Omega DRN-PS-1000 - Manuals

Page 3 - ONTENTS

1. General Information and Features 2 2. Safety Considerations 3 3. Installation and Removal 4 3.1 Installation Clearance 5 3.2 Mounting on DIN Rail 6 3.3 Removal of Unit 7 4. Input and Output Connections 8 4.1 Block Diagram 8 4.2 Wiring for 115 Vac - Single Phase 9 4.3 Wiring for 230 Vac - Two Phas...

Page 4 - Features; ENERAL

The compact DRN power supplies are designed tosupply well-regulated 24 volt DC power to sensors,signal conditioners, data acquisition systems andhigh level logic equipment. Significant DRN features include:¥ Tested isolation, primary to output ¥ Recessed live parts and connector screws ¥ Either 32mm...

Page 7 - NSTALLATION AND; Power Supply

3.1 Installation Clearance Ensure that there is enough room for mounting the power supply unit. There should be a minimum of 1" [25mm] spacingto allow sufficient air circulation for proper cooling. Figure 3.1 Ñ Mounting I NSTALLATION AND R EMOVAL 3 5 Signal ConditionerModules Power Supply 24V-Bu...

Page 8 - Mounted on 32mm DIN Rail; Mounting Guide

3.2 Mounting on DIN Rail To install unit onto DIN Rail1. Tilt unit position mounting guide onto DIN Rail, as shown.2. Push unit towards DIN Rail and it will snap into place. Figure 3.2 Ñ Mounting on 35mm DIN Rail Figure 3.3 Ñ Mounted on 32mm DIN Rail I NSTALLATION AND R EMOVAL 3 6 35mm Rail Mounting...

Page 9 - will detach from mounting guide.; Removal of Unit; Hold Guide

3 7 3.3 Removal of Unit The mounting guide can remain on DIN Rail and Power Supply can be removed.1. While holding mounting guide, push unit upwards and unit will detach from mounting guide. Figure 3.4 Ñ Removal of Unit Figure 3.5 Ñ Unit Removed I NSTALLATION AND R EMOVAL Mounting Guide CASE TAB MUS...

Page 10 - Block Diagram of Power Supply; Figure 4.1 Ñ Block Diagram; Do not turn on the ac power to the power supply; NPUT AND

4 8 4.1 Block Diagram of Power Supply Figure 4.1 Ñ Block Diagram 4.2 Wiring Warning: Do not turn on the ac power to the power supply unit until you have completed all output connections. Failureto do so may result in injury! This device must only be installed electrically by a specially trained elec...

Page 11 - 15Vac - Single phase power wiring; Figure 4.2Ñ Wiring for 115Vac - Single Phase; Input Power; USE A SWITCH TO APPLY; FUSE; Output Voltage

4 9 I NPUT AND O UTPUT C ONNECTIONS 4.2 Wiring (Continued) 115Vac - Single phase power wiring Figure 4.2Ñ Wiring for 115Vac - Single Phase Input Power * • USE A SWITCH TO APPLY • +24V POWER TO THE LOAD,• IF THE CAPACITANCE OF• THE LOAD WILL DRAW MORE• THAN 7 AMPS AT TURN ON. USE AWG 12-26 WIRE (for ...

Page 12 - 30Vac - Two phase power wiring; Figure 4.3Ñ Wiring for 230Vac - Two Phase

4.3 Wiring (Continued) 230Vac - Two phase power wiring Figure 4.3Ñ Wiring for 230Vac - Two Phase I NPUT AND O UTPUT C ONNECTIONS 4 10 Output Voltage (for shielded wireconnections, if necessary) Earth FUSE 1 L1 Switch L 2 Earth FUSE 2 Switch * * • USE A SWITCH TO APPLY • +24V POWER TO THE LOAD,• IF T...

Page 13 - PECIFICATIONS; INPUT POWER; Front Panel LED

S PECIFICATIONS 5 11 INPUT POWER Input Voltage: 115 - 240Vac ±10% Frequency: 50/60 Hz Current: 0.400A @ 103Vac 0.190A @ 265Vac Overvoltage Protection: 275 Volt VaristorOvercurrent Protection: Fuse TR-5 800mA Time-lag / IEC 127-3Input Wattage: 26 Watts OUTPUT POWER Output Voltage: 24Vdc ±2% @ 850mA (...

Page 14 - GENERAL; Operating Temperature:; WIRE CONNECTIONS

S PECIFICATIONS 5 12 GENERAL Operating Temperature: 23¡ to 122¡F(-5¡ to 50¡C) Storage Temperature: -40¡ to 176¡F(-40¡ to 80¡C) Mounting: 32 and 35mm DIN Rail Size: Height: 3.00" (76mm) Width: 0.9" (23mm) Depth: 3.67" (93mm) Weight: 0.3 lbs. (0.14 kg) Equipment Type: CLASS I Overvoltage: ...

Page 15 - IMENSIONS

D IMENSIONS 6 13 3.67" (93mm) 3.00" (76mm) 0.9" (23mm)

Page 16 - Figure 6.2 Ñ Temperature Derating Graph; MAXIMUM POWER OUTPUT; AC INPUT CURRENT @ 100VAC INPUT

I NPUT AC VOLTAGE / POWER OUTPUT 7 14 Example: If ambient is 50¼C, maximum wattage is 21W max. for120-265Vac. If unit is operated at 21W at an input voltage of 100V,the maximum ambient temperature allowed is 40¼C. Figure 6.2 Ñ Temperature Derating Graph MAXIMUM POWER OUTPUT INPUT AC VOLTAGE AMBIENT ...