Polycom 1725-36060-001 - Manuals

Page 2 - Trademark Information

Configuration Guide PN: 1725-36060-001_D.doc 2 Trademark Information Polycom® and the logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registered trademarks of Polycom, Inc. in the United States of America and various countries. All other trademarks used herein are the property...

Page 3 - Introduction; Certified Product Summary

Trapeze Networks: Mobility System for MP 422 Access Points PN: 1725-36060-001_D.doc 3 Introduction Polycom’s Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink Wireless Telephones and wireless LA...

Page 4 - Service Information; Known Limitations; Access Point Capacity and Positioning

Configuration Guide PN: 1725-36060-001_D.doc 4 Service Information The AP must support SpectraLink Voice Priority (SVP). Contact your AP vendor if you need to upgrade the AP software. If you encounter difficulties or have questions regarding the configuration process of the Mobility Exchange, please...

Page 5 - Network Topology

Trapeze Networks: Mobility System for MP 422 Access Points PN: 1725-36060-001_D.doc 5 Network Topology The following topology was tested during VIEW Certification. It is important to note that these do not necessarily represent all “Certified” configurations. Both Layer-2 and Layer-3 roaming were te...

Page 6 - Access Point Setup and Configuration; Installing software; Text Style; Configuring the Mobility Exchange Switch; enable

Configuration Guide PN: 1725-36060-001_D.doc 6 Access Point Setup and Configuration Installing software Trapeze Mobility Exchange firmware cannot be downloaded from the SpectraLink website. Therefore, you must use the software that was shipped with your product, or contact Trapeze Networks for the l...

Page 7 - set service-profile Voice cipher-tkip disable; set service-profile Voice auth-psk enable

Trapeze Networks: Mobility System for MP 422 Access Points PN: 1725-36060-001_D.doc 7 Service profile commands (SSID & security policy setup) WPA2-PSK Assume you are creating service profile “vowlan-wpa2” to define the ESSID “phones,” as well as a WPA2-PSK security policy. The following commands...

Page 8 - Radio profile commands; or the

Configuration Guide PN: 1725-36060-001_D.doc 8 # defines a passphrase set service-profile Voice auth-psk enable # enables pre-shared key authentication set service-profile Voice auth-dot1x disable # disables 802.1x authentication set service-profile Voice attr vlan-name default # maps the handsets t...

Page 9 - Radio configuration; SVP configuration

Trapeze Networks: Mobility System for MP 422 Access Points PN: 1725-36060-001_D.doc 9 Radio configuration During VIEW Certification, the MP access points were tested directly connected to a port on the MX (e.g. port 1). The following commands will configure a specific access point’s radio to support...

Page 10 - The following commands are performed on the seed MX switch:; set igmp disable vlan v1

Configuration Guide PN: 1725-36060-001_D.doc 10 Subnet roaming configuration between multiple MX switches To set up subnet roaming between two switches, a mobility domain must be configured on both switches. Choose one of the switches to be the “seed” switch. The IP addresses used in mobility domain...

Page 11 - Checking the configuration; Trapeze

Trapeze Networks: Mobility System for MP 422 Access Points PN: 1725-36060-001_D.doc 11 Checking the configuration Once the switch is configured, issue the following command at the command prompt to check the SVP settings: sh ap qos-stats The following information should be displayed (repeat the comm...

Page 12 - show configuration all

Configuration Guide PN: 1725-36060-001_D.doc 12 Configuration File (For Reference Only) The following configuration file was used during VIEW Certification testing. The configuration below includes all configuration attributes, including defaults. Use the command show configuration all for this deta...