ParaBody Hip Sled System - Manuals

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 835 Hip Sled System. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. 3 NOTE: BOLT LENG...

Page 5 - PARTS LIST

5 PARTS LIST PART # LEA6504909 LEA6506809 LEA7337609 LEA6507709 LEA6507809 LEA6667809 LEA6505910 LEA7337309 LEA7337409 LEA6504410 LEA7337710 LEA6506610 LEA6507010 LEA6521210 LEA6534310 LEA6667910 LEA6509221 LEA6666921 LEA6667321 LEA6500501 LEA6500601 LEA3103101 LEA3103104 LEA3116001 KEY 1 2 3 4 5 6 ...

Page 6 - FIGURE 1

FIGURE 1 STEP 1: • LOOSELY assemble the RIGHT (4) and LEFT HANDLES (5) to the BASE (1) on their respective sides using four 3/8 X 3” BOLTS (37), eight 3/8” WASHERS (29), and four 3/8” LOCK NUTS (31) (DO NOT SECURELY TIGHTEN AT THIS TIME) 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the ...

Page 7 - FIGURE 2; FIGURE 3

FIGURE 2 STEP 2: 7 • Insert four 1/2” FLANGE BEARINGS (46) into the BUSHINGS on the BASE (1), and four 1/2” FLANGE BEARINGS (46) into the BUSHINGS on the PLATFORM (11) as shown in FIGURE 2. • Assemble the PLATFORM (11) between the BUSHINGS on the BASE (1) as shown in FIGURE 2 using two 1/2 X 5” BOLT...

Page 8 - FIGURE 4

STEP 4: 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Assemble the PLATFORM SLEEVE (2) to the BASE (1) as shown in FIGURE 4 using one 1/2 X 4” BOLT (42), and one 1/2” LOCK NUT (33). (TIGHTEN THE CONNECTION ENOUGH TO REMOVE THE PLAY, YET ALLOWING THE PLAT- FORM SLEEVE TO ROTATE FREELY) • Pull back the 1/...

Page 9 - FIGURE 5

FIGURE 5 STEP 5: 9 • LOOSELY assemble the LEFT (8) and RIGHT RAILS (9), along with the SEAT PAD (18) to the BASE (1) as shown in FIGURE 5 using two 3/8 X 4-1/2” BOLTS (38), two 3/8” LOCK WASHERS (30), and two 3/8” WASHERS (29). Temporarily assemble theRAILS to the REAR UPRIGHT (6) using two 1/2 X 4-...

Page 10 - FIGURE 6

FIGURE 6 STEP 6: 1 0 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Insert four 2” SQ. END CAPS (26) into the each end of the CARRIAGE (16) as shown in FIGURE 6. • SECURELY assemble four 3” DIA. WHEELS (20) to the sides of the CARRIAGE (16) as shown in FIGURE 6 using four 1/2 X 4-1/2” BOLTS (43), eight 1/2...

Page 11 - FIGURE 7

FIGURE 7 STEP 7: 11 • SECURELY assemble two 2” DIA. WHEELS (21) to the BRACKETS on the left side of the CARRIAGE (16) as shown in FIGURE 7 using two 3/8 X 2” BOLTS (36), four 3/8” WASHERS (29), and two 3/8” LOCK NUTS (31). • Assemble the two ADJ. WHEEL BRACKETS (14) to the right side of the CARRIAGE...

Page 12 - FIGURE 8

FIGURE 8 STEP 8: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1 2 • Remove the two temporary 1/2 X 4-1/2” BOLTS (43) from STEP 5 . • Swing the LEFT (8) and RIGHT (9) RAILS out enough to insert the CARRIAGE ASSEMBLY (16) in between them. Allow the CARRIAGE (16) to rest on the SAFETY STOPS underneath the RAI...

Page 13 - FIGURE 9; REVERSE VIEW

FIGURE 9 1 3 • SECURELY reassemble the LEFT (8) and RIGHT (9) RAILS to the REAR UPRIGHT (6) as shown in FIGURE 9 using the two 1/2 X 4-1/2” BOLTS (43), four 1/2” WASHERS (32), and two 1/2” LOCK NUTS (33). (!!! IMPORTANT !!! BEFORE TIGHTENING MOVE THE RAILS IN AS FAR AS POSSIBLE) STEP 9: • SECURELY t...

Page 21 - THIS CONCLUDES THE ASSEMBLY OF THE 835 HIP SLED SYSTEM.

FIGURE 17 STEP 17: 2 1 • To perform LEG PRESSES, center the BACK PAD (19) down on top of the PLATFORM (11) and lock the PAD STOP (15) on the back of the BACK PAD (19) behind the PLATFORM HANDLE then rotate the FOOT PLATE (10) on the CARRIAGE (16) upuntil the SPRING PIN engages the hole • To perform ...

Page 22 - SERIAL NUMBER LOCATIONS

MAINTENANCE MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 2 2 * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be pur...

Page 23 - LIMITED WARRANTY

2 3 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...