Ridgid AC99401 - Manuals - manualsarea.com

Page 3 - RULES FOR SAFE OPERATION; READ ALL INSTRUCTIONS

3 RULES FOR SAFE OPERATION Safe operation of this accessory requires that you read and understand this operator's manual, the operator’s manual for the miter saw and all labels affixed to the tool. READ ALL INSTRUCTIONS n KNOW YOUR ACCESSORY. Read the operator's manual carefully. Learn the product's...

Page 4 - SYMBOLS; SAVE THESE INSTRUCTIONS; SAFETY AND INTERNATIONAL SYMBOLS; SYMBOL; MEANING

4 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are no...

Page 5 - UNPACKING; TOOLS NEEDED

5 UNPACKING NOTE: Before beginning assembly, check that all parts are included. If you are missing any part, do not assemble this accessory. Call 1-800-4-RIDGID or E-mail us at [email protected] to get the missing part. Sometimes n Stand Assembly (1) n Roller Assembly (2) n Wheels (2) n Ope...

Page 6 - ASSEMBLY; ATTACHING THE LOWER FOOT

6 ASSEMBLY ATTACHING THE LOWER FOOT See Figures 1 d 2. n Place stand assembly “flat” on floor. n Rotate lower foot into upright position aligning holes as shown. n Locate the following parts: Hex Bolt, M8 x 50 mm (2) Flat Washer, M8 (4) Lock Nut, M8 (2) n Install bolt, two washers and lock nut as sh...

Page 7 - SETTING UP

7 WORKSTAND SET-UP See Figures 4 - 5. Before You Start n If a miter saw is already assembled to the stand, make sure that it is securely attached to the stand per the instructions in this manual. n If a compound miter saw is already assembled to the stand, make sure to place the blade 90° to the tab...

Page 8 - MOUNTING MITER SAW; RIDGID MOUNTING HOLES

8 ASSEMBLY MOUNTING MITER SAW See Figures 6 - 7. WARNING: Failure to unplug the tool could result in accidental starting causing possible serious personal injury. Before You Start RIDGID miter saws bolt directly onto this workstand.When you are finished attaching your saw to the workstand reread the...

Page 9 - MOUNTING OTHER BRANDS; MOUNTING AND ALIGNING ROLLER ASSEMBLY

9 ASSEMBLY MOUNTING OTHER BRANDS See Figure 8. NOTE: Other brands of miter saws (not RIDGID miter saws) will require additional 5/16 in. mounting holes to be drilled. See instructions below. n Locate the following parts:Hex Bolts, M6 x 40mm (4) Flat Washers, M6 (4) Fender Washers, M6 (4) Lock Nuts, ...

Page 11 - FOLDING LEG AND TABLE; FOLDING AND MOVING WORKSTAND

11 Before You Start n Remove any workpieces, clamps or other accessories. n Make sure miter saw is securely attached to the stand per the instructions in this manual. n If a miter saw is already assembled to the stand, make sure to place the blade 90° to the table (if applicable), miter the blade to...

Page 12 - TRANSPORTING TOOL

12 ASSEMBLY TRANSPORTING TOOL See Figure 15. n When hauling the workstand in a vehicle, securely tie it down to prevent movement and possible damage. n Always get help if you need to lift the workstand. When lifting, hold the workstand close to your body. Bend your knees so you can lift with your le...

Page 13 - EXPLODED VIEW/REPAIR PARTS; Miter Saw Utility Vehicle Model AC99401

13 EXPLODED VIEW/REPAIR PARTS Miter Saw Utility Vehicle Model AC99401 RIDGID parts are at www.ridgidparts.com 1 829859 Rear Roller Extension 2 829758-5 Washer (20 x 10.5 x 1.5) 3 829759-3 Nylock Nut (M10) 4 829799 Rubber Cap 5 829757-6 Hex Head Bolt (M8 x 1.25 x 33) 6 830256 Table 7 829871-1 Compres...

Page 14 - NOTES

Page 15 - WARRANTY

15 WARRANTY Proof of purchase must be presented when requesting war-ranty service. Limited to RIDGID ® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications...

Page 16 - Customer Service Information:; OPERATOR’S MANUAL; Miter Saw Utility Vehicle; For Use With RIDGID 10 in. and

16 Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid...