Page 2 - TABLE OF CONTENTS
TABLE OF CONTENTS WARNINGS AND SAFETY INFORMATION 1 GETTING STARTED 3 YOUR BABY MONITOR 6 BASIC OPERATION 10 TROUBLESHOOTING 15 PRODUCT SPECIFICATIONS 16 GUARANTEE 17
Page 3 - Power requirements; CAUTION; WARNINGS AND SAFETY INFORMATION; IMPORTANT
1 Do not place the cord in a high "wear and tear" location. Never use a frayed or compromised cord. Never use or place your Parent or Baby units in or near moisture or water (e.g. near bath or pool). Immersing in water can cause electric shock and even death. Power requirements This product ...
Page 4 - Battery requirements
2 WARNINGS AND SAFETY INFORMATION Battery requirements E a c h p a r e n t u n i t r e q u i r e s t w o r e c h a r g e a b l e N i - M H batteries, size AA 1.2V 1300mAh. • Do not dispose of the batteries in a fi re, as they can explode. • Do not open, unscrew or temper with any of your baby monito...
Page 5 - Installation and Charger; For the Parent Unit; WARNING; GETTING STARTED; Pack Contents
3 Installation and Charger For the Parent Unit 1 Remove the battery cover on the back of the Parent U n i t b y p r e s s i n g a n d sliding it down. Insert the rechargeable batteries as marked on the unit and close the cover again. 2 Place the Parent Unit into the Charger Pod. 3 Plug the mains ada...
Page 6 - For the Baby Unit
4 4 Press [ ] to turn the Parent Unit on. • Before fi rst use, or if it has been out of use for a long time, the Parent Unit will need to be charged for 14 hours. During this time, the Parent Unit will operate from the Charger pod when switched on. Note that the Parent Unit cannot be used without ba...
Page 7 - Wall mounting the Baby Unit
5 GETTING STARTED Wall mounting the Baby Unit Use the following wall mount diagram to locate and install the mounting pins/screws if you prefer to wall mount your base unit. The dimensions are shown in millimeters (mm). Ø 4.00 Ø 7.55 58.00 1. Insert screws into the wall through the wall mount. The r...
Page 8 - YOUR BABY MONITOR
6 YOUR BABY MONITOR Baby unit (Sender) Page Press to page the Parent unit – useful for fi nding when it is misplaced. Power on/off Press to switch on or off. Link light Green when linked to Parent unit. Flashes if not linked - fi rst 30 seconds. Flashes when Talk is pressed on Parent unit. Red fl as...
Page 9 - Back of Baby unit; Underside
7 YOUR BABY MONITOR Back of Baby unit Underside Power socket For connection to mains power. Battery lock Child tamper proof lock for the battery compartment.
Page 10 - Parent unit
8 YOUR BABY MONITOR Parent unit From the Parent unit you can listen to your baby and operate the Baby unit by remote control. Talk (on side of unit) Press to talk to your baby. LED Link indicator Green On – Linked to Baby unit Green fl ashing – Not linked to Baby unit – fi rst 30 seconds Red Flashin...
Page 11 - Parent unit charger; Front
9 YOUR BABY MONITOR Parent unit charger Charging light Indicates Parent unit is charging. Power socket For connection to mains power. Front Back
Page 12 - BASIC OPERATION; Baby Unit; Monitoring
10 BASIC OPERATION Once you have set up your Baby Monitor, you will be able to hear the sounds in your baby’s room through the Parent Unit. And also see the green and red sensor lights around the top of the Parent Unit rise and fall with the sound levels. Note: If the connection between the Parent a...
Page 13 - Sensitivity; Mute
11 BASIC OPERATION • If the volume of the Parent Unit is turned off, an alert will sound when the audio picked up reaches the second red led. Note: Do not position the baby unit and the parent unit close to each other or in the same room as feedback may be generated. You can press [Mute] key to temp...
Page 14 - Talk Back; Adjust Talk Back volume
12 BASIC OPERATION Talk Back You can use the talk back feature to talk to your baby. • Press and hold [Talk] key on the Parent unit to speak to baby. The green link lights on both Units fl ash. • Talk into parent unit's microphone.• Release [Talk] key to hear your baby again. Adjust Talk Back volume...
Page 15 - Lullaby; Playing the Lullaby; Out of Range; Low Battery
13 BASIC OPERATION Lullaby The Baby unit plays lullabies to gently soothe your baby back to sleep. Each lullaby is played repeatedly for 15 minutes. Select one of the three melodies or select Play All for a medley of all 3 lullabies for 15 minutes. The Lullaby LEDs indicate which lullaby is playing ...
Page 16 - Charging the Battery
14 BASIC OPERATION Note: Low battery alert can be suppresed by pressing any button. Charging the Battery Place the parent unit on its charger pod to charge the battery. When charging, the red light on the charger will light steadily. The Low Battery light will be turned off. Note: The Parent Unit mu...
Page 17 - TROUBLESHOOTING
15 TROUBLESHOOTING Problem Possible cause(s) The red power lights do not turn on when you plug in the power. 1. Check if the units are properly connected to the power supply.2. Check if the power is turned on. If not, Press [ ] to turn on the power. The green Link light on the Parent Unit is fl ashi...
Page 18 - PRODUCT SPECIFICATIONS
16 PRODUCT SPECIFICATIONS Feature Speci fi cations Operating Frequency 1.8 GHz Range Up to 300 m under optimum conditions. The range is reduced in buildings (up to 50 m) as a result of walls, doors etc. Power supply (parent unit / baby unit) Input: 100 - 240 V AC 50 - 60 Hz Output: 7.5 V DC , 500 mA...
Page 19 - GUARANTEE; Customer Support
17 GUARANTEE Warranty (Australia) (a) Warranty Oricom International Pty Ltd (Oricom) warrants that the product is free from defects in materials and workmanship for a period of 12 months effective from the date of purchase. This warranty in no way affects your statutory warranty under the Trade Prac...