Alignments Cutter Knife Alignment/Adjustments WARNING: The cutter knives are extremely sharp. Do not let your hand or fingers touch the cutter knives to prevent serious personal injury. Tools Needed 8mm open end wrench and 3mm Allen wrench (supplied).Metal straightedge • Unplug jointer/planer. WA...

23 Cutter Knife Sharpening The knives can be honed individually with an ordinary oil- stone.Make sure your oilstone is not worn in the center. It must be flat.Be sure to remove the burr on the flat side. WARNING: The cutter knives are extremely sharp. Do not let your hand or fingers touch the cutter...

24 Alignments (continued) Outfeed Table Adjustment To check this alignment proceed as follows: WARNING: To reduce the risk of injury from acci- dental start, make sure switch is “OFF” and plug is not connected to power source outlet. NOTE: The outfeed table is adjusted at the factory and should not ...

26 Alignments (continued) To set the fence to 90° simply pivot the fence slightly for- ward of 90°, flip the 90° stop bar into place and pivot the fence back until it contacts the 90° stop and lock into place. The fence may need to be repositioned, using the slide lock knob, over the cutterhead to p...

28 Safety Instructions for Basic Jointer/Planer Operation (continued) Plan Ahead to Protect Your Eyes, Hands, Face and Ears Dress for safety • Plan ahead to protect your eyes, hands, face, ears.• Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and ...

29 Basic Jointer/Planer Cutting Operations Depth of Cut Handwheel Operation Turning the handwheel clockwise will lower the infeed table. This will cause more wood to be removed from the workpiece during the cutting operation.Turning the handwheel counterclockwise will raise the infeed table causing ...

32 WARNING: If the hold-down/push-blocks tend to slip while feeding, clean rubber surface immediately with sandpaper to prevent serious personal injury. When planing wood between 1/2 inch and 3/4 of an inch thick and narrower than the hold-down/push-block, tilt the hold-down/push-block so that it cl...

33 Maintenance and Lubrication Maintenance Do not allow pitch to accumulate on the tables, the fence, the cutter guard, the cutterhead or the knives. Clean them with an appropriate solvent.Apply a thin coat of paste type wax to the tables and the fence so that the wood slides easily while feeding. T...

34 Troubleshooting Guide WARNING: For your own safety, turn switch “OFF” and remove plug from power source outlet before trouble-shooting your jointer/planer. General Trouble Probable Cause Remedy Motor will not run 1. Defective On-Off switch Defective capacitorDefective motor 2. Low line voltage3. ...

35 Motor NOTE: Motors used on wood working tools are particularly susceptible to the accumulation of sawdust and wood chipsand should be blown out or “vacuumed” frequently to prevent interference with normal motor ventilation. Trouble Probable Cause Remedy Excessive noise 1. Motor 2. Pulley set scre...

36 Repair Parts Parts List for RIDGID 6-1/8" Jointer/Planer Model No. JP06101 RIDGID parts are available on-line at www.ridgidparts.com Figure 1 1 2 3 10 5 6 7 8 17 11 15 13 14 15 16 9 4 18 19 20 22 23 12 9 24 25 26 27 28 29 30 31 37 36 39 35 38 40 20 44 43 41 42 13 12 11 21 32 35 34 14 33 45

38 Repair Parts Parts List for RIDGID 6-1/8" Jointer/Planer Model No. JP06101 RIDGID parts are available on-line at www.ridgidparts.com Figure 2 9 1 2 6 7 8 10 11 12 17 17 19 20 21 22 23 24 25 26 27 16 3 4 30 13 18 28 29 31 16 12 11 31 16 14 15 32

40 Repair Parts Parts List for RIDGID 6-1/8" Jointer/Planer Model No. JP06101 RIDGID parts are available on-line at www.ridgidparts.com Figure 3 5 1 2 3 4 5 6 7 7 6 2 7 8 11 9 10 12 13 14 6 9 10 7 6 16 15 6 7 17 18 19 17 18 19

42 Repair Parts Parts List for RIDGID 6-1/8" Jointer/Planer Model No. JP06101 RIDGID parts are available on-line at www.ridgidparts.com Figure 4 Always order by Part Number - Not by Key Number † These parts are available where you purchased your jointer. 1 2 3 4 5 6 7 8 9 10 11 12 13 10 11 14 8 ...

43 Repair Parts Parts List for RIDGID 6-1/8" Jointer/Planer Model No. JP06101 RIDGID parts are available on-line at www.ridgidparts.com Figure 5 Always order by Part Number - Not by Key Number * Standard hardware item, may be purchased locally 13 14 15 17 19 18 1 2 3 4 5 7 6 12 8 9 10 11 16 20 2...