Page 2 - Be safe; should be kept away; Gas and Electricity on
U108900-02 2 Be safe WarningAccessible parts will become hot in use. To avoid burns and scalds children should be kept away You need clean fresh air - so does your hotplate. Burner flames produce exhaust gases, heat and moisture. Make sure that the kitchen is well ventilated: keep natural ventilation...
Page 3 - U108900-02; Contents
3 U108900-02 Contents Hotplate Burners Page 4 Warmer Page 5 The Griddle (optional extra) Page 6 The Wok cradle (optional extra) Page 7 Cleaning your hotplate Page 8 Troubleshooting Page 10 General Safety Instructions Page 10 Installation Page 12 Conversion to LP gas Page 17 Circuit Diagram Page 20 T...
Page 4 - Hotplate Burners; not
U108900 - 02 4 Hotplate Burners The drawing by each knob indicates which burner that knob controls. 1 This example shows the knobs for the middle and front right burners. 2 There is a spark ignition system that works when the knob is pressed in. Each burner also has a special safety device that stop...
Page 5 - U18900-02; Warmer; Use only heat resistant dishes.
5 U18900-02 If a burner flame goes out, turn the control knob off and leave it for one minute before relighting it. You can remove the burner parts for cleaning; see the ‘Cleaning your hotplate’ section of the instructions. You should wipe the top surface of the hotplate around the hotplate burners as...
Page 8 - Cleaning your hotplate; Hotplate burners; The single ring burners
U108900 - 02 8 Cleaning your hotplate Essential information Before thorough cleaning isolate the electricity supply. Remember to switch on the electricity supply before using the hotplate. Never use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cle...
Page 9 - U18900-02; Outside of Hotplate
9 U18900-02 A electrode notch B ignition electrode Now fit the two burner caps, making sure that they are sitting down properly. Cleaning TableHotplate Part Finish Recommended Cleaning Method Hotplate Top Enamel or Stainless Steel Hot soapy water, soft cloth. Any stubborn stains remove gently with a ...
Page 10 - Troubleshooting; If you smell gas
U108900 - 02 10 Troubleshooting What cleaning materials are recommended for the hotplate? See the ‘Cleaning’ section for recommended cleaning materials. We do not recommend Mr. Muscle, as it contains chemicals that may damage the surfaces of your hotplate. If there is an installation problem and I d...
Page 11 - 1 U18900-02
11 U18900-02 Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleansers can produce noxious fumes if applied to a hot surface. Do not use unstable saucepans and position the handles away from the edge of the hotplate. Babies,...
Page 12 - Installation; Installer’s Name
U108900-02 12 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. Installation Dear Installer Before you start your installation, please complete the details BELOW. If your customer has a problem relating to your installation they will be able to contact you ea...
Page 13 - GAS PRESSURE TESTER
13 U108900-02 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. kit. After converting the appliance please attach the Gas Conversion sticker over the appropriate area of the data badge, this will identify the gas type the appliance is now set for. This applia...
Page 14 - Moving the Hotplate; gas connection union
U108900-02 14 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. We cannot accept responsibility for damage caused by normal use of the hotplate to any material that de-laminates or discolours at temperatures less than 65°C above room temperature.For safety re...
Page 15 - 5 U108900-02; Pressure testing; Pressures; Fixing the Hotplate; Electrical Connection; Note
15 U108900-02 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. For LP Gas it should be capable of 50mbar pressure, 70°C temperature rise and carry a red stripe, band or label. WARNINGS: Ensure that the gas supply pipe is never able to touch moveable parts of...
Page 16 - Electrical checks; Hotplate
U108900-02 16 INSTALLATION Check the appliance is electrically safe and gas sound when you have finished. If a replacement cable is fitted it must be 250v high temperature rubber/synthetic of 0.75mm 2 minimum conductor size. Connect the replacement cable to the terminal block on the hotplate as shown....
Page 17 - WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON; Conversion to LP gas
17 U108900-02 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Conversion to LP gas Check in the Technical Data section at the back of the book that the hotplate is convertible to ...
Page 18 - Stick on label
U108900-2 18 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished. Stick on label Stick the LP gas label over the natural gas part of the appliance data label. Pressure Testing Connect ...
Page 19 - 9 U108900-02
19 U108900-02 WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Page 20 - Circuit Diagram; or; Code Item
U108900 - 02 20 Circuit Diagram L N L N Warmer Switch Warmer Element Mains Terminal Block Spark Generator Ignition Swirches or bk b y b w w bk bk Warmer Neon bk D C1 A B C2 C3 Connection shown in circuit diagram is for single phase. Ratings are for 230V 50Hz Code Item A Ignition generator B Ignition...
Page 21 - Technical Data
21 U18900-02 Technical Data The hotplate is an independent Class 3 built in unit.This hotplate is category II 2H3+ It is supplied set for group H natural gas. A conversion kit from NG to LP gas is packed with the hotplate. INSTALLER: Please leave these instructions with the User. DATA BADGE LOCATION...
Page 23 - 3 U108900-02
