Rangemaster Toledo FS Hob - Manuals

5 U18900-02 If a burner flame goes out, turn the control knob off and leave it for one minute before relighting it. You can remove the burner parts for cleaning; see the ‘Cleaning your hotplate’ section of the instructions. You should wipe the top surface of the hotplate around the hotplate burners as...

U108900 - 02 8 Cleaning your hotplate Essential information Before thorough cleaning isolate the electricity supply. Remember to switch on the electricity supply before using the hotplate. Never use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cle...

9 U18900-02 A electrode notch B ignition electrode Now fit the two burner caps, making sure that they are sitting down properly. Cleaning TableHotplate Part Finish Recommended Cleaning Method Hotplate Top Enamel or Stainless Steel Hot soapy water, soft cloth. Any stubborn stains remove gently with a ...

U108900 - 02 10 Troubleshooting What cleaning materials are recommended for the hotplate? See the ‘Cleaning’ section for recommended cleaning materials. We do not recommend Mr. Muscle, as it contains chemicals that may damage the surfaces of your hotplate. If there is an installation problem and I d...

11 U18900-02 Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleansers can produce noxious fumes if applied to a hot surface. Do not use unstable saucepans and position the handles away from the edge of the hotplate. Babies,...

U108900-02 12 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Installation Dear Installer Before you start your installation, please complete the details BELOW. If your customer has a problem relating to your installation they will be able to contact you ea...

13 U108900-02 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. kit. After converting the appliance please attach the Gas Conversion sticker over the appropriate area of the data badge, this will identify the gas type the appliance is now set for. This applia...

U108900-02 14 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. We cannot accept responsibility for damage caused by normal use of the hotplate to any material that de-laminates or discolours at temperatures less than 65°C above room temperature.For safety re...

15 U108900-02 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. For LP Gas it should be capable of 50mbar pressure, 70°C temperature rise and carry a red stripe, band or label. WARNINGS: Ensure that the gas supply pipe is never able to touch moveable parts of...

U108900-02 16 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. If a replacement cable is fitted it must be 250v high temperature rubber/synthetic of 0.75mm 2 minimum conductor size. Connect the replacement cable to the terminal block on the hotplate as shown....

17 U108900-02 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Conversion to LP gas Check in the Technical Data section at the back of the book that the hotplate is convertible to ...

U108900-2 18 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Stick on label Stick the LP gas label over the natural gas part of the appliance data label. Pressure Testing Connect ...

19 U108900-02 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.

U108900 - 02 20 Circuit Diagram L N L N Warmer Switch Warmer Element Mains Terminal Block Spark Generator Ignition Swirches or bk b y b w w bk bk Warmer Neon bk D C1 A B C2 C3 Connection shown in circuit diagram is for single phase. Ratings are for 230V 50Hz Code Item A Ignition generator B Ignition...

21 U18900-02 Technical Data The hotplate is an independent Class 3 built in unit.This hotplate is category II 2H3+ It is supplied set for group H natural gas. A conversion kit from NG to LP gas is packed with the hotplate. INSTALLER: Please leave these instructions with the User. DATA BADGE LOCATION...