ParaBody 844 - Manual - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 844 Lat Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. 3 NOTE: BOLT LENGTH IS...

Page 4 - PARTS LIST; FIGURE 1

4 PARTS LIST PART # LEA6608709 LEA6608509 LEA6274410 LEA6275310 LEA6609010 LEA6610410 LEA6546310 LEA6609309 LEA3116101 LEA3116201 LEA6610501 LEA6576201 LEA6176201 LEA6542402 LEA3103102 LEA3235208 LEA3235211 LEA3235212 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 QTY 1 1 1 1 1 1 1 1 1 5 1 1 2 2 4...

Page 5 - FIGURE 2

5 FIGURE 2 STEP 2: • SECURELY assemble the UPRIGHT (1) to the LOW PULLEY HOUSING (8) using two 1/2 X 3” BOLTS (24), two 1/2” WASH- ERS (25), and one 1/2” LOCK NUTS (26). See FIGURE 2. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 1 5 2 0 2 1 POWER RACK 3/8 X 3-1/4” 19 2 0 2 6 1/2 X 3” 24 2 5 8 • Assemble th...

Page 6 - FIGURE 4; FIGURE 3

6 STEP 4: FIGURE 4 • CAREFULLY slide the CARRIAGE (7) over the UPRIGHT (1) as shown in FIGURE 4. 7 1 FIGURE 3 STEP 3: • Apply eight 1” SQ. GLIDES (31) to the inside of the CARRIAGE (7) as shown in FIGURE 3. • Attach one 1-1/4” SQ. RUBBER BUMPER (30) to the bottom of the CARRIAGE (7) as shown in FIGU...

Page 7 - CABLE DIAGRAM

CABLE DIAGRAM 7 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2

Page 8 - FIGURE 5

8 • SECURELY assemble three 3-1/2” PULLEYS (10) to the TOP BOOM (2) using three 3/8 X 2-3/4” BOLTS (17), six 3/8” FLANGE SPACERS (22), and three 3/8” LOCK NUTS (21). See FIGURE 5. (NOTE: BEFORE TIGHTENING, MAKE SURE CABLE (11) IS IN THE GROOVES OF THE PULLEYS.) STEP 5: • Insert one 2 X 3” END CAP (2...

Page 9 - FIGURE 6

9 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 6: FIGURE 6 • SECURELY assemble the TOP BOOM (2) to the UPRIGHT (1) using one 1/2 X 2-3/4” BOLT (23), one 1/2 X 3” BOLT (24), two 1/2” WASHERS (25), and one 1/2” LOCK NUT (26). See FIGURE 6. • SECURELY assemble the TOP BOOM (2) to the top of the POWER RAC...

Page 10 - FIGURE 7

1 0 STEP 7: FIGURE 7 • Loop the LAT CABLE (11) around one 3-1/2” PULLEY (10) as shown in FIGURE 7. • LOOSELY assemble the 3-1/2” PULLEY (11) to the1-3/4 X 5-1/4” PLATES (14) using one 3/8 X 2” BOLT (16) and one 3/8” LOCK NUT (21). See FIGURE 7.

Page 11 - FIGURE 8; FIGURE 9

STEP 8: FIGURE 8 • Attach the LAT CABLE (11) to the CARRIAGE (7) using one 1/4” QUICK LINK (34) as shown in FIGURE 8. (IMPORTANT! Securely tighten QUICK LINK.) !IMPORTANT! SECURELY TIGHTEN 3 4 7 FIGURE 9 STEP 9: • Loop the ball end of the LOW ROW CABLE (12) around one 4-1/2” PULLEY (9) and SECURELY ...

Page 14 - THIS CONCLUDES THE ASSEMBLY OF THE 844 LAT OPTION

FIGURE 15 STEP 15: • When performing the LAT PULL exercise, insert the KNEE SUPPORT (6) into the hole of the SAFETY RAIL as shown in FIGURE 15 and simply lower the SAFETY RAIL down until roller pads contact knees. 6 1 4 SAFETY RAIL THIS CONCLUDES THE ASSEMBLY OF THE 844 LAT OPTION

Page 16 - LIMITED WARRANTY

1 6 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...

ParaBody 844 - Manual

Table of Contents:

Summary

Other ParaBody Models