Polycom 1725-36071-001 - Manuals

Polycom 1725-36071-001 – Manual in PDF format online.

Manuals:

Manual

Manual Polycom 1725-36071-001

Summary

Page 2 - Trademark Information

Configuration Guide PN: 1725-36071-001_C.doc 2 Trademark Information Polycom® and the logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registered trademarks of Polycom, Inc. in the United States of America and various countries. All other trademarks used herein are the property...

Page 3 - Introduction; Certified Product Summary; Known Limitations

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 3 Introduction SpectraLink's Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink 8000 Wireless Telephones and WLAN infr...

Page 4 - Network Topology

Configuration Guide PN: 1725-36071-001_C.doc 4 Network Topology The following topology was tested during VIEW Certification. It is important to note that these do not necessarily represent all "certified" configurations. The access points were powered through a mid-span POE adaptor.

Page 5 - Installing Software & Configuration

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 5 Installing Software & Configuration 1. If software upgrades are required, contact Siemens Customer Support for the latest version of software and instructions. 2. The current version of software installed can be found...

Page 6 - Initial Setup

Configuration Guide PN: 1725-36071-001_C.doc 6 Initial Setup 1. The following instructions are for configuring a wireless controller and a number of access points with no prior configuration. 2. All of the initial setup is done via a web interface. Connect a ‘Cross-Over’ Ethernet cable directly from...

Page 7 - Controller Setup; Assigning an IP address to a wireless controller

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 7 Controller Setup The setup steps described below refer to the network topology diagram shown in this document. Make sure all the access points are disconnected from the system if configuring the system for the first time....

Page 9 - Assigning routing protocols to a wireless controller

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 9 Assigning routing protocols to a wireless controller 1. In the Wireless Controller screen, click Routing Protocols in the navigation pane. 2. Enter 0.0.0.0 for the Destination Address and 0.0.0.0 for the Subnet Mask . Add...

Page 10 - AP registration

Configuration Guide PN: 1725-36071-001_C.doc 10 AP registration 1. Click the Wireless APs button. 2. Click AP registration in the navigation pane. 3. Enter all information for your APs (see screen shot below). Make sure the setting for Security Mode is selected to Allow all Wireless APs to Connect. ...

Page 11 - AP maintenance

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 11 AP maintenance 1. In the Wireless APs screen, click AP Maintenance in the navigation pane. 2. Select the proper image file in the AP Images box and click the Set as default button. 3. Under Upgrade Behavior select the Up...

Page 12 - Setting up SSID, Security and QOS

Configuration Guide PN: 1725-36071-001_C.doc 12 Setting up SSID, Security and QOS 1. Click the VNS Configuration button. 2. Click the Topology tab. 3. Assign a subnet for clients for a specific SSID . 4. Under DHCP Settings : a. Enter the appropriate address for the Gateway b. For Mask enter 255.255...

Page 14 - Filtering

Configuration Guide PN: 1725-36071-001_C.doc 14 Filtering 1. In the VNS Configuration screen, click the Filtering tab. 2. Select Default from the Filter ID drop-down list. a. Select all three options - In, Out and Allow. b. Leave the IP:Port as *.*.*.* . 3. Select Non-Authenticated in the Filter ID ...

Page 15 - Multicast configuration

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 15 Multicast configuration 1. In the VNS Configuration screen, click the Multicast tab. 2. Select the Enable Multicast Support check box. 3. From the Defined groups drop-down list, select or enter Spectralink SVP (224.0.1.1...

Page 16 - Security

Configuration Guide PN: 1725-36071-001_C.doc 16 Security 1. In the VNS Configuration screen, click the Privacy tab. 2. For WPA2 AES-CCKM, click the WPA-PSK option, clear the WPA v.1 check box, then select the WPA v.2 check box. 3. For WPA TKIP, click the WPA-PSK option, clear the WPA v.2 check box, ...

Page 18 - Connecting access points to the controller

Configuration Guide PN: 1725-36071-001_C.doc 18 Connecting access points to the controller 1. Click the Reports button. 2. Make sure the controller is configured to accept new APs (this is selected by default). 3. Physically connect the access points to the system one at a time. Once an AP is connec...

Page 19 - Wireless APs address assignment

Siemens: HiPath Wireless System with 2610, 2620 APs PN: 1725-36071-001_C.doc 19 Wireless APs address assignment 1. After all the APs have been connected and discovered by the controller, click Wireless APs tab. 2. Click the Static Configuration tab. 3. Select an AP to configure. The AP’s name will d...

Page 20 - For each AP, follow the steps in the following sections:

Configuration Guide PN: 1725-36071-001_C.doc 20 For each AP, follow the steps in the following sections: AP properties 1. In the Wireless APs screen, click the AP Properties tab. Select an AP to configure. Here you can assign a meaningful name to each AP. 2. Enable Telnet Access . This is useful for...

Page 22 - Enable the radio

Configuration Guide PN: 1725-36071-001_C.doc 22 Enable the radio 1. Click the VNS Configuration button. 2. Click the Topology tab. 3. Enable each AP’s b/g radio for each SSID. 4. Set No. of Retries for Voice VO to adaptive (multi-rate) and No. of Retries for Turbo Voice TVO to 2 . 5. Click the Save ...