ParaBody GS2 - Manual - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody GS2 Gym System. Please read these instructions thoroughly and keep them for future reference. * Rubber mallet or hammer* 3/4” wrench* 9/16” wrench* Ratchet with 3/4” and 9/16” sockets* 5/32” Allen wrench...

Page 5 - PARTS LIST

5 PARTS LIST 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PART # ACU04-1163 ACU04-1158 ACU02-1060 ACU04-1160 ACU04-1384 ACU04-1383 ACU04-1161 ACU04-1164 ACU04-1159 ACU04-1162 ACU04-1157 ACU02-1071 ACU07-0135 ACU01-1782 ACU6194601 ACU01-1783 ACU04-1099 ACU01-2009 ACU10-0204ASY ACU13-0091-2 ACU13-0019-1 ACU7...

Page 6 - FIGURE 1

FIGURE 1 6 STEP 1: 1 3 4 3 0 2 62 3/8 X 3 2 9 34 3 • LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30) and four 3/8” LOCK NUTS (34). See FIGURE 1. 3 4 6 3 3/8 X 4 36 • LOOSELY assemble the FOOTPLATE (62) to the lower holes in the FRAME (1) using on...

Page 8 - FIGURE 4; FIGURE 5

• Insert two GUIDE RODS (16) into the BASE (2) as shown on FIGURE 4. (NOTE: If the GS2 SHROUD OPTION was purchased, place the GUIDE RODS(16) through the BOTTOM SHROUD BRACKET (FOUND IN THE SHROUD KIT BOX ) into the BASE (2), as shown in FIGURE 4. • Using EXTREME CARE slide all fifteen WEIGHT PLATES ...

Page 10 - FIGURE 8

FIGURE 8 8 4 9 2 9 3 6 9 3 4 STEP 8: • Place PRESS ARM (8) into PRIMARY PIVOT (9) and securely tighten using two 3/8 X 3” BOLTS (29), four 3/8” FLAT WASHERS (36) two 3/8” LOCK NUTS (34) • Insert and tighten two 3/8” TAPER/LOCK SPRING PINS (49) into PRESS HANDLES (6), (7). TIGHTEN20lbs/ft 1 0 • Lock ...

Page 11 - FIGURE 9

FIGURE 9 11 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9 • SECURELY TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING TO NEXT STEP 3 3 3 7 6 0 4 8 9 1/2 X 8-3/4” SECURELYTIGHTEN • SECURELY TIGHTEN top of both SHAFT COLLARS (48) flush to bottom of both BOOM PLATES (4),(5) 1 4 0 • Assemble the PRIMARY PI...

Page 14 - ILLUSTRATION A

ILLUSTRATION A NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER TO THE CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEGPRESS KIT 1 4 • ILLUSTRATION “A” used as cable routing reference for steps 13-16

Page 22 - SERIAL NUMBER LOCATION

MAINTENANCE MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 2 2 * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be pur...

Page 23 - LIMITED WARRANTY

2 3 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...

ParaBody GS2 - Manual

Table of Contents:

Summary

Other ParaBody Models