ParaBody 445104 - Manuals - manualsarea.com

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH; WELCOME TO THE WORLD OF

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the Parabody 445104 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber m...

Page 3 - PARTS LIST

STEP 2 FIGURE 2 FIGURE 1 STEP 1 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1. 3/8” X 1” BUTTON HEAD CAP SCREW PART # 6523401 6266001 6375902 6714601 6747501 3116101 6214401 3108002 3117401 3102501 KEY 1 2 3 4 5 6 7 8 9 10 QTY 2 1...

Page 4 - FIGURE 3

STEP 3 FIGURE 3 4 • Unscrew the threaded ends of the HEAD PLATE CABLE from the WEIGHT STACK SHAFT & the D-RING and remove HEAD PLATE CABLE. The HEAD PLATE CABLE will be used later. See FIGURE 3. (NOTE: Remove pulleys for ease of removal.) HEAD PLATE CABLE ( 6 7 2 5 0 ) D-RING 0 1 2 3 4 5 6 1/2 1...

Page 6 - FIGURE 6; FIGURE 7; LOOSELY

6 STEP 6 FIGURE 6 • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOLT (11), one previously removed 3/8” WASHER, and one previously removed 3/8” LOCK NUT. See FIGURE 6. • (NOTE: STEP 6 is only if the 435101 LEG PRESS OPTION is installed otherwise proceed...

Page 7 - SECURELY

FIGURE 8 STEP 8 • Discard the two 3/8 X 1/2” SPACERS. • Remove two 2” PULLEYS (5) to the rear bracket on the TOP BOOM using one 3/8” THREADED SHAFT (9), two 3/8” WASHERS, two 3/8” HEX NUTS (8), and two 3/8” LOCK NUTS (7) as shown in FIGURE 8. FIGURE 9 STEP 9 • Position the elastic cords over the 2” ...

Page 8 - Carefully; remove and discard the PRESS CABLE as shown in FIGURE 10.

STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10. PRESS CABLE (67249) FIGURE 10 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2

Page 10 - LOOSEN

FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14. 10 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 • Insert two WEIGHT PLATE BUSHINGS (17) into the top side of each of the fifteen WEIGHT PLATES (16) as...

Page 11 - spray available at most hardware stores.); EXTREME CARE

FIGURE 15 STEP 15 • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) • Slide two 1-1/4 SQ. X 4-7/8” TUBES (3), two 3/4” WASHERS (15), and two WEIGHT STACK CUSHIONS (8) - IN THAT ORDER - dow...

Page 12 - CABLE runs over the top of the bolts in the TOP BOOM.); CAREFULLY

STEP 16 FIGURE 16 12 • With the GUIDE RODS (1) securely held in the TOP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sure the LAT CABLE runs over the top of the bolts in the TOP BOOM.) 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! ( NOTE: Make sure LAT CABLE runs over top ofbolts in TOP BOOM...